CASE IH 956 full rebuild

greendragon3

hi all , bit of a change from the zetors this time , we have decided to take on a project for my wife's uncle , he has been asking me to do this for quite a while so once we got the workshop empty we bit the bullet and got started , bear in mind she is very crispy having sat out beside the sea for most of her life , it has been mainly used to drive a post driver for the longest time but is mechanically perfect and going like an empty train , nay way im raveling again ill let the pictures do the talking .

greendragon3

greendragon3

greendragon3

greendragon3

Desolation Of Smug

Rippin in there GD! Nice one!

Slideways

Makes a change from the Zetors

greendragon3

back again , thanks for all the comments and tips , well the cutting and measuring and bracing has started in earnest , we found out our first fatal mistake this morning , the cab section we got is off an earlier model ( obviously red and white ) but also a smaller model , maybe an 856 or something , anyway the rails underneath the cab are smaller and wont line up but we have come up with a cunning plan ( all will be revealed soon ) , anyhow some pics of todays progress .

greendragon3

well guys back again after a frantic day , we started off this morning by rolling out the tractor for a good dousing in jizer and a decent steam off afterwards

greendragon3

then it was time to tackle the cab head on , took a bit of lining up and tweaking but we got it to fit finally and welded her up , looks good i think ,

greendragon3

the old bit was very shook when we finally got it out and is only fit for the scrap pile , the difference in the two part is obvious in these pictures , the main chassis rails underneath the cab are actually wider on the 956 cab to allow for the wider transmission im guessing but we managed to get it line up and now you wouldn't know the difference .

greendragon3

and here are a couple of pictures of it all welded up and in place and a lot stronger than what was there .

greendragon3

and finally some pictures of the new mudguards i got for her

Desolation Of Smug

GD, maybe turn up the flow on your gas a fair bit, turn the power up a little bit and balance the wire-feed rate accordingly - and grind back the paint another 5-10mm where you're welding - it'll leave the welds flatter, smoother and stronger, less burning and blackening and less paint contamination in the welds - run the welds as a series of looping eeeee's - plus it'll smell a lot nicer in the workshop..feckin lovely work though, your builds are one of the best things on Boards as far as I'm concerned!

greendragon3

thanks for the tips DOS , the brother does the welding and our mig blew up last week so he is using a borrowed one from a mate , i could hear him cursing it every few minutes because he couldn't get the mix set up right on it but im not trying to make excuses , i know where you are coming from because it is left to me to clean up all the welds and tidier work would be a lot easier to clean and prep for paint . ah well i will have to get more flap discs !!

greendragon3

back with a small update , we were busy all week with other projects and running and racing to different things so not much has been done really , we started to mock up the new bonnet which is a bit shorter than the original one ( all i could get at the time ) so we will have to chop the remaining good bit out of the original one and make it fit , we also had to move the hole for the exhaust as it was off by about an inch , some pics

greendragon3

on a side not we were invited to the zetor roadshow in Jacobs in enniscrone last Thursday and we had a great ould day looking at all the new stuff on display , my phone went on the blink so i only managed two pics of the new 150 but she is an impressive beast for sure , we also had a local tractor run today and we manged to secure a brand new proxima from Jacobs for the day , the ould fella was chuffed to bits and we couldn't get him out of it all day , again i only managed a few pics as i was flat out driving all day .

greendragon3

oh and we managed to get some of the cab sanded down and ready for a small bit of cosmetic work and prepping for paint ,

greendragon3

ok its update time again , things have been a bit slow in the workshop the last few days but we got back into it yesterday and did a bit of a mock up of some of the parts to make sure everything was lining up properly before we start to paint , so it was back on with the cab and the newly stretched bonnet .

greendragon3

greendragon3

we also got stuck into the twisted steps which had had a few belts over the years so we cut and straightened them .

greendragon3

small update guys . been busy rubbing down and prepping for paint etc the last few weeks , we are nearly there thank god , just starting to apply the primer now .

greendragon3

bit more progress today .

greendragon3

some amount of rubbing down gone into the bugger , we were adding up today that we have used / burnt out 15 of the little 4" wire brush heads for the small grinder and 6 of the big ones for the 9" grinder ,
not to mention flap discs and sand paper ,

spent the whole day today on the four wheels , split the centers out of them first and wire brushed them all then cleaned them down with a finer grit sand paper by hand then cleaned them with panel wipe and masked off the tyres ready for primer and paint tomorrow ,

two different colors like original , hard work but hopefully it will all be worth it , no pictures yet because my phone is full so im waiting on the brother send me some from his phone .
:fighting::fighting:

colm_mcm

Loving the build so far. Missing a few of the photos though, getting a "photo not found" icon?

greendragon3

thanks colm , dont know whats up with the photos , i just went through them all and i can see them so not sure whats going on there .

colm_mcm

Just realised its your signature!

greendragon3

wheels getting some silver and other parts in primer ...

randy hickey

Ah feck it!
Just saw this thread for the first time and now I'm hooked!


Thread followed.

greendragon3

randy hickey wrote: »

Ah feck it!
Just saw this thread for the first time and now I'm hooked!


Thread followed.

cheers lad , more updates and pictures to follow soon , the brother was away on a stag so there was nothing done last weekend !!!

greendragon3

black is done now time to start re-assembly .