Today I did something to my car (volume 2)

Atlantic Dawn · 08-03-2019 08:46PM

Lovely job, did you have to take it off to spray it or just cover around it before you sprayed?

Toyotafanboi · 08-03-2019 09:34PM

Did you ask them why it wasn't painted?

We have found that no matter how small an item we have to paint, painting incurs a certain minimum cost which is quite high. Painting any article smaller than a body panel costs €60+ VAT and even at that you dont really make anything on it. That's towing eye covers, door handles, headlamp washer jet covers, mirror caps, fuel filler doors etc.

I used to keep the defibrillator on standby when quoting people. 95% would decline the whole thing.

Noccy_Mondy · 09-03-2019 08:49AM

Atlantic Dawn wrote:

Lovely job, did you have to take it off to spray it or just cover around it before you sprayed?

Oh ya I took it off, there's nothing to it really. Would be a botched job otherwise

Toyotafanboi wrote:

Did you ask them why it wasn't painted?

No, tbh I had nothing to do with the whole thing, but they didn't even say they were going to put on a bog spec handle onto it. Fair enough if they did then we could decide for ourselves whether to go ahead or not. If it was my own golf and it was returned that way I'd have kicked up a fuss. Only for the fact that I had the paint and lacquer, primer there I would have made sure it was brought back. Like they're a common car, if they hadn't a colour coded one, there's plenty of breakers that do (even though that may not be their policy)

TrailerBob · 09-03-2019 09:10PM

Toyotafanboi wrote: »

Did you ask them why it wasn't painted?

We have found that no matter how small an item we have to paint, painting incurs a certain minimum cost which is quite high. Painting any article smaller than a body panel costs €60+ VAT and even at that you dont really make anything on it. That's towing eye covers, door handles, headlamp washer jet covers, mirror caps, fuel filler doors etc.

I used to keep the defibrillator on standby when quoting people. 95% would decline the whole thing.

I had a door handle replaced a few years back after a break in. Main Toyota dealer did the job. I came out and found a chrome effect handle on the driver's door.. the rest are matte black... I simply and calmly went back in and said that's not good enough. Next day it was replaced with the the right one. Couldn't believe they tried it on. Doesn't matter how old the car.

fancy pigeon · 11-03-2019 10:55AM

The niggly little bits... Tidied up some of the shoddy wiring behind the radio, fitted some missing screws and the vent beside me was broken, no pics of those unfortunately.

However...

Tab broken on a connector

Broken buttons? Make a good vent out out of 2!

More crappy little bits in due time...

Toyotafanboi · 14-03-2019 10:04PM

Made a little mod on my Golf, even though I promised myself I wouldn't waste money on this sort of thing, but this was mega cheap.

I acquired a switch with the auto function for free so that helped, then I got one of these little light sensors, they are on Ebay, Amazon etc for like €20.

Pop the old switch out, the light sensor connects between the back of the switch and the loom plug for the switch, plug and play. Ran the cable behind the dash and up beside the A-Pillar. The sensor isn't stuck down in the photos (nor is the switch fully seated in the dash) but I stuck it in right to the pillar with the excess cable hidden. These were just a few quick pics while I done it during a stolen ten minutes I had.

Not only does this enable auto lights but the switch also allows you to activate guide me home lights and welcome lights that activate with the central locking without having to use ODIS etc to activate the function, just a sequence of switch selections to activate it.

Also didn't need a single tool to do this, which is always nice.

https://m.ebay.ie/itm/202078437639?ul_ref=http%3A%2F%2Frover.ebay.com%2Frover%2F1%2F5282-53468-19255-0%2F1%3Ftype%3D2%26pub%3D5575403537%26toolid%3D10001%26campid%3D5338343602%26item%3D202078437639%26customid%3Dvms%253Aeb%253Ap%253A202078437639%253BEAIaIQobChMI46SWurOC4QIVS7ftCh1QJAFmEAQYAiABEgKlhvD_BwE%26gclid%3DEAIaIQobChMI46SWurOC4QIVS7ftCh1QJAFmEAQYAiABEgKlhvD_BwE%26srcrot%3D5282-53468-19255-0%26rvr_id%3D1895573927647%26rvr_ts%3D7dc06a951690aa18c4e41390ffe991e2&_mwBanner=1&_rdt=1&ul_noapp=true

Also got these genuine rubber mats a while back. A real bogger spec item but necessary at the moment as despite my best efforts I'm dragging a lot of muck into the car on the weekends. I have fitted carpet mats to switch back to later on anyway.

CJhaughey · 15-03-2019 05:43PM

Wifes Impreza boot wouldn't lock shut.
Took the interior panels out and the locking mechanism was staying open and wouldn't latch shut.
Removed the mechanism and disassembled it there was a tiny electric motor with a worm drive and a larger gear with a spring on the back of it that turned a lever with a quadrant that opened the latch.
Regreased and reset the lever and it didn't work, I pulled it apart 3 times before I got it set correctly.
Works well now, why they did away with a simple cable release I will never know.

dingdong1234567 · 15-03-2019 05:46PM

Two days on the A4, two front wheel bearings and a drive shaft. Whore of a job. Runs like butter now.

fancy pigeon · 21-03-2019 10:33AM

Noticing my brake pedal was a bit off and with a small screech starting to appear, I decided to have a look at the offending side where the noise was coming from before things got worse

Hmmmm....

There really wasn't much to this, just clean up everything well and reassemble with the right amount of grease

And to clean the contact surface for the brake pads with a triangular file, fitting without binding now

I'll inspect the other side when I get a chance, but the difference from the brake pedal is night and day already :cool:

joujoujou · 21-03-2019 02:37PM

Had same task in 'rolla months ago. I was able to free up one pin just using vise-grip, but another one was just p.i.t.a. - had to catch pin's end with table vice and use 1 metre long steel bar to sort things. Never had seized pins in older one - planned obsolescence ffs. :mad:

fancy pigeon · 21-03-2019 03:50PM

joujoujou wrote: »

Had same task in 'rolla months ago. I was able to free up one pin just using vise-grip, but another one was just p.i.t.a. - had to catch pin's end with table vice and use 1 metre long steel bar to sort things. Never had seized pins in older one - planned obsolescence ffs. :mad:

Was a common one in the Daily van, they'd seize up after a few months driving round (it did do intergalactic mileage though) regardless of how clean and free they would get they would always give plenty of warning when they were stiffening up. It was a handy way to keep tabs on the condition of the pads and discs at the same time!

rex-x · 21-03-2019 03:58PM

joujoujou wrote: »

Had same task in 'rolla months ago. I was able to free up one pin just using vise-grip, but another one was just p.i.t.a. - had to catch pin's end with table vice and use 1 metre long steel bar to sort things. Never had seized pins in older one - planned obsolescence ffs. :mad:

To be fair its only lack of proper maintenance that makes then seize. Using silicone paste to lube them (as per the factory) and they will stay nice and free, grease (even red rubber) will dry out and make then seize up

joujoujou · 21-03-2019 04:07PM

rex-x wrote: »

To be fair its only lack of proper maintenance that makes then seize. [...]

With all due respect, I have to disagree. As I mentioned, never had that very problem with my old corolla, despite almost half a million kilometres driven and aforementioned pins were never ever looked after!

Older cars were made to last. Newer ones are made to last... warranty period. :P

rex-x · 21-03-2019 04:35PM

joujoujou wrote: »

With all due respect, I have to disagree. As I mentioned, never had that very problem with my old corolla, despite almost half a million kilometres driven and aforementioned pins were never ever looked after!

Older cars were made to last. Newer ones are made to last... warranty period. :P

They were probably lubed properly with silicone and hadnt been messed with by some fella 'greasing them up'

The design of slide pins hasn't changed really in 50 years and while I do agree some modern vehicles arent build like the good old days, slide pins dont fall into that category.....

fancy pigeon · 21-03-2019 04:36PM

rex-x wrote: »

To be fair its only lack of proper maintenance that makes then seize. Using silicone paste to lube them (as per the factory) and they will stay nice and free, grease (even red rubber) will dry out and make then seize up

Never thought of using silicon grease as I have a tin of it on the shelf anyway, but the brakes tend to wear out with me before they get a chance to seize... Brakes don't seize with a vehicle under my ownership

rex-x wrote: »

They were probably lubed properly with silicone and hadnt been messed with by some fella 'greasing them up'

If you can make it out in the 1st pic, the previous ape put moly grease on the pins!

This is it · 21-03-2019 04:43PM

Replaced parking bulbs on the headlights today, absolute bîtch to get at them.

The plastic cover fell off the wing mirror indicator so I picked up a new indicator unit. Three different Allen key sizes, unfortunately I only have two of them. I'll need to pick up a full set before going any further. Could be worse I suppose!

This is it · 22-03-2019 11:08PM

This is it wrote: »

Replaced parking bulbs on the headlights today, absolute bîtch to get at them.

The plastic cover fell off the wing mirror indicator so I picked up a new indicator unit. Three different Allen key sizes, unfortunately I only have two of them. I'll need to pick up a full set before going any further. Could be worse I suppose!

Sorted

Killinator · 23-03-2019 10:58PM

Changed front pads and discs.
From this:

To this:

Gave my wheels a good scrub inside and out while they were off and I'm happy with how it all looks stuck back together:

Edit: no idea why they're uploading all upside down and sideways

James Bond Junior · 23-03-2019 11:09PM

Was only thinking of this car today, I saw it's sister in Childers rd retail park. The sound of them is fantastic.

Killinator · 23-03-2019 11:11PM

James Bond Junior wrote: »

Was only thinking of this car today, I saw it's sister in Childers rd retail park. The sound of them is fantastic.

I was in Childers today so I reckon that was me

James Bond Junior · 23-03-2019 11:14PM

Killinator wrote: »

I was in Childers today so I reckon that was me

Are you female?

Killinator · 23-03-2019 11:21PM

James Bond Junior wrote: »

Are you female?

No, guess it was the other 32 driver so

James Bond Junior · 23-03-2019 11:26PM

Killinator wrote: »

No, guess it was the other 32 driver so

I was thinking that alright... we've had this conversation before! I remember the Gulf Gti in topaz roxboro back in the day and knew it was a lad who owned it!

Killinator · 24-03-2019 02:10AM

James Bond Junior wrote: »

I was thinking that alright... we've had this conversation before! I remember the Gulf Gti in topaz roxboro back in the day and knew it was a lad who owned it!

Ah right, now I remember

joujoujou · 25-03-2019 02:52PM

Plan "A" was as follows - installing 2 gas struts for the bonnet, normal, most popular way. That failed, as E12's bonnet is way too soft and it bent near hinge reinforcements when tried to close it with struts on, so went to Plan "B" and it works!

Not the best solution alright, but IMO the only one possible.

cletus · 26-03-2019 12:55PM

The moment you realise the motor factors gave you the wrong sized rotor...

Toyotafanboi · 26-03-2019 01:14PM

cletus wrote: »

The moment you realise the motor factors gave you the wrong sized rotor...

And the moment after that when you realise it's a brake disc on this side of the Atlantic :pac:

cletus · 26-03-2019 01:22PM

Toyotafanboi wrote: »

And the moment after that when you realise it's a brake disc on this side of the Atlantic :pac:

I shall continue to use Americansims interchangeably, so you can stick it up your bum, Toyotafanboi :P

Anyway, you'd be better served answering my question in the slide pin thread, especially considering it's a Toyota

Toyotafanboi · 26-03-2019 01:27PM

There's a good argument about slide pin grease on the previous page, spilling over onto this one, actually!

wonski · 26-03-2019 06:13PM

NCT on Friday so as a well organized motorist I finally managed to find a time to open the boot in my s40. And I even managed to fix it at the same time.

Since it is old I just put the cables back together and isolated it. I could see signs of same cable being fixed in the past so it is very common.

Also replaced the xenons ballast earlier, well the mechanic did, but I managed to source it at 35 for a pair so happy enough.

Front tires to go in tomorrow or in Thursday and should be good to go for another year

Today I did something to my car (volume 2)

Comments