How to disable alarm sensor?

Meeoow · 16-04-2025 06:31PM #1

I am getting work done on my house and builder is knocking down outside wall. Can someone advise me how to disable one window and a back door sensor on a HKC secure watch panel? I don't have an eng code. Thanks

altor · 20-04-2025 12:21PM

https://www.boards.ie/discussion/comment/123373928#Comment_123373928

If it works why replace.

You can either extend the cable or else you can run new cable from control panel to the new door

altor · 17-04-2025 04:18PM

https://www.boards.ie/discussion/2058406417/how-to-disable-alarm-sensor

Are these the only 2 on the loop back to the panel?

If so you could disconnect at the control panel and close of the zone.

If not.

Take off the sensor and join the cables together. eg, alarm to alarm, tamper to tamper.

Also, take a few photos before disconnecting the wires.

Meeoow · 17-04-2025 07:49PM

Not sure Altor. I'll look the weekend. Thanks

Meeoow · 19-04-2025 01:48PM

Hey Altor. Looking at alarm now. Can I remove sensor with alarm powered on? Not enabled, but mains on?

Paul.kavanagh · 19-04-2025 08:01PM

yes you can , alarm may sound , put your code in to disarm the system upon activation. remember to take the pictures of the wiring first.

altor · 20-04-2025 11:50AM

https://www.boards.ie/discussion/comment/123371464#Comment_123371464

Did you work out what devices are on the zone?

Meeoow · 20-04-2025 12:01PM

No Altor. The window is zone 5 and door is zone 1. The builder removed them cause he knocked the wall. I took the magnet off the door and cable tied it to the sensor. And both are cable tied to the rafters at the minute, so I can use the alarm.

altor · 20-04-2025 12:09PM

https://www.boards.ie/discussion/comment/123373900#Comment_123373900

Zone 1 would usually be an entry exit point on the alarm so that will be needed in the future unless you have a different entry point.

Meeoow · 20-04-2025 12:13PM

https://www.boards.ie/discussion/comment/123373922#Comment_123373922

Makes sense. I am not sure if cable will reach new door, as it's a few feet out. I'll try to salvage it. If it can be re used, do ye recommend this, or should I upgrade? Tbh, the alarm works ok, and seems to be a good deterrent, so not mad about upgrading, if there's no benefit.

Meeoow · 20-04-2025 12:29PM

A few posters advised me here. Many thanks. This has to be one of the best forums on boards!

Meeoow · 01-05-2025 09:59AM

Hi again! I have a secondary alarm keypad at the back door of the house. There is on cable going to it. It can be used to arm and disarm the alarm. Can I disconnect it? There are just 4 wires on the cable.

altor · 01-05-2025 10:28AM

https://www.boards.ie/discussion/comment/123407385#Comment_123407385

Yes but if the keypad is IDed to the system you would need to remove it in the device menu.

Another option, if possible, would be to use it in a bed room if you dont have engineer access to do same.

Meeoow · 01-05-2025 10:31AM

Ok. It probably is IDed to system, cause main keypad is giving Comms error. I can move it then. Not a biggie. Cheers Altor!

altor · 01-05-2025 10:33AM

https://www.boards.ie/discussion/comment/123407513#Comment_123407513

No problem at all

How to disable alarm sensor?

Best Answer

Answers