The Great Big Lawnmower Thread

my3cents · 18-04-2019 8:56am

celtic_oz wrote: »

this pro-lawn looks to be a rebadged hyundai (not just the engine ) seems good value €350 for the 53cm size

https://www.woodies.ie/pro-lawn-53cm-173cc-hyundai-self-propelled-petrol-lawnmower-1153280https://www.woodies.ie/pro-lawn-53cm-173cc-hyundai-self-propelled-petrol-lawnmower-1153280

Hyundai and all their lawn and outdoor stuff is rebadged chinese stuff.

Krombopulos Michael · 18-04-2019 9:09am

Just a little warning. I bought a cheap Hyundai push mower a few years ago, and two local lawnmower shops wouldn't service it as they advised wouldn't have the parts in stock to do so.

deezell · 18-04-2019 9:12am

my3cents wrote: »

Hyundai and all their lawn and outdoor stuff is rebadged chinese stuff.

As is a lot of big store stuff, but if it has a bring and Stratton engine, you have some comfort. I studied the pro lawn stuff closely in Woodies last week. It's decently made, a lot of the ancillary parts seen solid, and are common to a lot of generics and indeed the lower priced offerings of some more respectable brands. The key parts that determine it's life are engine, transmission if self propelled, and wheels. The first two will be the most costly to replace, wheels may wear or break if they are plastic or have no ball bearings, but then they will be cheap to replace in that case. A genuine Stiga ball bearing wheel can cost €50 each!,
The 51 and 53 cm cut pro lawns actually looks a good buy for such a big cut, but then you can buy stiga/castelgarden 53 series is Agrieuro for less than 400 if you take their cheaper engine options
Tip. If I recall, there are a couple of shop floor pro lawns in Woodies Naas with Honda engines being sold off as seen with a big discount, a bit pulled around but all there.

deezell · 18-04-2019 9:31am

Krombopulos Michael wrote: »

Just a little warning. I bought a cheap Hyundai push mower a few years ago, and two local lawnmower shops wouldn't service it as they advised wouldn't have the parts in stock to do so.

That seems petty, when all you want in a service is an oil change, clean deck, blade sharpen and balance, clean air filter and maybe drain carb bowl. Maybe pissed you didn't buy it from them. If somethings broken on it that's different, but Chadwicks among others are dealers for these, they would point you to an agent. I've never failed to get parts even for some old and obscure Lidl tools. Takes time though.

Krombopulos Michael · 18-04-2019 10:28am

deezell wrote: »

That seems petty, when all you want in a service is an oil change, clean deck, blade sharpen and balance, clean air filter and maybe drain carb bowl. Maybe pissed you didn't buy it from them. If somethings broken on it that's different, but Chadwicks among others are dealers for these, they would point you to an agent. I've never failed to get parts even for some old and obscure Lidl tools. Takes time though.

I was having carb issues with it and once it wasnt a B&S engine or type they supplied, they said they wouldnt have the parts.

tipping · 18-04-2019 11:34am

I found similar with the last mower I bought from one of the big stores.
It was a McCullough (can't remember the model), B&S engine but about €450 in the local Co-Op superstores.

The local service guys didn't want to look at it and said it was a pain to get parts etc. Couldn't get replacement blade etc. In addition it was just generally flimsy and cables, wheels etc all started giving trouble and I generally hated it.

Hence willing to spend a bit more now and be able to get it fixed locally if and when it does give trouble.

deezell · 18-04-2019 11:35am

Krombopulos Michael wrote: »

I was having carb issues with it and once it wasnt a B&S engine or type they supplied, they said they wouldnt have the parts.

I get that. You could spend a lot of time sourcing a carb kit for a spurious carburettor, only to find it doesn't solve the problem, maybe the carb is varnished, maybe compression is low, rings stuck, valves burnt or something else. A service guy knows its difficult to extract payment in that case, so won't take the risk. I've a Woodie's petrol power washer with Chinese engine. In a single year it burst two pressure hoses, replaced under warranty, the second time with a meshed steel covered proper hose. I got two years out of the engine, simply won't start now and compression is right down. I'll gut it it someday, but it's a piece of sh1t. Roc brand I think, sale special. Lesson learned.

Thekeencyclist · 18-04-2019 1:35pm

My choice would be to buy locally at a dealers where you know parts will be available and that the dealer can fix if anything ever happened, the big stores are ok for certain items but I wouldnt risk buying a lawnmower from them as they simply dont have the parts and is extra hassle to have to try and source them if a local mechanic cannot get them etc.

Have a Toro lawnmower here that I use for a small section of the garden which has shrubs etc and the ride on would be to awkward for + its an excuse to give the Toro a run to keep it running....the auld lad bought the Toro about 25 years ago, I pulled it out of the garage last week for the first time this year since last October and it started with the first pull, never once did it give any bother!!

kaiserrussel · 18-04-2019 4:05pm

Hi all

this a phenomenal thread with a huge volume of information. almost feel a thread specifically on makes/models vs price range is needed!

I posted a message a couple of weeks ago regarding a replacement belt for a Husq CTH 151, the reason being was I had gotten a non-Genuine husq belt online and my mechanic found it to be a little long when fitting. so I want to replace that.

I had gotten my mechanic to service the mower and wanted to sell it but I wasn't sure to trade in vs sell myself. My reason for selling is purely to get a newer model

So this brings me to my question - If I had a budget within 2K-2300K what would I be best to look out for. Assuming I sell my own privately or trade in ill have extra to add

Seems like folks I talk with are all advocating Stiga at the moment and the love for the Husq is fading

My Needs - entire site is just under an acre inclusive of house.

Husq - Is it true they are no longer selling rear discharge mowere?
Honda - Super mower but out of my budget new
Stiga - Are these castelgarden/mountfield rebadged and is there a model within my price range that someone would recommend?
Viking/Stihl – Is this just a rebrand and all components etc are the same?
Cub Cadet – Ive only heard of this brand
JD – I don’t think my budget is in this bracket

Outside of the above is there anything that you would suggest

I was recently in Boston visiting family and I was ill when I looked at the prices of some of the ride on mowers there ~1000 in the stores, I had thought of importing at one point but with the steps involved and the fact that these are only side discharge I felt Irish lawns would be too “damp”

Thanks for any thoughts provided

deezell · 19-04-2019 8:10am

Husq - plenty of rear baggers for sale, maybe dealers are dealing in rumours? Husky make cheaper built as well as higher quality mowers. Problem for consumer is knowing which grade you're getting, with the confusion of models.

Honda. Yes.

Stiga. Owned by GGP, parent of Castelgarden, Stiga, Alpins, Atco and Mountfield. Obviously huge commonality of parts, subtle differences in mowers and brand placement ( Stiga still has a professional range)

Stihl bought Viking. Mowers are identical, but in Oompah-Loompa colours.

Cub Cadet is an affordable American brand, only if you're buying in the US as you've seen. Owned by MTD, who also own Toro, high end push and zero turn mowers. Some nice MTD on agrieuro. MTD brand used in states for big store mowers but have quality also.

JD pricey, even their economy lines, made back in the past by Castelgarden among others

Snapper another well regarded brand, part of Briggs & Stratton behemoth, whose brands Simplicity, Murray and snapper are best known here.

This is a good read though US focused so incomplete.
https://todaysmower.com/riding-mower-brands/
If you get a trade in offer off list pricr anywhere north of €900 for the cth151 I'd take it. You'll struggle to get 800 on Adverts/Donedeal unless it's only a few years old ( how old? It's been out for eons). Do the usual. Seek a cash price, then work out real trade in value. Posters here getting €300+ off for cash. Good hunting

DeborahLQ · 21-04-2019 1:27pm

Great thread, but a bit overwhelming. Anybody know anything about these ones? I'm thinking of getting one.

Recycler 22 in. SmartStow High Wheel Variable Speed Walk Behind Gas Self Propelled Mower
https://www.homedepot.com/p/Toro-Recycler-22-in-SmartStow-High-Wheel-Variable-Speed-Walk-Behind-Gas-Self-Propelled-Mower-20339/205026227

my3cents · 21-04-2019 1:45pm

DeborahLQ wrote: »

Great thread, but a bit overwhelming. Anybody know anything about these ones? I'm thinking of getting one.

Recycler 22 in. SmartStow High Wheel Variable Speed Walk Behind Gas Self Propelled Mower
https://www.homedepot.com/p/Toro-Recycler-22-in-SmartStow-High-Wheel-Variable-Speed-Walk-Behind-Gas-Self-Propelled-Mower-20339/205026227

Looks fine to me but it depends how much you have to pay for it. I suspect it will be a lot more here than the $320 in the US.

Thats probably front wheel drive btw which is a handy feature as you can control traction or stop and turn by pushing your weight onto the handlebars.

deezell · 21-04-2019 8:59pm

I doubt if anyone is importing that particular model, 20339, it's possibly an all wheel drive. Expect to pay €800 - €900 here for similar.
http://www.gerrycroffey.ie/lawnmowers-2.html

MascotDec85 · 21-04-2019 9:27pm

Anyone have a robot mower? Seriously considering getting one. Looking for one that would do about half an acre/2000 sq m

deezell · 21-04-2019 10:33pm

MascotDec85 wrote: »

Anyone have a robot mower? Seriously considering getting one. Looking for one that would do about half an acre/2000 sq m

I have, she makes a decent curry as well. Very expensive to run though.
Seriously though, have a look here,
https://dermotcasey.com/c/lawn-garden/robotic-lawnmowers
Expect to pay very roughly €150 to €250 per 100sqM of area to be mown, if you want a machine that can do the job.
Check out this 20 grand machine for football pitches/ sports parks etc.!
https://dermotcasey.com/product/wiper-yard-301-robotic-mower-30000-sm

Krombopulos Michael · 24-04-2019 8:24am

Krombopulos Michael wrote: »

So, bought myself a STIHL RT 5112Z. Decided after lots of research (mostly the legend that is deezell) that I needed a twin cylinder mower for mowing on slopes that can bag and mulch.

Got 300euro off with my local dealer including oil and safety gear thrown in to the deal, so im happy out. Thanks to all on the thread for the info, looking forward to taking delivery now.

So just an update on the new STIHL RT 5112Z.

Glad I went for a twin cylinder model as the slope on my lawn was a little steeper than I thought in places, and I can hear a little strain on the motor going up while cutting (Not steep enough to tip over)

Very easy to drive and operate and seat is comfy, and the controls layout are good.

My only negatives are

1) The box sliding handle to tip out the grass came out in my hand away from the box. It uses a plastic retaining clip to keep in place and it popped off and was lost in a sea of grass clippings, however a simple bolt and nut has that sorted out immediately.

2) At your left foot there is a button to press to keep the blades engaged when going in reverse. I found this a bit hit and miss and it seems like every time you cut in reverse you must press it, not just hold it down all the time.

Apart from this, the engine is strong and it was great to use. After the first cut, I have inserted the mulch plug and been out for the second cut a few days later which was a breeze.

Thanks again for all the advice from this thread.

FannyBadger · 24-04-2019 9:42am

Does anyone in here have some hints and tips on the maintenance/servicing of a ride-on mower?

I bought a Castelgarden XDC170hd last year, for cutting about an acre of grass. It didn't get a massive amount of use due to a new baby and most of the grass being burnt by the sun!
So far, I haven't done anything much in the line of servicing, meaning it still has the same oil which came when it was delivered. I have also noticed a few rust spots developing on the underside of the deck.

From reading a few other posts, I think I will heed Deezell's advice about painting the underside with a couple of coats of red oxide paint to stop the rust anyway.
Does anyone know if it is tricky to get the deck off a Castelgarden, or should I just get something like a mower jack to prop the deck up so I can get at it without having to drop it off? I had a go at taking it off, but it wasn't co-operating so I left it in case I did more damage than good.

Is it OK to powerwash the deck to get the stubborn grass off, or could this damage the blades/deck?

Should you use the hose connectors to wash the deck after each use? Does this really work, or does this just contribute to the rusting?

Should I change the oil, or would it be OK for one more season?

Is it advisable to get the mower serviced once a year by a dealer/manufacturer, or can you do most of it yourself and bring to a service centre every 2/3 years instead?

Any other hints/tips would be greatly appreciated! I'm hoping to keep this mower going for 10 years at least!

ArrBee · 24-04-2019 9:52am

I'm no expert and part of the reason for this is post is to follow the thread

One tip I have found is using an air compressor for cleaning if you have one. Especially the fabric of the grass collector.

Daz_ · 24-04-2019 10:11am

FannyBadger wrote: »

Does anyone in here have some hints and tips on the maintenance/servicing of a ride-on mower?

I bought a Castelgarden XDC170hd last year, for cutting about an acre of grass. It didn't get a massive amount of use due to a new baby and most of the grass being burnt by the sun!
So far, I haven't done anything much in the line of servicing, meaning it still has the same oil which came when it was delivered. I have also noticed a few rust spots developing on the underside of the deck.

From reading a few other posts, I think I will heed Deezell's advice about painting the underside with a couple of coats of red oxide paint to stop the rust anyway.
Does anyone know if it is tricky to get the deck off a Castelgarden, or should I just get something like a mower jack to prop the deck up so I can get at it without having to drop it off? I had a go at taking it off, but it wasn't co-operating so I left it in case I did more damage than good.

Is it OK to powerwash the deck to get the stubborn grass off, or could this damage the blades/deck?

Should you use the hose connectors to wash the deck after each use? Does this really work, or does this just contribute to the rusting?

Should I change the oil, or would it be OK for one more season?

Is it advisable to get the mower serviced once a year by a dealer/manufacturer, or can you do most of it yourself and bring to a service centre every 2/3 years instead?

Any other hints/tips would be greatly appreciated! I'm hoping to keep this mower going for 10 years at least!

Great questions and look forward to the replies as is a similar position with mine

deezell · 24-04-2019 10:38am

Krombopulos Michael wrote: »

So just an update on the new STIHL RT 5112Z.
....At your left foot there is a button to press to keep the blades engaged when going in reverse. I found this a bit hit and miss and it seems like every time you cut in reverse you must press it, not just hold it down all the time.....

You don't hold it down. When you stop, press it once, release, you have 5 second to select reverse without blade disengagement, or, you can stop, select revese and within a second press and release the button to enable reverse mowing . It works on stop by stop basis, there's no programming mechanism to disable it afaik, though here is a procedure on ignition to disable automatic full bag disengagement, by pressing for five seconds, the reverse mowing button and drive pedal, while the engine is off and ignition is on (page 35). On the bigger 6127ZL there is an indicator on the display that shows when the reverse mowing button mode is selected, and you have the 5s window to engage reverse.

Krombopulos Michael · 24-04-2019 10:46am

deezell wrote: »

You don't hold it down. When you stop, press it once, release, you have 5 second to select reverse without blade disengagement, or, you can stop, select revese and within a second press and release the button to enable reverse mowing . It works on stop by stop basis, there's no programming mechanism to disable it afaik, though here is a procedure on ignition to disable automatic full bag disengagement, by pressing for five seconds, the reverse mowing button and drive pedal, while the engine is off and ignition is on (page 35). On the bigger 6127ZL there is an indicator on the display that shows when the reverse mowing button mode is selected, and you have the 5s window to engage reverse.

Good to know. Need to read the manual

Krombopulos Michael · 24-04-2019 11:40am

Are ride on lawnmower lifters any use to allow easy access underneath for maintenance?

https://www.amazon.co.uk/lifter-Lifting-Device-Garden-Tractor/dp/B00OV5JKLK

deezell · 24-04-2019 12:40pm

FannyBadger wrote: »

.....From reading a few other posts, I think I will heed Deezell's advice about painting the underside with a couple of coats of red oxide paint to stop the rust anyway.

Do.

Does anyone know if it is tricky to get the deck off a Castelgarden,

It is tricky, older CGs required removal of the Engine belt pulleys to free the belts. Not sure of the very new models, but yours is an electric clutch non-synchronous blade, should be easy to drop the belt from the clutch. I know it was common on the older mowers to remove the grass box and just stand the mower upright, mad as it seems, on a hard surface it would sit nicely on its rear steel bag hooks, a few bits bit of wood maybe. Took two to lift the front with the back wheels locked/wedged, or lift with a pulley in a garage. Ideal for blade inspection, painting, cleaning. once the fuel was low, oil went to back of the engine, battery sealed type so no leaks. Also for rear drive sprocket, differential, chain work on a manual gearbox drive it was very handy. I found it easier eventually to just drop the deck once you got the hang of it.

Is it OK to powerwash the deck to get the stubborn grass off, or could this damage the blades/deck?

You should be OK, don't point the jet directly at the shaft bearing.

Should you use the hose connectors to wash the deck after each use? Does this really work, or does this just contribute to the rusting?

Jurys out on this. I think it's pointless and messy, unless the grass was mush to begin with.

Should I change the oil, or would it be OK for one more season?

You'll be Ok for this season, but change oil at least next season, it can get moisture in it lying up, but Id say there are mowers out there with the same oil for years. With low use filter should be good for 2 seasons, but cheap as chips to DIY change.

Is it advisable to get the mower serviced once a year by a dealer/manufacturer, or can you do most of it yourself and bring to a service centre every 2/3 years instead?

2/3 Sounds like a plan. Dealer might spot something amiss. He'll advise changing belts even if they look serviceable to you, otherwise you might break one in the first few weeks and moan, "this was just serviced"

Any other hints/tips would be greatly appreciated! I'm hoping to keep this mower going for 10 years at least!

You might find this parts manual useful. Part names French, but pictures and part numbers are the same. Get a pdf translate app something if you like.
https://www.ggpfrance.net/index.php/documents/catalogue-pieces-de-rechanges/2018/castelgarden-autoportees-2018/7441-2t2620273-c16-xdc170hd-2018/file

deezell · 24-04-2019 12:48pm

Krombopulos Michael wrote: »

Are ride on lawnmower lifters any use to allow easy access underneath for maintenance?

https://www.amazon.co.uk/lifter-Lifting-Device-Garden-Tractor/dp/B00OV5JKLK

Won't break the bank, might stop you breaking your arm! Irish version of this is a cut down fence post.

Doctors room ghost · 24-04-2019 1:15pm

FannyBadger wrote: »

Does anyone in here have some hints and tips on the maintenance/servicing of a ride-on mower?

I bought a Castelgarden XDC170hd last year, for cutting about an acre of grass. It didn't get a massive amount of use due to a new baby and most of the grass being burnt by the sun!
So far, I haven't done anything much in the line of servicing, meaning it still has the same oil which came when it was delivered. I have also noticed a few rust spots developing on the underside of the deck.

From reading a few other posts, I think I will heed Deezell's advice about painting the underside with a couple of coats of red oxide paint to stop the rust anyway.
Does anyone know if it is tricky to get the deck off a Castelgarden, or should I just get something like a mower jack to prop the deck up so I can get at it without having to drop it off? I had a go at taking it off, but it wasn't co-operating so I left it in case I did more damage than good.

Is it OK to powerwash the deck to get the stubborn grass off, or could this damage the blades/deck?

Should you use the hose connectors to wash the deck after each use? Does this really work, or does this just contribute to the rusting?

Should I change the oil, or would it be OK for one more season?

Is it advisable to get the mower serviced once a year by a dealer/manufacturer, or can you do most of it yourself and bring to a service centre every 2/3 years instead?

Any other hints/tips would be greatly appreciated! I'm hoping to keep this mower going for 10 years at least!

It’s easy take the deck off its 2 bolts and 2 r clips just take a few pictures before you dismantle and mark the threads incase they turn with the deck off because they are used to level the deck.
Then guide the blade belt off the pulley and pull out the deck with belt attached.
Youd have the deck off in 10 minutes.
Turn it upside down outside and power wash it thoroughly both sides and leave it inside to dry for a few days.
A light sand then and paint it.theres plastic covers on the top you can remove them too if you want.
Hammerite is the stuff you want to paint on it.i do paint mine both sides hammerite under and a red steel girder paint outside.
Leave it a week somewhere warm then to cure and refit.
I do this every year end of cutting and sharpen the blades with the grinder and service the engine.oil change oil filter and the little petrol filter on the fuel line.air filter too if it needs one or bang it out and a shot of the airline.

FannyBadger · 24-04-2019 4:56pm

Thanks very much Deezell, Doc and Arbee for all the replies and advice on this!

Deezell, that parts list may come in very handy down the line so cheers for that.

@ Michael - I have one of those lawnmower lifting jacks on order, I can let you know if it's any use whenever it arrives (Should have been here last week).
You might need to be wary of tipping it to the correct side to make sure oil doesn't leak...

Krombopulos Michael · 25-04-2019 8:09am

FannyBadger wrote: »

@ Michael - I have one of those lawnmower lifting jacks on order, I can let you know if it's any use whenever it arrives (Should have been here last week).
You might need to be wary of tipping it to the correct side to make sure oil doesn't leak...

Where did you get yours from (when it arrives)

Cormo87 · 25-04-2019 8:10am

Hi All,

Is there anywhere in Dublin that takes old petrol lawnmowers in when buying a new one?

Thanks.

deezell · 25-04-2019 9:26am

Cormo87 wrote: »

Hi All,

Is there anywhere in Dublin that takes old petrol lawnmowers in when buying a new one?

Thanks.

Mower city in Emmet rd Inchicore for one. If they sell used, then they most likely take trade in. If you're just looking to get rid of a knackered mower, they'll probaly take it anyway. If it's in any way working, you'll sell on Adverts or Donedeal.

FannyBadger · 25-04-2019 10:52am

Krombopulos Michael wrote: »

Where did you get yours from (when it arrives)

I got it on ebay but can't paste the URL here as I'm too new!

Similar price to the Amazon one, but free delivery from Germany I think.
The delay is not with Germany though - it got to Ireland last week, but DPD sent it to Wexford. I thought this was the point of Eircodes...

fryup · 25-04-2019 10:52am

can i make a homemade mulching kit for my ride on...i just basically need to block the collection chute?

NIMAN · 25-04-2019 11:37am

fryup wrote: »

can i make a homemade mulching kit for my ride on...i just basically need to block the collection chute?

Not sure if this would be possible.

I also think that mowers made for mulching actually have a different blade to a normal mower, specifically for the purpose.

I could be wrong though;)

Doctors room ghost · 25-04-2019 1:02pm

fryup wrote: »

can i make a homemade mulching kit for my ride on...i just basically need to block the collection chute?

No you need to change the blades from the normal cutting ones to mulching ones for it to work properly.you can buy mulching kits which include blades and the plug

deezell · 25-04-2019 1:23pm

NIMAN wrote: »

Not sure if this would be possible.

I also think that mowers made for mulching actually have a different blade to a normal mower, specifically for the purpose.

I could be wrong though;)

Mulch specific mowers have the mulch blades. 3 in 1 mowers might have a compromise blade, perhaps a serrated impeller fin. Most ride on mulch plugs will have some kind of curve or baffle to hopefully direct the grass back over the centre of the blades, so they recycle it a few times before falling through, and also to distribute it evenly over the cut width. A straight blockage, as we all know, will often result in a trail of clumps in the centre, not surprising, as the blockage is often causesd by long damp soft grass. This is equally unsuitable for mulching anyway. Fwiw, I've noticed that my ride on performs as a decent mulcher following a chute blockage in a heavy patch, but only when when mowing through the lighter areas of growth. It clumps when I hit the heavy bit on the next lap, at which point I see the previous lap's clumps, and have to poke out blockage.

ustari · 29-04-2019 1:47pm

On that note, my Iseki SXG15 gets blocked quite a bit. Mostly down to me not tipping the box in time I am guessing.

The reason behind that is I don't get any notification when I need to tip it. This is an old second hand one so not sure, but did these have an alarm/notification bell on release?
Needs a service soon so might have a look at getting that back working also if it did.

Thanks

deezell · 29-04-2019 2:04pm

ustari wrote: »

On that note, my Iseki SXG15 gets blocked quite a bit. Mostly down to me not tipping the box in time I am guessing.

The reason behind that is I don't get any notification when I need to tip it. This is an old second hand one so not sure, but did these have an alarm/notification bell on release?
Needs a service soon so might have a look at getting that back working also if it did.

Thanks

The Vikings have a bag full alarm, and it can be set to cut off the mowing blades when it goes off. It's adjustable, it's a small lever that protrudes into the grass catcher. if the Iseki has an alarm, there should be a small lever sensor of some type to detect the building pile of grass.

deezell · 29-04-2019 2:40pm

ustari wrote: »

On that note, my Iseki SXG15 gets blocked quite a bit. Mostly down to me not tipping the box in time I am guessing.

The reason behind that is I don't get any notification when I need to tip it. This is an old second hand one so not sure, but did these have an alarm/notification bell on release?
Needs a service soon so might have a look at getting that back working also if it did.

Thanks

Parts diagrams here. Your bag type in the first few files, sensor plate and switch arrangement on the base of the bag to measure the weight of grass by the look of it.

http://iseki.ie/manuals/Manuals.html#C:/Users/ANDREW/Desktop/ISEKI%20UK%20Parts%20Manuals/SXG15

amadangomor · 02-05-2019 1:04pm

Anyone have any knowledge of the Aldi electric lawnmower on sale this week?

https://www.aldi.ie/ferrex-40v-cordless-lawn-mower-skin/p/097702269775900

deezell · 02-05-2019 1:53pm

amadangomor wrote: »

Anyone have any knowledge of the Aldi electric lawnmower on sale this week?

https://www.aldi.ie/ferrex-40v-cordless-lawn-mower-skin/p/097702269775900

Batteries not included

Battery is €35, and charger maybe €20. You might need a second battery, 40V 2.5 A hour battery will deliver maybe 500W for maybe 10 minutes or less, so toud want a very small lawn and cut often to reduce the load. It's only rated to last 30 min just spinning with no load.

amadangomor · 02-05-2019 2:05pm

deezell wrote: »

Batteries not included

Battery is €35, and charger maybe €20. You might need a second battery, 40V 2.5 A hour battery will deliver maybe 500W for maybe 10 minutes or less, so toud want a very small lawn and cut often to reduce the load. It's only rated to last 30 min just spinning with no load.

Thanks, noticed the extra for battery and charger but was thinking of getting at least one other compatible tool so would be ok with that.

Probably would need 20 mins to do front and back so good info from you there

First cut is usually later than i'd like as lawn is usually waterlogged in winter so can be very long

Might go for the B and Q corded or just go petrol again.

glic83 · 02-05-2019 9:57pm

Hey guys just looking on advice between these 2 petrol lawnmowers in woodies.
https://www.woodies.ie/pro-lawn-42cm-139cc-hyundai-push-petrol-lawnmower-1153278?utm_source=google_shopping&&gclid=CjwKCAjwqqrmBRAAEiwAdpDXtBMfr8uOo0zRJxz2hh0G__Z-pLCagqKTBP3y7ny_ViaWLUs5J3kvLBoCmcsQAvD_BwE

And
https://www.woodies.ie/pro-lawn-41cm-125cc-petrol-lawnmower-online-only-offer-1106894
Both are the same price, would I be right in saying the 2nd mower with the Briggs & Stratton engine would be better then the Hyundai engine? I don't have a very big back & front but not a fan of electrical lawnmowers and back tends to hold a lot of water at times so have found the petrol mowers better.

glic83 · 02-05-2019 9:57pm

Hey guys just looking on advice between these 2 petrol lawnmowers in woodies.
https://www.woodies.ie/pro-lawn-42cm-139cc-hyundai-push-petrol-lawnmower-1153278?utm_source=google_shopping&&gclid=CjwKCAjwqqrmBRAAEiwAdpDXtBMfr8uOo0zRJxz2hh0G__Z-pLCagqKTBP3y7ny_ViaWLUs5J3kvLBoCmcsQAvD_BwE

And
https://www.woodies.ie/pro-lawn-41cm-125cc-petrol-lawnmower-online-only-offer-1106894
Both are the same price, would I be right in saying the 2nd mower with the Briggs & Stratton engine would be better than the Hyundai engine? I don't have a very big back/front garden but not a fan of electrical lawnmowers and back tends to hold a lot of water at times so have found the petrol mowers better.

my3cents · 02-05-2019 10:12pm

glic83 wrote: »

Hey guys just looking on advice between these 2 petrol lawnmowers in woodies.
https://www.woodies.ie/pro-lawn-42cm-139cc-hyundai-push-petrol-lawnmower-1153278?utm_source=google_shopping&&gclid=CjwKCAjwqqrmBRAAEiwAdpDXtBMfr8uOo0zRJxz2hh0G__Z-pLCagqKTBP3y7ny_ViaWLUs5J3kvLBoCmcsQAvD_BwE

And
https://www.woodies.ie/pro-lawn-41cm-125cc-petrol-lawnmower-online-only-offer-1106894
Both are the same price, would I be right in saying the 2nd mower with the Briggs & Stratton engine would be better than the Hyundai engine? I don't have a very big back/front garden but not a fan of electrical lawnmowers and back tends to hold a lot of water at times so have found the petrol mowers better.

If all you need is a push mower then its a decent machine which if looked after will do a good bit of work. The Briggs engine version is probably the better I suspect the hyundai is just a rebadged cheap chinese engine.

Both prices are a rip off though. Its essentially the same machine as Lidl had here for the same money a month ago. I say its a rip off because Lidl were selling the same machine in the UK for £139 (about €165). I know because I still have one in the back of my car in I bought last Friday in the UK. I've still a previous version that has suffered 4 seasons of very rough use (it even cut an acre a good few times when the ride on was out of action) but decided to get a spare at a decent price while I could.

Edit> Comparing engines it would be hard to choose between then the hyundai one might be slightly more powerful?

glic83 · 02-05-2019 10:26pm

my3cents wrote: »

If all you need is a push mower then its a decent machine which if looked after will do a good bit of work. The Briggs engine version is probably the better I suspect the hyundai is just a rebadged cheap chinese engine.

Both prices are a rip off though. Its essentially the same machine as Lidl had here for the same money a month ago. I say its a rip off because Lidl were selling the same machine in the UK for £139 (about €165). I know because I still have one in the back of my car in I bought last Friday in the UK. I've still a previous version that has suffered 4 seasons of very rough use (it even cut an acre a good few times when the ride on was out of action) but decided to get a spare at a decent price while I could.

Edit> Comparing engines it would be hard to choose between then the hyundai one might be slightly more powerful?

Yeah I was just going by the fact that it was a known brand name, haven't come across anyone with the Hyundai mower. How much was the lidl one here a few weeks ago? 200? The 2 mentioned above seem to be the best value for what I'd need , haven't seen any others.

deezell · 02-05-2019 10:45pm

glic83 wrote: »

Yeah I was just going by the fact that it was a known brand name, haven't come across anyone with the Hyundai mower. How much was the lidl one here a few weeks ago? 200? The 2 mentioned above seem to be the best value for what I'd need , haven't seen any others.

Buy this recognised brand Stiga online for €170 delivered, GGP own brand engine,
https://www.agrieuro.co.uk/stiga-collector-43-push-lawn-mower-100-cc-engine-petrol-lawn-mower-p-10246.html
Or
Sign up for Woodies Newsletter, get 10% of their mower when bought online.
https://www.woodies.ie/sign-up-to-our-newsletter-homepage-header

glic83 · 02-05-2019 10:51pm

deezell wrote: »

Buy this recognised brand Stiga online for €170 delivered, GGP own brand engine,
https://www.agrieuro.co.uk/stiga-collector-43-push-lawn-mower-100-cc-engine-petrol-lawn-mower-p-10246.html
Or
Sign up for Woodies Newsletter, get 10% of their mower when bought online.
https://www.woodies.ie/sign-up-to-our-newsletter-homepage-header

*This discount code cannot be use in conjunction with any other discount or special offer. Cannot be used on Lawnmowers, Garden Powertools, Sheds, Showers, Pressure Washers, Dewalt or woodiespartyzone.ie

deezell · 02-05-2019 10:56pm

glic83 wrote: »

*This discount code cannot be use in conjunction with any other discount or special offer. Cannot be used on Lawnmowers, Garden Powertools, Sheds, Showers, Pressure Washers, Dewalt or woodiespartyzone.ie

Bummer. Well Chadwicks have the actual Hyundai mowers in fetching blue livery starting at €179 for the 42cm push. Here's their spring brochure

http://www.chadwicks.ie/images/downloads/Spring_Sale_-_Chadwicks.pdf

my3cents · 02-05-2019 11:06pm

deezell wrote: »

Buy this recognised brand Stiga online for €170 delivered, GGP own brand engine,
https://www.agrieuro.co.uk/stiga-collector-43-push-lawn-mower-100-cc-engine-petrol-lawn-mower-p-10246.html
Or
Sign up for Woodies Newsletter, get 10% of their mower when bought online.
https://www.woodies.ie/sign-up-to-our-newsletter-homepage-header

Thats more like the right price for a very similar (possibly better) machine.

glic83 · 03-05-2019 4:03pm

my3cents wrote: »

Thats more like the right price for a very similar (possibly better) machine.

@my3cents you're referring to the first one I take it? Even though it has the smaller engine?

my3cents · 03-05-2019 4:28pm

glic83 wrote: »

@my3cents you're referring to the first one I take it? Even though it has the smaller engine?

Yep. When you include delivery and a fivers worth of engine oil its a good deal.

Smaller engine may actually be more powerful. Very hard to directly compare them as they all quote different figures.

The Great Big Lawnmower Thread

Comments