Home heating automation

reignschaos wrote: »

@Caillte For a tenner I was thinking of doing the upgrade too. Have until the end of the month. As @Deezell said, let us know what you think.

I've been using the new app for 2 months now. The overview screen is a big improvement on the old app i find. I'm liking the new app a lot more than i expected. I don't realy find anything i miss from the old app.

FYI,

Tado wall thermostat currently 50% off at amazon.

Also for those of you using camel camel camel they are no longer tracking price changes on request of amazon. I didnt get any email only spotted it when i logged on their website to see where the thermostat was currently priced.

GarIT wrote: »

I wonder why they would do that

Sez they;


In response to the COVID-19 crisis, Amazon has asked us to stop updating products in Europe until further notice. Stay safe out there.

In response ro the Covid-19 crisis, i have decided to wear odd socks. Makes as much sense.

Anyone switched from EPH/Ember to another system. We have two heating zones and hot water - is it just a matter of a new controller, thermostat etc or is it a bigger job (can they re-use the valves/switches for the existing zones or would they need to be changed).

paddyb wrote: »

Anyone switched from EPH/Ember to another system. We have two heating zones and hot water - is it just a matter of a new controller, thermostat etc or is it a bigger job (can they re-use the valves/switches for the existing zones or would they need to be changed).

I swapped out EPH my sytem to tado. But the EPH controller was left as is and switched to always on. Works a treat.

Thanks had a look at the Drayton site and it looks like their controller will slot on to the wiring back panel of the eph so no wiring will be needed

paulgrogan.eu wrote: »

Hi Deezell,


Sorry to dig up an old post. One thing I forgot to ask on this was what types of mechanical stats you would recommend for a HW tank? I don't have anything on my tank at the moment to regulate the temp, other than a big tap to open or close the amount of hot water fed into it and we've guessed the temp of the water by running the hot tap and measuring. I also agree that we probably don't need regular smart access to this information, just set it and leave it, and adjust it if going away or whatever. Do you have a particular one that you would recommend, as we are aiming to get our Tado and new valves installed in the coming months so we can have control over our heating, as over this winter it was all over the place!


Cheers


Paul.

Cylimder stat like this. You strap it to tank, if the tank is a foam insulated one you cut a stat shaped hole in it.
This is the only place I've found still delivering online sales. Woodie's, Screwfix were overwhelmed with onl8ne orders.
https://www.mcmahons.ie/cylinder-pipe-thermostat

Thanks for checking that - their video made it look so simple! Still not a big job I guess but I would get someone to do this for me rather than messing around with the wiring

https://wiser.draytoncontrols.co.uk/node/24

paulgrogan.eu wrote: »

Awesome, thank you for that.


One other question. Am I missing something, or will Tado not keep firing the boiler every time the tank drops even 1 deg below the set temp on that Thermostat? Say I set it to 60 deg, if the tank drops to 59 deg, will it fire the boiler to bring it back up again?


Cheers

No, these are mechanical stats. Firstly, Tado will have nothing to do with their boiler call via their zone valve relay, UNLESS you get the Tado ext. kit and use it for HW timing. Regardless, the mechanical nature of the cylinder stat has a fair amount of hysteresis, that is, it will need to heat the water a good few degrees past the setting to cut out, then cool a good few degrees below to cut in again, say, set for 60°, it will heat till 63° ( timer permitting), cut the boiler, and will have to cool to 57° to turn on again.

paulgrogan.eu wrote: »

Hi Deezell,


Yep so I do indeed have the Ext. Kit as I want Tado to handle the HW tank and stop ourselves using the immersion in the summer. At the moment we only have valves to control ground floor & 1st floor, with an open pipe all the way to the HW tank from the boiler. So we're planning to install a 3rd valve on the HW tank pipe so that can also be switched on/off by Tado.


We'll also use the Ext.Kit for our wireless stat on the ground floor, but we'll hardwire the landing one as we have an easy route down via the pipes to the Tado controller beside the boiler for that one.


Regards,


P.

Perfect plan. Cylinder Thermostat will keep cylinder topped up during the summer or winter, timer really only useful to knock the HW off during holidays, weekends away (☹), or if you have a badly insulated cylinder and only want HW in short timed spurts, 70's style.

Also from a search
How to manually restart if your Nest thermostat is frozen or stuck

Press your thermostat ring and hold it down until the screen turns off (about 10 seconds). Then let go of the ring.
Press and release the ring to turn it back on and complete the restart process. You'll see the Nest logo when it begins to start up.

Mickeroo wrote: »

Yeah have tried all that, there's no nest logo when it restarts. Just the blank screen and flashing light at the top. I think it's bricked itself somehow tbh.

It's currently plugged into a phone charger so will see does it manage to right itself over the course of the day.

If it doesn't recharge and restart, the only other suggestion I can make at this stage is to open up the back cover, then the inner cover and remove the LiPo battery. If you have access to a multi meter check the terminal voltage on it. Should be 3.7V. If the battery is ok, unplugging for a while might be enough to reset the boot of the Nest. It's a long shot, but sometimes works on duff phones. Batteries are available on Amazon and elsewhere.

Mickeroo wrote: »

Cheers. It was installed by electric Ireland only a month ago so I would hope they'd replace it.

In that case just invoke the warranty. Could jusr be a dud.

I'm assuming this Drayton timer is a two zone electronic timer. Can post it's model no, plus a picture. You have a combi boiler, (gas?), so again I assume no HW cylinder, HW on demand?

So upstairs zone valve is on the HW timer, with boiler call/downstairs on the CH timer. I assume the boiler fires when an upstairs event occurs, and this is possible with those type of timers even when there is no direct connection to the boiler from zone valve switching, as by default these timers are supplied in gravity mode, (small switch at the back). What happens then is that the CH ON terminal goes live from a timed event from either zone, but the HW ON terminal is only used to operate the zone valve and bring in the upstairs rads. Normally, zone timers with a gravity mode are designed to be used with the CH circulation pump on zone 2, while zone timing 1 calls the boiler only thus heating HW by gravity, and CH if zone 1 has a timed event. It makes using smart controls with wireless stats a little trickier, as its not likely the zone valve relay microswitch is being used to call the boiler for upstairs events. If you want, you can check the back of the Grasslin to see if the switch is Gravity or Fully Pumped mode. This will determine if the zone fires the boiler independently of the CH terminal on the Grasslin, and will determine how it could be wired with smart stats and their relays.

championc wrote: »

I wired it myself when I installed the zone valve. It simply opens or closes on triggering, so does nothing with the system itself

So it depends on the CH timing to be on at the same time intervals in order to fire the boiler?

The only wiring necessary would be to bring back a switched live output from the Sunvic valve relay to fire the boiler for an upstairs timed event. This would give the upstairs a degree of independence from any timed downstairs events, though with your current setup, downstairs would now heat for both it's own and upstairs timed events, limited by the rad TRVs. If you were to install a general smart stat for the downstairs, and smart TRVs for the downstairs rads, it would now be possible to have independent control of downstairs as a zone, as the addition of the smart TRVs together act as a downstairs zone valve. This would be an easier installation option than having another zone valve fitted to isolate the downstairs CH flow. A single zone thermostat and receiver could be installed for general control of downstairs heating, with smart TRVs paired to this zone to call the boiler on an individual room basis through the stat relay. For upstairs, a similar setup, with a general thermostat operating the upstairs zone valve by its wireless relay, then a SL from the zone valve to call the boiler when the upstairs timing/temperature schedule dictates.
As the simplest option, you can replace your current timer with two smart stat receivers, Netatmo, Hive or Drayton Wiser. Tado also, but only one of these could be connected wirelessly to the receiver to fire the boiler, the other would need to be wired to operate the zone valve at the minimum.
In all cases, the upstairs zone will depend on the downstairs being active to supply heat, so a SL return from the zone valve is necessary in order to call the boiler for upstairs events. Your current TRVs will continue to limit room temperature anyway, and any or all of these can be replaced by smart TRVs to obtain individual room call for heat, or to turn off a room while the zone is heating. If you add smart TRVs to all rads, you will only require a single main stat receiver relay, as the upstairs zone valve could now be locked open, with upstairs flow control individualised on a room basis.
Perhaps a good and inexpesive start might be the Drayton Wiser Kit 3, with 2 wireless stats and a heat hub receiver. This would be a simple DIY install. Progress then to wiring the zone valve to call for heat independent of downstairs timing. Next, adding finer control with smart TRVs and so on. While the option to hear upstairs without sending flow to downstairs rads would require the addition of another plumbed in zone valve to give proper S plan plumbing, or smart TRVs on all downstairs rads, it's probably not a huge issue, as it would be seldom you might want to heat upstairs while completely zoning out downstairs, so additional plumbing probably not needed. You have the luxury of having existing TRV valve bodies already installed on your rads, reducing the cost of individual smart room control to the price of a DIY installed smart TRV, €60 per room more or less as offers appear. Start by looking at the smart stat brands listed above, all TRV capable, and figure out your preferences. For a full on TRV installation, the Honeywell Evohome packet might be attractive, if pricey. Posters here who have invested are very enthusiastic. You could spend hours just tinkering with the screen, instead of watching TV! If you're into smart home stuff, alarms, lights, cameras etc, you'll need to consider do you want a system that can have all these as extras on the brand app, or leave each to its own. Over to you now!

championc wrote: »

Wow, many thanks for that huge and concise answer. That's provided me with a lot of direction.

One final question if I may - would "smart" TRV's be much more accurate than my current ones ? Or is it more about being able to control rads in an instant, being able to lower, raise, or shut them off ?

Using Tado as an example, their wall stats have a granularity of 0.1°, TRVs are 1°. Normal mechanical stats require about plus or minus 3° to throw a switch. Mechanical TRVs are more analogue, closing the valve as the temperature rises and the active sensor material expands. Smart TRVs replicate this, but but using second order calculations will anticipate rising (or falling) room temperature by learning rate of change of temperature, and respond according to the brands own algorithms. That way the room is not cycling hot-cold. I had some great lecturers on dynamic control systems back in the 70's, it's a whole science in itself. Kind of stuff you never forget.

More than likely. Letting it drain it's internal battery is like a cold start, removing the battery would have the same effect, though would void warranty. At least it didn't end up as a pretty papepweight

Hey guys looking for advice on a back boiler stove installation. Ive been told that a system link heat genie needs to be installed with it. Ive contacted a few plumbers and none of them seemed confident about installing it. Or are there other options apart from the system link? Any reccomendations on companies or plumbers that a experienced in installing stoves with back boiler via system link? Thanks and PM me of course as per the rules.

deezell wrote: »

Are you running this along with a gas or oil boiler? Have you a HW cylinder or is your HW direct from the oil/ gas boiler?

Hya and thanks for the reply. A gas boiler and a hot water cylinder that were newly installed around 6 years ago knowing that a boiler stove would be installed one day. So all the pipework is there capped ready to go. Need an experienced installer.

deezell wrote: »

It depends on how the boiler and cylinder installation was carried out, and what pipework was installed to facilitate later connection of a stove. Is the gas boiler heated water system sealed, or vented? (attic head tank). If vented, this will simplify blending of the two heat sources. Does the cylinder have a spare unused coil? This would provide a direct heat sink for an active stove. It's all about having a mechanism to dissipate stove heat in the event of power failure, to reduce the risk of boiling the heating circuit water. There are some great schematics on NRG Awareness website, which detail the different methods used to blend heat sources. They manufacture a manifold which combines the heated water from both boilers, for distribution to the radiators and HW cylinder. There are many permutations of these systems, but the concept is easily understood.
https://www.nrgawareness.com/
They're based in Cork,

The systemlink heatgenie is a heat exchanger, which is required when the heated water of the gas/oil boiler is not vented, but is closed and pressurised. As the stove must be vented, the heated water from the stove can not be allowed to directly mix with the gas boiler system water. This is similar to the idea that the boiler heated water that enters your HW cylinder is isolated from the actual hot water you get from the cylinder out of the tap.
In order to then blend the heated water from the boiler to the heated water from the stove heat exchanger (or direct from the stove if the gas boiler is vented), a manifold or neutraliser box is needed. These are the models available from NRG Awareness. https://www.nrgawareness.com/product-category/nrg-zone-manifolds/
Systemlink have similar models, and some tube like models known as Spirozone.
https://www.plumbingproducts.ie/system-link/3741-systemlink-spirozone-5.html

The NRG Awareness version if the heat genie is this,
https://www.nrgawareness.com/product-category/system-interlinking/
Similarly expensive to the heat genie, it consists of a heat exchanger, pipe stat, and a couple of circulation pumps, with some pre made pipework. Not a lot of for nearly €800 it has to be said, a good plumber would pull it together from a couple of hundred euros of parts. This the basic principle of the heat exchanger.


Heres a link to a number of schematics for sealed boiler vented stove, as it probably more closely describes your system, assuming your gas boiler is sealed. If not, no heat exchanger required. This information should assist plumbers in assessing your system for upgrade.
https://www.nrgawareness.com/product/nrg-link/

Wow, great info thanks very much for the effort. If you can recommend anyone in and around Dublin thats experienced enough to install these I'd appreciate a PM. Thanks again, great info