Change Eircom Phonewatch Alarm Code

Evolution1

Jimski wrote: »

No engineer code, once I type my code it automatically goes to arming

Have you the paper work off the system ? Is it still monitored by phone watch ?

Jimski

Evolution1 wrote: »

Have you the paper work off the system ? Is it still monitored by phone watch ?

I do the paperwork but no longer an eircom customer

altor

Jimski wrote: »

I do the paperwork but no longer an eircom customer

I sent you a P.M. re the code.

Put in your engineer code.
Service menu comes up.
Scroll using the # key to users, press yes.
User codes, press yes.
User 1, press yes.
Input the new user code, press yes.
Verify Code, press yes.
Press quit until you see exit engineering.

Test code and that is it done.

Jimski

altor wrote: »

I sent you a P.M. re the code.

Put in your engineer code.
Service menu comes up.
Scroll using the # key to users, press yes.
User codes, press yes.
User 1, press yes.
Input the new user code, press yes.
Verify Code, press yes.
Press quit until you see exit engineering.

Test code and that is it done.

Thank you so much , it did work

altor

Jimski wrote: »

Thank you so much , it did work

Your welcome, any other problems let us know..

pipman

Hi Altor,

Can you please send code via pm also. It's a HKC unit no longer monitored by Eircom etc.

altor wrote: »

I sent you a P.M. re the code.

Put in your engineer code.
Service menu comes up.
Scroll using the # key to users, press yes.
User codes, press yes.
User 1, press yes.
Input the new user code, press yes.
Verify Code, press yes.
Press quit until you see exit engineering.

Test code and that is it done.

blahblah06

Altor
Sorry to bother u but time to change the code again and can't remember the engineer code and they want €110 call out few to change the code

altor

blahblah06 wrote: »

Altor
Sorry to bother u but time to change the code again and can't remember the engineer code and they want €110 call out few to change the code

Hi blahblah06,

That is no problem, sent you a P.M.

whizbang

Hi Altor, can I trouble you for the installer/dealer code for simon XT. I have all the paperwork, with a heap of different numbers, but none of them work.
thanks

altor

whizbang wrote: »

Hi Altor, can I trouble you for the installer/dealer code for simon XT. I have all the paperwork, with a heap of different numbers, but none of them work.
thanks

Sent you a P.M.

dobsdave

I also have a simon unit, do I have to do a full reset/set-up to add a sensor or other maintenance?
I dont have the engineer code and it is no longer monitored.

Vonwiller

Hi I wonder could you help me with the engineering code- recently cancelled contract and Eircom are saying they need to send an engineer to disconnect system at a charge - would be grateful if u could help me out with how to disconnect but still use as normal alarm . Thanks- meant to say. Model is simon xt

KoolKid

I sent you a PM re the engineer code & the manual.
Hope it helps.;)

Vonwiller

Thanks a million will give it a go

JFKIRELAND

Guys,
I wonder if you can help? I have a Phonewatch simon system (now not monitored). I have just had building works done in the house and 2 of the motion sensors were removed during the build. I put them back up earlier on myself. I am getting lots of tamper and system alerts on the system now.
Is there a code to reset the system to clear these alerts?
Any thoughts or help appreciated.
Thanks

altor

JFKIRELAND wrote: »

Guys,
I wonder if you can help? I have a Phonewatch simon system (now not monitored). I have just had building works done in the house and 2 of the motion sensors were removed during the build. I put them back up earlier on myself. I am getting lots of tamper and system alerts on the system now.
Is there a code to reset the system to clear these alerts?
Any thoughts or help appreciated.
Thanks

Can you press the status button a few times to listen to all events then press disarm.
Now start again pressing the status button to see what the faults are.
Just post what they are and I will tell you how to sort them

JFKIRELAND

Thanks Altor,
I will do it tomorrow evening - Do not want to wake the kids up! (again)
JK

altor

JFKIRELAND wrote: »

Thanks Altor,
I will do it tomorrow evening - Do not want to wake the kids up! (again)
JK

No worries, if you want to turn off the trouble beeps tonight. Drop the front lid, put in your user code, press, delete, option, 01, done

JFKIRELAND

Hi Altor,
If I try to set the alarm now the messages I get are:
System low battery
System Phone Comm Failure and
System Access alarm..

I was getting statuses of the different sensors earlier in the week - no sign now

Many Thanks
JFK

JFKIRELAND

Bump....

altor

JFKIRELAND wrote: »

Hi Altor,
If I try to set the alarm now the messages I get are:
System low battery
System Phone Comm Failure and
System Access alarm..

I was getting statuses of the different sensors earlier in the week - no sign now

Many Thanks
JFK

Hi JFK,

The system low battery is the back up battery in the alarm itself.
System Phone Comm Failure is the alarm trying to communicate with P.W. This is resolved by deleting the numbers the system dials out on.
System Access alarm is you after opening the control panel.
This should clear once you close up the panel.

I have sent you a P.M. re the engineer code.

Henry2010

Hi - it has been a while since I used my alarm - I havent lived in my house for a while but am back now and have forgotten my code. Does anybody know how I can reset it/retrieve it? I do not have a remote control. Have just been on to eircom who will only send an engineer at a cost of €149.00. Please help - thanks

Bulmers

Hi Altor,

could you send me the eng code for changing alarm code, one of the buttons on my pad isn't working so well so would like to change it - just want to change the 4 digit exit / entry code

cheers

altor

Henry2010 wrote: »

Hi - it has been a while since I used my alarm - I havent lived in my house for a while but am back now and have forgotten my code. Does anybody know how I can reset it/retrieve it? I do not have a remote control. Have just been on to eircom who will only send an engineer at a cost of €149.00. Please help - thanks

What system have you installed?

altor

Bulmers wrote: »

Hi Altor,

could you send me the eng code for changing alarm code, one of the buttons on my pad isn't working so well so would like to change it - just want to change the 4 digit exit / entry code

cheers

If its the Simon system. Drop the front lid and enter your user code.
Press, add. Then press access till you hear master code, then press done. Enter the new code then press done again.

robertfarrell

is there any chance of getting the eng. code for the simon wireless panel.
thanks

we have just moved into a rented house. we have no codes or paperwork.
is there anything we can try to get it working.
thanks in advance

KoolKid

I sent you a PM re the manuals and the engineer code.

altor

robertfarrell wrote: »

is there any chance of getting the eng. code for the simon wireless panel.
thanks

we have just moved into a rented house. we have no codes or paperwork.
is there anything we can try to get it working.
thanks in advance

If you have still not got into this system send me a P.M.
On the Simon there is a sneaky way to get the code if not turned off

ALS

is there any chance of getting the eng. code for the simon wireless panel.
thanks

we have an old disconnected system that I want to try and install it has been unplugged in the shed for the past 12 months we have no codes or paperwork.
is there anything we can try to get it working.
thanks in advance, or can someone give me a price to install ? 3 motion sensors and 3 door sensors

pictures inc thanks in advance

KoolKid

Sent you a PM