Advertisement
If you have a new account but are having problems posting or verifying your account, please email us on hello@boards.ie for help. Thanks :)
Hello all! Please ensure that you are posting a new thread or question in the appropriate forum. The Feedback forum is overwhelmed with questions that are having to be moved elsewhere. If you need help to verify your account contact hello@boards.ie
Hi all! We have been experiencing an issue on site where threads have been missing the latest postings. The platform host Vanilla are working on this issue. A workaround that has been used by some is to navigate back from 1 to 10+ pages to re-sync the thread and this will then show the latest posts. Thanks, Mike.
Hi there,
There is an issue with role permissions that is being worked on at the moment.
If you are having trouble with access or permissions on regional forums please post here to get access: https://www.boards.ie/discussion/2058365403/you-do-not-have-permission-for-that#latest

Heat Pumps - post here.

1…910121415…73

Comments

  • #552
    335i
    Registered Users Posts: 11 ✭335i


    Wegian wrote: »
    Nice one. Is it an Air to Water or Ground Source?

    It's a ground source. Waterkotte is the brand.


  • #553
    Wegian
    Registered Users Posts: 220 ✭✭Wegian


    335i wrote: »
    It's a ground source. Waterkotte is the brand.

    Thanks! Have you ever measured annual running costs?


  • #554
    ecowise
    Registered Users Posts: 125 ✭✭ecowise


    Wegian wrote: »
    Does anyone with a Heat Pump in for an extended period of time advise on

    - Annual Service Costs?
    - Annual Running Costs?
    - Any info on lifespan of components?

    We installed a ground source heat pump in our new build in late 2001 with underfloor heating. It is a fairly basic unit called a Genie that was made by a company in Cork that folded shortly afterwards. The quality of the installation was quite poor but the system has worked well enough in spite of that. The collector circulation pump failed in 2014 and had to be replaced. This failure was probably, at least in part, induced by air in the collector circuit due to brine leakage. I usually have to top up the circuit a number of times during the heating season due to fluid loss but this should not be necessary if properly plumbed.
    The running costs for heating our 250 m2 house is of the order of €200 per annum using night rate electricity and we supplement our heating with a wood stove (using our own wood) when needed. The house is well insulated (u value around 0.15), reasonably airtight and benefits from good solar gain.
    Our unit has a nominal rating of 12kW and we only run it at night. If I could redo the installation I would put in a 7kW unit and let it run during the heating season for the full 24 hours under thermostat control only. I would also put in extra underfloor insulation which is the one facet that is significantly under insulated (u value c. 0.3).


  • #555
    KCross
    Registered Users, Registered Users 2 Posts: 12,136 ✭✭✭✭KCross


    Wegian wrote: »
    Does anyone with a Heat Pump in for an extended period of time advise on

    - Annual Service Costs?
    - Annual Running Costs?
    - Any info on lifespan of components?

    - Ground source geothermal in since 2012, no service costs thus far.
    - €700-€800 per year which includes hot water for 350sqm house
    - Obviously I can't say for sure but it would be expected to last at least 20yrs with the main component to go being the compressor, which is not that expensive to replace, if it lasts 20yrs.


  • #556
    rolion
    Closed Accounts Posts: 3,362 ✭✭✭rolion


    Hi,

    Reading and doing my home work here...

    Can anyone tells the approximately price for an air to water heat pump, single phase, around 10Kw,outside mounting !?

    Can I use it only for heating radiators and UFH, average temperature of 20-25", without getting the boiler connected ? Also, without a storage cylinder.

    Home well insulated,I have solar panels and MHRV, looking to enjoy freedom off the grid/suppliers.

    Thanks in advance.


  • #557
    pieman123
    Registered Users Posts: 1 ✭pieman123


    Hi all,

    Been looking through the forum and was wondering has anyone been using a Thermia Heat Pump? I'm just starting specing for a new build and that is what was recommended to me by my engineer/BER. The house will be A3 rated at least will a large open living/dining/kitchen. The heat pump will be 11kw with UFH on the ground and first floor. Any advice much appreciated as my head is wrecked trying to find if they are any good!

    Pieman


  • #558
    ecowise
    Registered Users Posts: 125 ✭✭ecowise


    pieman123 wrote: »
    Hi all,

    Been looking through the forum and was wondering has anyone been using a Thermia Heat Pump? I'm just starting specing for a new build and that is what was recommended to me by my engineer/BER. The house will be A3 rated at least will a large open living/dining/kitchen. The heat pump will be 11kw with UFH on the ground and first floor. Any advice much appreciated as my head is wrecked trying to find if they are any good!

    Pieman

    I can't speak from experience of Thermia but I see there are numerous references to them on this site (if you have not already done so do a search in Google: thermia site:boards.ie and it will bring them up). While getting a good heat pump unit is important it should be remembered that it is only part of a system and the overall system design and installation are probably more important because there are any number if quality HP units that will do the job (so I would not get hung up on one brand) but the system design and installation are specific to your build.


  • #559
    ArraMusha
    Registered Users, Registered Users 2 Posts: 589 ✭✭✭ArraMusha


    Is there a comparison website for heatpumps or has anyone done a detailed comparison of the main models for sale in Ireland.
    One of the main specs I am interested in is the COP over a range of +7C to -7C. This does not seem to be readily shown in the datasheets but I have seen it published for one model.

    The models I would be interested in reviewing are in the 6-12kw range Daiken, Thermia, Panasonic, Mitsubishi, Heliotherm.


  • #560
    ArraMusha
    Registered Users, Registered Users 2 Posts: 589 ✭✭✭ArraMusha


    Is there a comparison website for heatpumps or has anyone done a detailed comparison of the main models for sale in Ireland.
    One of the main specs I am interested in is the COP over a range of +7C to -7C. This does not seem to be readily shown in the datasheets but I have seen it published for one model.

    The models I would be interested in reviewing are in the 6-12kw range Daiken, Thermia, Panasonic, Mitsubishi, Heliotherm.


  • #561
    ArraMusha
    Registered Users, Registered Users 2 Posts: 589 ✭✭✭ArraMusha


    Is there a comparison website for heatpumps or has anyone done a detailed comparison of the main models for sale in Ireland.
    One of the main specs I am interested in is the COP over a range of +7C to -7C. This does not seem to be readily shown in the datasheets but I have seen it published for one model.

    The models I would be interested in reviewing are in the 6-12kw range Daiken, Thermia, Panasonic, Mitsubishi, Heliotherm.


  • Advertisement
  • #562
    ecowise
    Registered Users Posts: 125 ✭✭ecowise


    ArraMusha wrote: »
    Is there a comparison website for heatpumps or has anyone done a detailed comparison of the main models for sale in Ireland.
    One of the main specs I am interested in is the COP over a range of +7C to -7C. This does not seem to be readily shown in the datasheets but I have seen it published for one model.

    The models I would be interested in reviewing are in the 6-12kw range Daiken, Thermia, Panasonic, Mitsubishi, Heliotherm.

    Have you looked at the SEAI HARP database or do you want more information than they provide?

    www. seai. ie/Your_Building/BER/BER_Assessors/Technical/HARP_Database/Heat_Pumps/
    (remove the spaces)


  • #563
    ArraMusha
    Registered Users, Registered Users 2 Posts: 589 ✭✭✭ArraMusha


    ecowise wrote: »
    Have you looked at the SEAI HARP database or do you want more information than they provide?

    www. seai. ie/Your_Building/BER/BER_Assessors/Technical/HARP_Database/Heat_Pumps/
    (remove the spaces)[/quote

    I'll have another look there again. Thanks


  • #564
    froshtyv
    Registered Users, Registered Users 2 Posts: 225 ✭✭froshtyv


    pieman123 wrote: »
    Hi all,

    Been looking through the forum and was wondering has anyone been using a Thermia Heat Pump? I'm just starting specing for a new build and that is what was recommended to me by my engineer/BER. The house will be A3 rated at least will a large open living/dining/kitchen. The heat pump will be 11kw with UFH on the ground and first floor. Any advice much appreciated as my head is wrecked trying to find if they are any good!

    Pieman

    Have a look here,

    http://www.boards.ie/vbulletin/showpost.php?p=95166507&postcount=507

    The Danfoss heat pump is the same heat pump as the Thermia


  • #565
    Wegian
    Registered Users Posts: 220 ✭✭Wegian


    Curious Geroge wrote: »
    Great info to know. I'm about to finalize on a Danfoss unit from heatpumpsireland but finding it impossible to get recommendations as they are suppliers and have fitters for each county. Based in galway, recommendations or general information welcomed (by PM or here). Thanks

    How did this work out? Just about to place an order for the Danfoss unit for a new build with the same supplier...


  • #566
    froshtyv
    Registered Users, Registered Users 2 Posts: 225 ✭✭froshtyv


    Wegian wrote: »
    How did this work out? Just about to place an order for the Danfoss unit for a new build with the same supplier...

    http://www.boards.ie/vbulletin/showpost.php?p=95166507&postcount=507


  • #567
    Wegian
    Registered Users Posts: 220 ✭✭Wegian


    Not good. This is what is specified in my BER and came recommended as the Premium Heat Pump, more homework required.


  • #568
    froshtyv
    Registered Users, Registered Users 2 Posts: 225 ✭✭froshtyv


    Wegian wrote: »
    Not good. This is what is specified in my BER and came recommended as the Premium Heat Pump, more homework required.

    The only reason they are proposed by a BER assessor is because there is an assumption that they can achieve a renewable contribution for hot water in Part L. This is incorrect but most BER assessors enter the wrong information in DEAP. A BER assessor should not be specifying a heat pump for a house. They dont know anything about heating, and pick a heat pump based on where it comes in on the harp database.
    The Danfoss & Thermia units still have a fixed speed compressor!! They take heat from the underfloor and cylinder to defrost the machine.


  • #569
    Curious Geroge
    Registered Users, Registered Users 2 Posts: 1,014 ✭✭✭Curious Geroge


    froshtyv wrote: »
    The Danfoss & Thermia units still have a fixed speed compressor!! They take heat from the underfloor and cylinder to defrost the machine.

    Are these good or bad points froshtyv ? How do the competitors defrost ?


  • #570
    Wegian
    Registered Users Posts: 220 ✭✭Wegian


    froshtyv wrote: »
    The only reason they are proposed by a BER assessor is because there is an assumption that they can achieve a renewable contribution for hot water in Part L. This is incorrect .

    In what way is this incorrect?
    The vendor assures me that no boost is required to heat DHW above 60 degrees.


  • Advertisement
  • #571
    froshtyv
    Registered Users, Registered Users 2 Posts: 225 ✭✭froshtyv


    Wegian wrote: »
    In what way is this incorrect?
    The vendor assures me that no boost is required to heat DHW above 60 degrees.

    That may be correct, but because the heat pump has a back-up heater you cannot use 0.7 as the EAF for hot water, you have to use the formula given in Appendix G in the DEAP manual.
    You will then find that the efficiency for hot water falls below 250% which means you get 0 for Part L renewable for hot water. So depending on your build, you could fall below 10 for the renewable side of Part L. This will mean you will have to re-think the renewable side of your build.

    Generally speaking a house with HRV proposed is near impossible to pass with a heat pump on its own.


  • #572
    Curious Geroge
    Registered Users, Registered Users 2 Posts: 1,014 ✭✭✭Curious Geroge


    Wegian wrote: »
    In what way is this incorrect?
    The vendor assures me that no boost is required to heat DHW above 60 degrees.

    Well, thats the furthest thing from the truth. Ask HPI to put it in writing !!

    Or have a read here http://heating.danfoss.com/pcmpdf/danfoss_total_user_vugfe202_en.pdf

    "To prevent the build up of bacteria in the water tank, the temperature of the water is increased at regular intervals using the integrated electrical heater (anti-legionella function). The factory-set time interval is seven days (can be adjusted). When the anti-legionella function is active, the heat pump produces hot water until the temperature for the start temperature sensor (5) has reached 60°C."

    Or sign your looking at the AQ

    http://www.heatpumpsireland.com/files/Danfoss_DHP-AQ_User%20Manual.pdf

    "the water in the water heater is given extra heat by the integrated immersion heater to prevent the build up of bacteria, an anti-legionella function"

    Now; start again and question every thing you were told to date and get it all in writing.


  • #573
    Wegian
    Registered Users Posts: 220 ✭✭Wegian


    froshtyv wrote: »

    Generally speaking a house with HRV proposed is near impossible to pass with a heat pump on its own.

    I hadnt bargained for this - I would have expected an expensive unit like a Heat Pump to achive part L compliance.
    My Provisional BER has the Danfoss and MHRV in the report and it meets Part L with an A2 rating.

    (Health Warning / Get-out Clause: There are inconsistencies in the way the report reads which I need to clarify with BER assessor)


  • #574
    sydthebeat
    Subscribers Posts: 41,850 ✭✭✭✭sydthebeat


    In my experience only heat pumps that are in excess of 500% spf have any hope of reaching part l compliance on their own. Most systems need at least one other bolt on technology such as pv cells


  • #575
    Wegian
    Registered Users Posts: 220 ✭✭Wegian


    sydthebeat wrote: »
    In my experience only heat pumps that are in excess of 500% spf have any hope of reaching part l compliance on their own. Most systems need at least one other bolt on technology such as pv cells

    Would a log burning stove do the trick?


  • #576
    Curious Geroge
    Registered Users, Registered Users 2 Posts: 1,014 ✭✭✭Curious Geroge


    Wegian wrote: »
    Would a log burning stove do the trick?

    Sorry Wegian but you need to go back to your BER accessor here. There is no way an A2W with a MHRV would pass Part L.

    What model MHRV are you going with ?

    For an A2 rating, what is the general spec of the house re cavity, insulation, roof, lined internally, makeup of the floor ?


  • Advertisement
  • #577
    Wegian
    Registered Users Posts: 220 ✭✭Wegian


    Curious Geroge wrote: »
    Sorry Wegian but you need to go back to your BER accessor here. There is no way an A2W with a MHRV would pass Part L.

    What model MHRV are you going with ?

    For an A2 rating, what is the general spec of the house re cavity, insulation, roof, lined internally, makeup of the floor ?

    Now that I have double checked the Axco MVHR C Range is included in the BER but not included in the Part L spec analysis so you are right, I need to revert to my BER Assessor.
    House Spec - 150mm in floor, 150mm bead in cavity and 400mm in the attic.

    Actually I need to double think selecting a Heat Pump at all now if it doesnt satisfy the Part L - is it worth the investment on its own merits?


  • #578
    FiOT
    Registered Users, Registered Users 2 Posts: 149 ✭✭FiOT


    Curious Geroge wrote: »
    Sorry Wegian but you need to go back to your BER accessor here. There is no way an A2W with a MHRV would pass Part L.

    What model MHRV are you going with ?

    For an A2 rating, what is the general spec of the house re cavity, insulation, roof, lined internally, makeup of the floor ?

    Hi All,

    Reading these new messages with interest (and slight panic)

    We plan to go with a thermia heat pump and wood burning stove to achieve Part L conformance. Our Part L document from our BER assessor says we have 10.17 kwh/m2/y renewable contribution which passes with the regulations. He has included MHRV in the document too so I assume he has taken this into account? How does the MHRV bring down your renewable contribution?

    Sorry, I don't fully understand all of this yet - still learning ahead of starting to build next March.


  • #579
    froshtyv
    Registered Users, Registered Users 2 Posts: 225 ✭✭froshtyv


    Wegian wrote: »
    I hadnt bargained for this - I would have expected an expensive unit like a Heat Pump to achive part L compliance.
    My Provisional BER has the Danfoss and MHRV in the report and it meets Part L with an A2 rating.

    (Health Warning / Get-out Clause: There are inconsistencies in the way the report reads which I need to clarify with BER assessor)

    If you look at the hot water efficiency adjustment factor in the report, and if 0.7 or 0.75 has been used then this is incorrect. It will be the BER assessor that will be pulled up on this if he is audited. Im not sure where that leaves you with regards the council if your house fails on Part L.


  • #580
    ecowise
    Registered Users Posts: 125 ✭✭ecowise


    FiOT wrote: »
    Hi All,

    Reading these new messages with interest (and slight panic)

    We plan to go with a thermia heat pump and wood burning stove to achieve Part L conformance. Our Part L document from our BER assessor says we have 10.17 kwh/m2/y renewable contribution which passes with the regulations. He has included MHRV in the document too so I assume he has taken this into account? How does the MHRV bring down your renewable contribution?

    Sorry, I don't fully understand all of this yet - still learning ahead of starting to build next March.

    Since you have not built yet why not build to PassivHaus standard and avoid the need for a central heating system? The MHRV alone would then be enough but you could include a woodstove for extra insurance and atmosphere.


  • #581
    BryanF
    Moderators, Home & Garden Moderators Posts: 10,143 Mod ✭✭✭✭BryanF


    ecowise wrote: »
    Since you have not built yet why not build to PassivHaus standard and avoid the need for a central heating system? The MHRV alone would then be enough but you could include a woodstove for extra insurance and atmosphere.
    Are you a passive house designer?
    I'm an Advocate for he passive standard, but there are no absolutes, and this post is misleading.
    A passive house will still require some heating, albeit much lower than an equivalent A rated house ( op, this is mainly to do with build quality/certified products, orientation/solar gain, attention to thermal bridging and air-tightness,)


  • Advertisement
  • #582
    ecowise
    Registered Users Posts: 125 ✭✭ecowise


    BryanF wrote: »
    Are you a passive house designer?
    I'm an Advocate for he passive standard, but there are no absolutes, and this post is misleading.
    A passive house will still require some heating, albeit much lower than an equivalent A rated house ( op, this is mainly to do with build quality/certified products, orientation/solar gain, attention to thermal bridging and air-tightness,)

    Apologies for not being clearer in my post, I assumed the architect/designer would spell things out in more detail. One advantage of the PassivHaus approach is that a dedicated & expensive central heating system is not necessary. This makes more capital available for the building's fabric especially glazing, insulation, airtightness and detailing to avoid thermal bridging. This is what I meant by saying a central heating system would not be needed but I agree that supplementary heating is necessary in most cases. This can be provided typically by a 1kW heating element in the MHRV but the actual size depends on the building's thermal load metrics. Although somewhat frowned upon by some purists the wood stove (or pellet if convenience is an issue) can also be used for this or in addition to it. The MHRV can move the heat around to other parts of the house from a point source like a wood stove if it is not centrally located to distribute heat by natural convection alone. A stove also adds a cosy factor that most people appreciate. In any event the PassivHaus approach has a lot to recommend it and should be the national standard for dwellings and office buildings in my opinion but that is another debate! Therefore I also believe that anyone building a house at this moment in time should aim to reach or exceed the PH standard and it need not have a significant cost implication.


  • #583
    THE DON FANUCCI
    Banned (with Prison Access) Posts: 144 ✭✭THE DON FANUCCI


    FiOT wrote: »
    Not a expert but here's my experience!

    We were in the same position as yourself in deciding, there really are so many options. We spoke with lots of different companies about lots of different options.

    We got our provisional BER done so we knew the heat demand of our new build first and this helped companies to accurately determine what type/spec heat pump we would need. We kind of felt in the end when we got all of our information that geothermal wasn't worth the extra money upfront. Due to the low heat demand of our build, we'd be a long time seeing the money back - if ever! One of the companies told us that the savings in heating bills with geothermal over air to water would only be about 70/80e a year. Obviously, that may not be right and motives may be questioned with that info but from my own research, they seem to be not far off the mark!

    I suppose a question I would have is how you know you need a 10kw heat pump before you've decided which one you're going for? The size of your heat pump surely varies from system to system, house to house. Again, I could be wrong!

    One thing about air to water heat pumps too that I found was that some models achieve the Part L compliance on their own whereas some require extra renewables too (PV or Solar) to meet the regs. The one we went with will achieve the regs on it's own so no need for anything else which is fab - one less moving part in the process!

    Talk to companies and see what they're offering and I can't stress enough how important it is to go with a reputable company, I have read horror stories on here.

    Best of luck!



    Hi Fiot can you PM me details of your heat pump type? are you happy with it? does it make loud noise? -thnaks for your help


  • #584
    MENACE2010
    Registered Users, Registered Users 2 Posts: 116 ✭✭MENACE2010


    Hi

    @ Don , Question does not really stack up.
    Air Source heatpumps do make noise , actually the noise could increase with the drop of outside temperature correct placement is key .
    We have a airsource heatpump and after the third winter I think i have the settings right. in other words the house is comfortable with a drop on cost on the electrical bills (also global warming was a great help ) .
    Our swedish pump fulfilled the part L. I did not consider solar ( water of PV at this point ) i have made arrangements for retro fit .. eg cable ducts etc if there is a change needed/


  • #585
    Wegian
    Registered Users Posts: 220 ✭✭Wegian


    Menace,

    Would you share Pump model and running costs pls?

    You can send by PM if you would prefer!!

    Thanks


  • #586
    THE DON FANUCCI
    Banned (with Prison Access) Posts: 144 ✭✭THE DON FANUCCI


    Is there big Tanks taking over the utility room with all air to water heat pumps?


  • #587
    ecowise
    Registered Users Posts: 125 ✭✭ecowise


    THE DON FANUCCI wrote: »
    Is there big Tanks taking over the utility room with all air to water heat pumps?

    From a Fraunhofer Institute report on heat pumps:

    "Air source heat pumps using reverse cycle defrosting are usually equipped with buffer storage. Furthermore, buffer storage ensures the minimum flow rate which the heat pump requires."

    buffer storage = tank/cylinder

    Interestingly they also conclude that generally direct heating systems (i.e. no buffer tank) are usually more efficient in absolute terms but I guess the operational benefits of a buffer tank outweigh a reduction in efficiency (SPF reduced from 2.9 to 2.7 approx. in their study under German climatic conditions).


  • #588
    Theimprover
    Registered Users Posts: 332 ✭✭Theimprover


    I got a quote for the following, its a 2700sqft house.

    Daikin 11kW Split System complete with Integrated 260ltr cylinder €8290 ex

    Brink Renovent 400 1 unit, Ducting Components
    Installation & Commissioning €4,970 ex

    Underfloor Heating 148 2m €3256 ex

    Can also get Panasonic Aquarea Air to Water Heat Pump Split System 12kw supply only for €4400

    Would this be a reasonable price? Would anyone have some links that they could send to me to buy online?


  • #589
    murphaph
    Registered Users, Registered Users 2 Posts: 19,031 ✭✭✭✭murphaph


    How did you size the heat pump you need?

    Heat pumps are funny, bigger is most definitely not better (google heat pump cycling)


  • #590
    Theimprover
    Registered Users Posts: 332 ✭✭Theimprover


    murphaph wrote: »
    How did you size the heat pump you need?

    Heat pumps are funny, bigger is most definitely not better (google heat pump cycling)


    A supplier quoted me after I gave them my plans.


  • #591
    murphaph
    Registered Users, Registered Users 2 Posts: 19,031 ✭✭✭✭murphaph


    I'm not being funny but you should be very careful here and ensure that your system is actually designed and laid out according to your needs and the physical properties of your new house. Even here in Germany where things are supposedly "done right", you have to double check what's being said to you (and especially what's being sold to you!)

    -Do you have any idea of the total heat demand for the property? (in the UK and here in Germany, an analysis according to EN 12831 is required for a new build like this to determine the heat demand for each individual room and for the building as a whole.

    You must understand, that without knowing the heat demand of each room, it's not possible to lay out the heating circuits correctly (the spacing, the length of pipe, the diameter of pipe etc.) and you will end up with rooms (especially the bathroom) where you can't get it up to desired temperature on the coldest days. Bathrooms are particularly problematic because they have the highest heat demand (you're typically wet and naked in them) and at the same time have less space in which to lay the pipe as shower trays and baths are usually not piped under (though you can and often should!).

    Once you've correctly calculated the heat demand for each room, you can calculate the overall demand and with it the heat pump you'll actually need to achieve that heat demand on the coldest days before the heat pump's immersion heater kicks in (something you'll want to avoid, but NOT at the cost of hugely over sizing the heat pump as you then have another problem: heat pump cycling, when the heat pump is so powerful it can very quickly satisfy the heat demand of a building and shuts off soon after coming on, then the process begins again and again and this costs a fortune in electricity as the most energy intensive part of running a heat pump is starting the motor up. Once it's running it is very efficient. Cycling also reduces overall life of the compressor. A heat pump's compressor will only do x thousand cycles before packing it in.

    Have your suppliers mentioned heat demand or the design or spacing of the heating circuits? If not, I'd want to know why not. have they mentioned the flow temperature of the system? You can compensate a badly installed system by jacking up the flow temp to a point where the heat pump is operating totally inefficiently. This often happens.

    If you don't invest the time now to understand how heat pumps work (not the deep technical details) in conjunction with a low temperature surface heating system like UFH then you will likely end up with a second rate system that costs far more to run than it should and can never be economically recitifed as once the pipes get buried in the screed, that's usually it.

    Have you a secondary heat supply planned at all? Log burner or something? That changes the dynamic if you are prepared to use such a heat source to support the heat pump on very cold days.

    First and foremost, make sure your insulation and airtightness is up to scratch. Money invested here is the best spent money of all.


  • Advertisement
  • #592
    Theimprover
    Registered Users Posts: 332 ✭✭Theimprover


    Thanks for the reply, we are trying to achieve a passive house. My architect has made contact with someone that we will be meeting next week who is going to fill is in on all the needs that we will need to do to achieve this.

    Very interesting read here http://passivehouseplus.ie/magazine/upgrade/ireland-s-first-fully-passive-retrofit.html


  • #593
    MOTM
    Registered Users, Registered Users 2 Posts: 412 ✭✭MOTM


    Methodology for heat pumps in DEAP now updated. http://www.seai.ie/Your_Building/BER/BER_FAQ/FAQ_DEAP/Energy_Requirements/How-do-I-assess-heat-pumps-in-DEAP-.html


  • #594
    RMDrive
    Registered Users, Registered Users 2 Posts: 554 ✭✭✭RMDrive


    We have a horizontal collector covering a large part of our site and it has worked really well over the last 8 years. Last year I planted some tress and shrubs over the area as I was sick and tired of cutting the grass. I've since been told that this isn't smart as over time the roots could damage the collection pipes.

    So ... are all tress and shrubs a no-no over the collection area? Which ones are ok? Are there other down-sides of planting, such as reduced efficiency or anything?

    Any advice appreciated.


  • #595
    murphaph
    Registered Users, Registered Users 2 Posts: 19,031 ✭✭✭✭murphaph


    Hmmm, a passive house of that size shouldn't require an 11kW heat pump or anywhere near it. We are building a 212m² house the moment here in Germany and we are not trying to, nor will we achieve a passive house standard and even for our build, the 11kW unit the house builder recommends is very questionable. The 9kW unit below would likely be fine AND the outside temps get much lower here than anywhere in Ireland.


  • #596
    Theimprover
    Registered Users Posts: 332 ✭✭Theimprover


    I will have a lot more info on what will be required in the next week or so, I'd imagine we wont really need much of a heating system if we are to achieve passive.


  • #597
    ecowise
    Registered Users Posts: 125 ✭✭ecowise


    RMDrive wrote: »
    We have a horizontal collector covering a large part of our site and it has worked really well over the last 8 years. Last year I planted some tress and shrubs over the area as I was sick and tired of cutting the grass. I've since been told that this isn't smart as over time the roots could damage the collection pipes.

    So ... are all tress and shrubs a no-no over the collection area? Which ones are ok? Are there other down-sides of planting, such as reduced efficiency or anything?

    I understand your frustration with grass cutting! However planting trees over the collector field is not recommended. Tree roots can penetrate deeper than horizontal collector depth (actual depth can vary a lot depending on tree type & growing conditions) but trees with strong tap root systems such as oak, sweet chestnut & walnut are particularly likely to go deep. This takes years, perhaps decades, and maybe you will have a different heating system by then! Another thought that occurs relates to efficiency. Tree root systems will tend to make the soil drier and thereby reduces its thermal conductivity and therefore collector efficiency. This could be especially problematic if you use your HP in summer even if only for hot water. There would also be a reduction in direct solar gain by the ground due to shading by the trees. Just some thoughts but you can still choose if you wish to leave the trees and not have to cut that grass!


  • #598
    RMDrive
    Registered Users, Registered Users 2 Posts: 554 ✭✭✭RMDrive


    ecowise wrote: »
    I understand your frustration with grass cutting! However planting trees over the collector field is not recommended. Tree roots can penetrate deeper than horizontal collector depth (actual depth can vary a lot depending on tree type & growing conditions) but trees with strong tap root systems such as oak, sweet chestnut & walnut are particularly likely to go deep. This takes years, perhaps decades, and maybe you will have a different heating system by then! Another thought that occurs relates to efficiency. Tree root systems will tend to make the soil drier and thereby reduces its thermal conductivity and therefore collector efficiency. This could be especially problematic if you use your HP in summer even if only for hot water. There would also be a reduction in direct solar gain by the ground due to shading by the trees. Just some thoughts but you can still choose if you wish to leave the trees and not have to cut that grass!


    Thanks a million for the reply. I think I'm resigned to getting to of the trees, however I'm wondering if the shrubs would be ok?

    Although your points about water content and solar gain should maybe make me think about taking up the whole lot :eek:


  • #599
    ecowise
    Registered Users Posts: 125 ✭✭ecowise


    Although less of a problem than trees personally I would not plant shrubs either but it is not a black and white situation. If you are getting significant benefit from the shrubs then it is understandable that you might choose to keep them. You might check the shrub varieties that you have in the unlikely event that they have particularly deep roots.


  • #600
    hellsbells83
    Registered Users Posts: 17 ✭hellsbells83


    Hi

    We're about to start a house build and we are deciding on heating system. We are interested in air to water heat pump with under floor heating. Just wondering if anyone has any experience with this system. I've read really mixed reviews some that it's really expensive to run and others that it's efficient. I think I've established that it is much more expensive with rads, not suited to that really.

    My main concern is that it has to be on all the time from October. I know the pump isn't running constant there would be thermostat that would mean pump would only be on when drops below certain temperature. We both work so won't be home during the day. So essentially the house will be heated even though no one is there.

    We were going to get the house a well insulated as possible, good Windows, heat recovery system and air tightness. So I'd hope we wouldn't need heat much, so in that case air to water heat pump seems like a massive investment where we could put oil system I Just to have for cold weather where required.

    Anyone any experience with air to water heat pump or any feedback


  • Advertisement
  • #601
    BarneyMc
    Registered Users, Registered Users 2 Posts: 1,504 ✭✭✭BarneyMc


    I have a query regarding A2W HPs and dual tariff meters here. Can someone please advise? Thank!


Advertisement