Advertisement
If you have a new account but are having problems posting or verifying your account, please email us on hello@boards.ie for help. Thanks :)
Hello all! Please ensure that you are posting a new thread or question in the appropriate forum. The Feedback forum is overwhelmed with questions that are having to be moved elsewhere. If you need help to verify your account contact hello@boards.ie

Tech Support for Aritech Alarm systems

Options
1…101112131416»

Comments

  • Options
    #452
    Mycro
    Registered Users Posts: 152 ✭✭Mycro


    Hi Koolkid,

    Output 6 rings the outside Bell only. However, my apologies. I must have been hearing things. The walk test rings only the internal!

    Thank you :-)


  • Options
    #453
    KoolKid
    Moderators, Home & Garden Moderators, Technology & Internet Moderators Posts: 24,789 Mod ✭✭✭✭KoolKid


    Thats as it should be.;)


  • Options
    #454
    wpd
    Registered Users Posts: 492 ✭✭wpd


    Hi hope someone can help

    I have an Aritech alarm and the back door alarms in part guard mode when opened however in full alarm mode it doesnt alarm at all

    i dont think it is inhibited

    any advice

    (i have engineers code)


  • Options
    #455
    altor
    Registered Users Posts: 11,640 ✭✭✭✭altor


    wpd wrote: »
    Hi hope someone can help

    I have an Aritech alarm and the back door alarms in part guard mode when opened however in full alarm mode it doesnt alarm at all

    i dont think it is inhibited

    any advice

    (i have engineers code)

    I would expect it to alarm in full alarm if its working in part guard.
    Is this device on its own zone?

    www.altor.ie



  • Options
    #456
    wpd
    Registered Users Posts: 492 ✭✭wpd


    no its on a zone with windows


  • Advertisement
  • Options
    #457
    altor
    Registered Users Posts: 11,640 ✭✭✭✭altor


    wpd wrote: »
    no its on a zone with windows

    Do these windows alarm in full alarm?

    www.altor.ie



  • Options
    #458
    wpd
    Registered Users Posts: 492 ✭✭wpd


    I will try it and let you know
    will try it in walk test mode


  • Options
    #459
    altor
    Registered Users Posts: 11,640 ✭✭✭✭altor


    wpd wrote: »
    I will try it and let you know
    will try it in walk test mode

    Try it with the system on part set, then in full set.
    If it works in part set it should work in full alarm mode.
    If it was the other way around it would be because the zone may be inhibited in part set. Full alarm sets everything.

    www.altor.ie



  • Options
    #460
    FRANK A
    Registered Users Posts: 9 ✭FRANK A


    hi , having problems with my aritech 350 AGAIN,,, message on key pad .... call alarm co,...51. can anybody help please...


  • Options
    #461
    paulrice1811
    Registered Users Posts: 5 ✭paulrice1811


    Hi all
    I have an Aritech CP32 alarm and it has recently started displaying the letter " C " and will not allow the alarm to be set.
    This letter is not in the troubleshooting guidance booklet for the alarm.
    Any ideas ?


  • Advertisement
  • Options
    #462
    altor
    Registered Users Posts: 11,640 ✭✭✭✭altor


    FRANK A wrote: »
    hi , having problems with my aritech 350 AGAIN,,, message on key pad .... call alarm co,...51. can anybody help please...

    If you know who installed the system send me a P.M. and I will check my list for a code for you.

    www.altor.ie



  • Options
    #463
    KoolKid
    Moderators, Home & Garden Moderators, Technology & Internet Moderators Posts: 24,789 Mod ✭✭✭✭KoolKid


    An engineer code is not required to clear the call alarm company messages.
    Sent information to FrankA
    If anyone else wants correct instructions on resetting this please PM me.
    This general thread has served its purpose from its origination in the Electrical forum.
    Closed.


This discussion has been closed.
Advertisement