Advertisement
If you have a new account but are having problems posting or verifying your account, please email us on hello@boards.ie for help. Thanks :)
Hello all! Please ensure that you are posting a new thread or question in the appropriate forum. The Feedback forum is overwhelmed with questions that are having to be moved elsewhere. If you need help to verify your account contact hello@boards.ie
Hi there,
There is an issue with role permissions that is being worked on at the moment.
If you are having trouble with access or permissions on regional forums please post here to get access: https://www.boards.ie/discussion/2058365403/you-do-not-have-permission-for-that#latest

condensing oil boiler upgrade

2»

Comments

  • Posts: 0 [Deleted User]


    heinbloed wrote: »
    This is a technical forum,.

    Yep, and what are you qualified in ?


  • Registered Users, Registered Users 2 Posts: 1,632 ✭✭✭heinbloed


    Gary71 interferes in this technical discussion with the unqualified remark:
    Yep, and what are you qualified in ?

    I'm qualified in revealing lies, Gary71.



    See this discussion here.


  • Posts: 0 [Deleted User]


    heinbloed wrote: »
    Gary71 interferes in this technical discussion.
    no, this discussion started out with a simple question which by rights should have been easily answered.


  • Hosted Moderators Posts: 3,496 ✭✭✭DGOBS


    real eyes
    realize
    real lies


  • Closed Accounts Posts: 8,156 ✭✭✭Iwannahurl


    gary71 wrote: »
    I know of installations where weather compensation was fitted only as a add on and they reduced their fuel costs so they do serve a purpose( and no I don't have a linky)




    This discussion is getting rather reizbar(?). I don't know whether it's a recurring issue in this forum, but I think it's obscuring the central question.

    If I were installing a condensing boiler and associated technology I would want to be certain that (a) my fuel consumption would be reduced, (b) that the improved technology gave me a higher level of control and hence 'comfort', and (c) that the upgrade would pay for itself in a reasonable time period.

    In the examples you refer to above, how were the cost savings evaluated?




    .


  • Posts: 0 [Deleted User]


    Iwannahurl wrote: »

    In the examples you refer to above, how were the cost savings evaluated?

    It manly from the reduced fuel costs, the main body of people I would be talking to is other gas engineers.

    Further info on weather compensation:
    http://www.greensystemsuk.com/Solar_Hot_Water_pdfs/Viessmann-Weather-Compensation-Controls.pdf


  • Posts: 0 [Deleted User]


    Iwannahurl wrote: »

    If I were installing a condensing boiler and associated technology I would want to be certain that (a) my fuel consumption would be reduced,


    (b) that the improved technology gave me a higher level of control and hence 'comfort', and (c) that the upgrade would pay for itself in a reasonable time period.

    In the examples you refer to above, how were the cost savings evaluated?




    .

    I think points A and B go hand in hand and lead to point C.


  • Closed Accounts Posts: 8,156 ✭✭✭Iwannahurl


    Perhaps gas consumption, if metered, can be monitored more closely than, say, kerosene home heating oil?

    It's certainly an alluring prospect, but I would need to see independent evaluation showing the potential benefits for your average homeowner. Such as myself, with (so far) a standard oil-fired boiler and 2-zone system.

    The Viessmann blurb makes weather compensation look good, but the alleged benefits seem to rely a little too much on human behaviour for my liking:

    The chances are that at this stage, the householder will be feeling the cold and will turn the thermostat up even further - wasting even more fuel.

    If the outside temperature rises, the boiler will not respond until the rooms have become uncomfortably warm - so in addition to adjusting the thermostat, there’ll probably be the temptation to open some windows, releasing more heat and wasting more energy.


  • Registered Users, Registered Users 2 Posts: 1,632 ✭✭✭heinbloed


    Gary71 is asked about the cost savings associated with the co-installation of condensing boilers with weather compensation units.
    In the examples you refer to above, how were the cost savings evaluated?

    and answers
    It manly from the reduced fuel costs, the main body of people I would be talking to is other gas engineers.

    Reduced fuel costs are not the same as cost savings, Gary71.
    Anyhow:

    How much was saved with what meassures, due to which influences ?

    How much of the (maybe achieved) fuel costs were due to fuel replacing (other, cheaper fuels used instead of gas - the open fire, stove, the OAP bonus for coal and gas etc.) how much was due to changed consumer behaviour, how much was due to changed weather pattern, how much was due to the new boiler, how much was due to better in-house controls, how much was due to the weather/changed heating degree days/passive solar gain? How much was due to the weather compensation?

    How many recorded cases are there to draw data from?


  • Advertisement
  • Registered Users, Registered Users 2 Posts: 1,632 ✭✭✭heinbloed


    Iwannahurl asks :
    Perhaps gas consumption, if metered, can be monitored more closely than, say, kerosene home heating oil?

    Meters meassuring boiler consumption are available at the plumbing shop. There should be no technical problem meassuring the oil consumption of a boiler.


  • Posts: 0 [Deleted User]


    Don't fit anything you don't agree with it's not rocket science;), I'm not a flag waver for weather compensation or condensing boilers, its not my job or calling to convince anybody of anything, I have a opinion it's based on 25 years working in the industry and I'm qualified(well I have the papers anyway:cool:), I'm not trying to sell any idea or control system, the things i'v advised are things I'd happily do in my own house, if that's not accepted, fine, I don't mind:D


  • Posts: 0 [Deleted User]


    Iwannahurl wrote: »
    but the alleged benefits seem to rely a little too much on human behaviour for my liking:

    [

    you can say that about any control system, most home owners don't know or care to know where their filling loop is or take responsibility for basic heating system controls.


  • Posts: 0 [Deleted User]


    heinbloed wrote: »
    Gary71 is asked about the cost savings associated with the co-installation of condensing boilers with weather compensation units.



    and answers



    Reduced fuel costs are not the same as cost savings, Gary71.
    Anyhow:

    How much was saved with what meassures, due to which influences ?

    How much of the (maybe achieved) fuel costs were due to fuel replacing (other, cheaper fuels used instead of gas - the open fire, stove, the OAP bonus for coal and gas etc.) how much was due to changed consumer behaviour, how much was due to changed weather pattern, how much was due to the new boiler, how much was due to better in-house controls, how much was due to the weather/changed heating degree days/passive solar gain? How much was due to the weather compensation?

    How many recorded cases are there to draw data from?

    Sorry, I feel bad now I didn't ask any of that, they were just so happy their bills went down I must have forgot :D


  • Registered Users, Registered Users 2 Posts: 145 ✭✭Plombier


    Heating Systems.

    A building heating system is designed to provide full heating on design day; in practice an additional margin is allowed to provide extra power during boost period of intermittent heating. The capacity of the heating is therefore greater than required for operation in all but the coldest conditions. For buildings heated by conventional a radiator system, operation during mild weather with the flow temperature at full design value, typically 80C, results in control problems high temperature swings and consequential discomfort; it also results in wasteful heat loss from hot water circuits and plant.

    Two-position (on/off) control

    In this mode, the controlled device gives either maximum or minimum output, typically on and off. To prevent a high frequency of switching, with attendant wear on plant and equipment, it is necessary for a switching differential between the switching on and the switching off of the controlled device. With the heating on, the space temperature rises until the sensor output exceeds the set point. The heating then switches off and stays off until the temperature falls through the differential and reaches the lower limit, whereupon it switches back on and the cycle repeats.

    The room temperature continues to rise for a time after the heating system has been switched off, this is caused by the fact that the radiators still contain water at full design temperature.
    The room temperature continues to fall for a time after the heating system has been switched on, this is caused by the fact that the radiators now contain water well below the temperature required.

    Two position control results in a swing in temperatures about the set point and a mean temperature that that normally lies below the set point with the consequential discomfort and wastage as mentioned above.

    Weather compensation.

    Compensation control requires a continuously variable output of the controlled device. The controller produces an output that is proportional to the error signal; i.e. the difference between the value of the controlled variable and the set point. The control output increases from 0 to 100% as the input falls from the set point. Unlike on-off control there are no swings in temperatures about the set point but a steady state condition prevails, increasing comfort and minimising wasteful heat loss from hot water circuits and plant.

    Compensation control allows the whole building to be controlled as one unit, or as a limited number of zones, thus eliminating the need to provide a large number of separate space controls. It has the added advantage of limiting heat loss in the event of increase load, e.g. if windows are left opened. A practical addition to compensation control is the addition of Zone Trim. The standard weather compensation circuit is used, with a zone trim applied to the compensated water flow temperature. The trim
    modifies the set point by a margin proportional to the difference between the measured zone temperature and the desired set point.


    Figures.

    Energy usage based on degree hours and calculated Building Base Temperature.

    Energy / K Casual Heating Overall Mean Base Hourly Days Energy
    U kW/K^-1 Gains kW SP Efficiency Temperature Tempeaature Monthly kWh/hour
    1.00 1.50 21.00 0.75 7.00 19.50 12.50 16.67
    0.50 1.50 21.00 0.75 7.00 18.00 11.00 7.33




    Shown above is the hourly energy demand at row 100% load and in row two 50% load.

    The heat output from a radiator is proportional to the 1.3 power of the difference between the mean radiator and the room temperature (deltaT) it is not a matter of simply halving the flow temperature to get half the power, in this example the flow temperature for a 50% load is 48.0C.

    DeltaT 82.5C flow 21C room drop across rad 11C = 55.0C (No condensing)
    DeltaT 48.0C flow 21C room drop across rad 10C = 32.5C (Full condensing)


    The column Building Base Temperature column and Energy usage colum shows the point.


  • Registered Users, Registered Users 2 Posts: 800 ✭✭✭oldsmokey


    Oh Lordy, seems I've opened a little hornets nest here - thanks everyone for the input - theres a lot of opinion out there! I reckoned i was doing the right thing in going for a condensing boiler, but even that appears to be a moot point now...I guess its time tocall in someone who knows his heating onions and let him size up our set-up...but i know a little more now at least..


  • Advertisement
  • Closed Accounts Posts: 8,156 ✭✭✭Iwannahurl


    IMO none of these things can be taken for granted.

    On the basis of what I have read here, I am certainly tempted to consider upgrading my boiler and controls. However, as always, I will carefully research all the details first.

    Let us know how you get on! If possible, and if you go for the condensing option plus additional features like weather compensation, it would be good to have accurate before-and-after information on fuel consumption.


  • Registered Users, Registered Users 2 Posts: 145 ✭✭Plombier


    As a simple explanation imagine two identical cars on a journey from Dublin to Cork.

    Car one has its accelerator removed and an automatic on/off switch fitted in its place (in a heating system this is a thermostat), when you start the car the switch automatically goes to the on position and the car will accelerate at maximum acceleration until it reaches 100 kph (in a heating system the set point) and at this point it switches itself off until its speed drops below 75kph(in a heating system the set point less the switching differential) where it switches on again and continuously repeats the cycle all the way to Cork with the car engine going from full acceleration to no acceleration regardless of the effort required to propel the car, not going to be very economical.

    Car two on the other hand has cruise control fitted and is set to maintain a steady speed of 75kph(in a heating system the set point), the cruise control continuously monitors the speed and adjusts the acceleration according to the effort required to propel the car forward (in a heating system this is weather compensation).
    If the car travels uphill the cruise control increases acceleration (in a heating system this is cold weather).
    If the car travels downhill the cruise control decreases acceleration (in a heating system this is mild weather).
    There may be one or two miles on the journey where maximum output from car two is required (in a heating system these are design conditions).

    Now if the cars speed can be kept below 80kph the engine efficiency can be increased by 10% - 15%(in a heating system this is condensing mode).

    Car one will possibly drop below 80kph for a very short while when the switch goes from the off to on position, but will quickly accelerates beyond it again (in a heating system very little condensing).

    Car two on the other hand will always keep the acceleration to a minimum thereby maintaining maximum efficiency at all times (in a heating system maximum condensing mode).


  • Closed Accounts Posts: 8,156 ✭✭✭Iwannahurl


    I'll have to have a closer look at that CIBSE literature for a start.

    Certainly it has always bugged me that my central heating system keeps kicking in even when the room temperature is adequate given the outside temperature. It seems that the reading on the zone/room thermostat is not an absolute, whereas I expect 18 or 22 degrees to be just that, within reason! It also drives me mad that the thermostat often comes on when I turn it down!

    I try to reduce short cycling, or whatever it's called, by keeping the boiler thermostat low. No need for boiling water in the taps especially, IMO.


  • Registered Users, Registered Users 2 Posts: 800 ✭✭✭oldsmokey


    Thanks Plombier - the analogy makes sense - it also appears to me that its probably worth going the extra few quid on the condensing boiler (given the govt grant) , even if it wont be in condensing mode all the time..true?
    Is there a heat-merchants or supplier who you could recommend in the North Cork / Cork city / East Kerry area? Someone without an 'axe to grind'?...pm me if you wish...With regard to installation, theres a local plumber who's living nearby, and we therefore are kind of obliged to use, I just dont know how 'tuned in' he is - could a reasonably competent man fit the thing or is it better to get a 'specialist'?..I know, lotsa questions, but its nice to get it right first time..thanks again.....


  • Hosted Moderators Posts: 3,496 ✭✭✭DGOBS


    even when the boiler is not in condensing mode, it is still more efficient that a standard boiler as it has more surface area exposed to the flue gases (and hence less loss)


  • Advertisement
  • Closed Accounts Posts: 8,156 ✭✭✭Iwannahurl


    What about the costs of a new (replacement) boiler?

    Roughly how much for unit and installation?

    How long to recoup costs in fuel savings?


  • Registered Users, Registered Users 2 Posts: 1,632 ✭✭✭heinbloed


    DGOBS writes:
    even when the boiler is not in condensing mode, it is still more efficient that a standard boiler as it has more surface area exposed to the flue gases (and hence less loss)

    As there any independant document anywhere available which says so ? Source? Link?


  • Registered Users, Registered Users 2 Posts: 1,632 ✭✭✭heinbloed


    Iwannahurl wrote:
    What about the costs of a new (replacement) boiler?
    Roughly how much for unit and installation?

    It depends what you want and where you buy it, as usual.
    How long to recoup costs in fuel savings?

    This depends on replacement costs, future fuel and maintenance costs, life time expection and previous costs of the old system.


  • Registered Users Posts: 36 stiophan


    MOD NOTE

    deleted. Poster replying to a very old thread.

    Post edited by Wearb on


Advertisement