Advertisement
Help Keep Boards Alive. Support us by going ad free today. See here: https://subscriptions.boards.ie/.
https://www.boards.ie/group/1878-subscribers-forum

Private Group for paid up members of Boards.ie. Join the club.
Hi all, please see this major site announcement: https://www.boards.ie/discussion/2058427594/boards-ie-2026

Chain Saw Chat

Options
11718192022

Comments

  • Registered Users, Registered Users 2 Posts: 6,753 ✭✭✭bassy


    Guys I've a sthil ms181 and it was left it to be repaired few weeks back and I got it back and it's not running right at all,gets bogged down and chain stops when trying to cut timber and it gives loud rev for a few seconds and goes all over the shop with low and high revs and takes a age to try cut logs.

    Has a new chain,so no probs there.


    Any ideas what it might be,when I picked it up off the so called repair shop one guy said that carb is not great in that saw,sure if he taught that why not replace it and I said it to him,he says oh take a few weeks to get one.WTF like................


    You guys think it's the carb??.



  • Registered Users, Registered Users 2 Posts: 870 ✭✭✭divillybit


    The seals on the crank shaft may be leaking. If they are leaking that can affect the carb as it's the vacuum /pressure change in the crankcase as the piston moves that powers the carburettor to suck petrol from the fuel tank and inject it to the cylinder.

    A way to test those seals is using brake cleaner spray, I got some from my local screwfix store. Spray it in around the clutch and starter cord when the saw is running and if it stops the seals are leaking.

    Found this video below to be good. Probably as handy to buy a new carb than redo the diaphragm on the old one. It's a bit fiddly to replace them but not a big job either.

    https://youtu.be/_5n7zUdJt6U



  • Registered Users, Registered Users 2 Posts: 6,753 ✭✭✭bassy




  • Registered Users, Registered Users 2 Posts: 13,158 ✭✭✭✭blue5000


    Lidl have their battery powered chainsaw in again, €110 without batteries or chargers.

    They use 2 x 20v batteries, if you don’t have them already it puts the cost up a good bit as I think the batteries are €40 each. Get the 4 ah ones, not the 2 ah batteries, much better for power hungry jobs.

    If the seat's wet, sit on yer hat, a cool head is better than a wet ar5e.



  • Registered Users, Registered Users 2 Posts: 6,753 ✭✭✭bassy


    How many cuts on a fully charged 4ah ??



  • Advertisement
  • Registered Users, Registered Users 2 Posts: 16,135 ✭✭✭✭Discodog




  • Registered Users, Registered Users 2 Posts: 374 ✭✭Vittu


    Husqvarna chainsaw leaks oil when sitting idle. Any ideas on how to stop this leak?



  • Registered Users, Registered Users 2 Posts: 870 ✭✭✭divillybit


    There probably is a screw to adjust the oil flow to the chain, so that may need adjustment but it will be letting out some oil even when idling which is normal



  • Registered Users, Registered Users 2 Posts: 374 ✭✭Vittu


    Hi, thanks for your response. I phrased it wrong originally. When chainsaw is not been used as in the shed or back of van it leaks oil and is a mess. Trying to figure out how to stop this.



  • Registered Users, Registered Users 2 Posts: 13,158 ✭✭✭✭blue5000


    Looks like F R Jones across the pond have ceased trading.

    If the seat's wet, sit on yer hat, a cool head is better than a wet ar5e.



  • Advertisement
  • Registered Users, Registered Users 2 Posts: 6,753 ✭✭✭bassy


    hi i bought a new carb and fitted it,but a friend reckons that the crankshaft seals are leaking or letting air in.cause it be running fine then for a bit its like sucking air in,if you get what i am trying to say.

    i wonder where would i get 2 quality seals online and would it ne good to change the bearings to??.


    now i,ve never done a job like this before as in i think the whole saw comes apart,is it a manageable job.i replaced the carb etc but i think thats a lot easier.



  • Registered Users, Registered Users 2, Paid Member Posts: 609 ✭✭✭coillsaille


    Hi folks, only a domestic user here who's a bit confused due to getting different air filters delivered after ordering online. Would appreciate an answer. Which one should be used in this country with a Stihl ms291, A or B?


    Post edited by coillsaille on


  • Registered Users, Registered Users 2 Posts: 870 ✭✭✭divillybit


    A would probably be a better one in ways as it would have more surface area and probably take longer to block but either filter look good. I've an ms250 and would like to upgrade the air filter set up on it. The standard air filter isint great



  • Registered Users, Registered Users 2, Paid Member Posts: 4,125 ✭✭✭50HX


    Anyone recommend a battery chainsaw for light farm work, handy sized stuff to be cut for the stove.

    My ms170 sthil has died 😢



  • Registered Users, Registered Users 2 Posts: 590 ✭✭✭n1st


    I have a Bosch short battery chinsaw. Very handy. No issues. Can cut through any branches. Can also work single handed



  • Registered Users, Registered Users 2, Paid Member Posts: 35,689 ✭✭✭✭listermint


    I'd probably be inclined to go Makita. https://www.powertool.ie/p/makita-duc256z-10-250mm-twin-18v-lxt-brushless-chainsaw-3_8-pitch-body-only/duc256z

    this is body only needs twin 18v batteries.



  • Registered Users, Registered Users 2 Posts: 603 ✭✭✭timfromtang


    This is a top handle saw, NOT SUITABLE FOR USE ON THE GROUND meant for use by trained climbers.

    For ground use a rear handle chainsaw should be used.

    just my 2 cents

    tim



  • Registered Users, Registered Users 2, Paid Member Posts: 4,125 ✭✭✭50HX


    Cheers tim



  • Registered Users, Registered Users 2 Posts: 603 ✭✭✭timfromtang


    No Worries,

    if you read the description carefully it mentions this on the 4th line of the description

    "Ideal for tree care - to be used by professional tree surgeons"


    tim



  • Registered Users, Registered Users 2 Posts: 603 ✭✭✭timfromtang


    The Husqvarna electric saws have a good reputation, although you'll be throwing a good few pound at it. Any reason you are not going for another small petrol saw?

    tim



  • Advertisement
  • Registered Users, Registered Users 2, Paid Member Posts: 4,125 ✭✭✭50HX


    Just looking at the options considering I don't have that much work for a saw, an hour here & there, fuel goin old in the tank etc



  • Registered Users, Registered Users 2 Posts: 13,158 ✭✭✭✭blue5000


    No regrets with the parkside/lidl one above. Get the bigger 4ah batteries though. I bought it just to see what a battery saw was like before spending big bucks on the 'traditional' chainsaw brands. I'd be happy to stick with this one. However I think the later versions have a shorter bar and the batteries are more expensive too.

    Don't get the 2ah batteries though. We cut a wheelie bin full of 4-5 inch ash on one charge of the 2ah batteries.

    If the seat's wet, sit on yer hat, a cool head is better than a wet ar5e.



  • Registered Users, Registered Users 2 Posts: 239 ✭✭tikka16751




  • Registered Users, Registered Users 2, Paid Member Posts: 4,125 ✭✭✭50HX


    Good option, I've to go shopping for a saw

    Anyone here with a battery one for a while now



  • Registered Users, Registered Users 2 Posts: 16,135 ✭✭✭✭Discodog


    Apparently if you use the Stihl Ultra 2 stroke oil is keeps the fuel good for a couple of years & prevents carb damage. Much cheaper than aspen



  • Registered Users, Registered Users 2 Posts: 16,135 ✭✭✭✭Discodog


    I was going to suggest Lidl Parkside. Lots of good revues.



  • Registered Users, Registered Users 2 Posts: 239 ✭✭tikka16751




  • Registered Users, Registered Users 2 Posts: 73 ✭✭accidental forester


    Back to the battery saw question: We've used a Makita DUC353PG2 (or DUC353Z without batteries) for the last four years with no major problems. It's a 2 battery (36v) saw and lasts quite well. My only two gripes are (1) you have to press the ON button again after a few seconds of non-operating. (2) The some of the chain tensioning components are plastic. Sufficient tension can be achieved but it feels a bit flimsy.



  • Registered Users, Registered Users 2 Posts: 235 ✭✭OrangeBadger


    Can anyone suggest a good tool for sharpening chains? Last time I tried the chain ended up even blunted :(

    Recently purchased two saws and want to take care of them properly from day one

    STIHL MS 181 C-BE Ergo Start Chainsaw 16"

    Husqvarna 120 mark ll

    I wouldn't be doing a massive amount of work and will usually be doing it with timber in a log clamp



  • Advertisement
  • Registered Users, Registered Users 2 Posts: 16,135 ✭✭✭✭Discodog


    This is the best & so easy to use

    But you need to get the right one for your chain.



Advertisement
Advertisement