Looking to buy/ sell a stick? ***READ HERE***

K.O.Kiki wrote: »

Do you want to only replace the spring?
The stick in TEs (and HRAPs) is a Sanwa JLF; check this thread for more info.


You could print your new art and have it laminated - should only cost around a fiver.
Just make sure it's printed on A3 and double-check dimensions before cutting/laminating.

thanks for the info man

ahh i just read if you throw another spring in with the stock one you get a bit of a stiffer stick?

a 5 aint bad at all for a alternative where would i go for this service?

UberPrinny_Baal wrote: »

Bought this converter, it just arrived in the post today

http://www.szprice.com/products/3-in-1-Comverter-PSX-and-PS2-to-PC-USB-X-box-Gamecube_2869.html

Funny thing, looks like a little Xbox. Anyone else have it already?

I have something similar. It converts to the same things, but may not be the same brand.

Mine only worked as Player 2 on PS3 for some reason though and the buttons were all swapped for the one next to them.

Worked fine on the old xbox, GC and PC though.

Also works fine on Wii for TvC and GG.

chopperbyrne wrote: »

Mine only worked as Player 2 on PS3 for some reason though and the buttons were all swapped for the one next to them.

Did you check to make sure there were any buttons on the device you may have pressed accidentally? I know you've had issues with that sort of thing in the past.

1man3letters wrote: »

anyone use arcadeforge.de before?
trying to find somewhere in europe to do plexi for my te? (if anyone knows anyone better be helpfull)
thanks

ArcadeForge is trustworthy; haven't used him myself though.

Also, send him an email first about plexi availability, just-in-case.

1man3letters wrote: »

when you say heat and friction, could u go into a bit more detail?
comfort is key to me as i only have one stick

Well I did the laminate before, and the way I play the heel of my hand rests below the buttons, and I slide the heel constalty left to right. After just a couple of weeks the lamiate started to bubble and peel away. Mostly because of the way I play though.

I went with the plexi from arcade forge before and I still have it in perfect condition, I would definitley recommend them. But as Kiki say's check with him first as he gets very busy.

Sagat06 wrote: »

Well I did the laminate before, and the way I play the heel of my hand rests below the buttons, and I slide the heel constalty left to right. After just a couple of weeks the lamiate started to bubble and peel away. Mostly because of the way I play though.

I went with the plexi from arcade forge before and I still have it in perfect condition, I would definitley recommend them. But as Kiki say's check with him first as he gets very busy.

thanks man. ill go with the plexi so.yea i seen your blanka one the other thread,shes nice, saldy arcade forge dont do art at the monment

Was there a particular type of card you had the artwork printed on from Reids?

I'd imagine trying to cut the holes out for buttons might be a little awkward with the more flimsy sort of paper...

Monkeyto wrote: »

Was there a particular type of card you had the artwork printed on from Reids?

I'd imagine trying to cut the holes out for buttons might be a little awkward with the more flimsy sort of paper...

Unless you pick up one of these
https://www.petenplanes.com.au/tools-gadgets/tools-gadgets/hobbico-circle-cutter-hcar0230/prod_77.html
I got one delivered for about 4 euros on ebay a while back.

Reads is on Nassau Street in Dublin. Runs perpendicular to grafton street if you don't know the city.

unky chop chop wrote: »

I have a spare 6 button plexi going a begging if ya want it.

thanks for the offer man but im going to stick to a 8 button layout for this stick

I certainly can.

unky chop chop wrote: »

I have a spare 6 button plexi going a begging if ya want it.

I'll take it off your hands if it's going!

*Sent a pm*

OMGZZZZZZZZZ

http://www.d3vlicious.com/home/2011/7/16/sanwa-to-produce-clear-pushbuttons.html

FINALLY


also if any1s interested in purchasing this

http://www.adverts.ie/xbox/original-xbox-with-2-games-accessories/729529

mackg wrote: »

I'm going ordering the qanba q4-raf stick and I get a free gift a choice between:

a clear plexi cover
sanwa gt-y octagonal gate
sanwa lb-30n bat top handle

What would ye recommend?

I'd go for the plexi.
I have no interest in an oct-gate and I've never hugely liked bat tops, so it's an easy choice for me! :pac:

Gotta ask does anyone know of somewhere that does plexis for my Hrap V3, i looked quite a bit and only thing i could find was some dude on SRK, but postage from america to here would be killer for something that size