Edision Optimuss OS 3 Plus

THE ALM · 22-01-2016 11:27AM

Having tried a few images I would have to say that egami is a non starter, crashes far too often. Tried opennfr without much luck either, just couldn't get it set up properly. Loaded up blackhole this morning although I'm away for the weekend so wont know how this goes for a day or two.

As said earlier, I have found hdfreaks to be very stable and had been running it for the last few months without any problems, if I could just stop the messing around with this box:rolleyes:

Partymack & Irreverent - can't say that I have ever had a problem with any recording or timeshift for that matter and have often had two recordings at once while watching a third channel. I do believe that the hard disk is formatted to Ext4 and as these are Linux boxes and Ext4 is a Linux format then this is maybe why it makes a difference. Not at the box so would need to confirm format.

On another note, has anybody been able to set up remote access to webif?

Currently have only 4G 'broadband' and I appear to have everything set up correctly but just can't access it. Have a ddns account set up and the router is successfully connected to this, have enabled http sharing on webif and given this a port number and have set up port forwarding on the router to this port number plus the ip address of the box. If anybody has any ideas on this they would be much appreciated

Partymack · 22-01-2016 06:31PM

THE ALM wrote: »

...
On another note, has anybody been able to set up remote access to webif?

Currently have only 4G 'broadband' and I appear to have everything set up correctly but just can't access it. Have a ddns account set up and the router is successfully connected to this, have enabled http sharing on webif and given this a port number and have set up port forwarding on the router to this port number plus the ip address of the box. If anybody has any ideas on this they would be much appreciated

Thanks for response on box crashing - interested to hear your experience. I have a USB key plugged in (s well as HDD) with my picons on it. Will try removing that this weekend see if it's the problem.

On remote logging in, took me a while to crack that. Sounds like yer almost there - on most routers you have to disable firewall to allow access remotely. Are you able to reach your routers log in page using the WAN IP address? Finally, when you can get the Router Log on page remotely you will need to add the port number to end of WAN address to view the box. E.g. 87.47.123.168:80(or whatever port you are forwarding to).

.G. · 22-01-2016 08:43PM

Partymack wrote: »

I'm having this problem generally with my OS3. It almost always happens if I've recorded a HD channel.

Wrote to supplier and they suggested reformatting HARDdrive to Ext4, mINE was in NTFS. Too early to say if problem is sorted yet.

My other problem is just box locking up, and screen going black. Hard reboot is only way to revive it. Again it seems to happen while watching a HD channel. I think the RAM is filling up and running out of space. Waiting for redone on this from Open ATV forums.

Anyone else having this 'box crashing' problem?

I had loads of lockups on my box using Open ATV images, I switched to HD freaks a few months back and it was much better but still did it from time to time. Am currently using Black Hole and its really good.

DopeTech · 23-01-2016 11:56AM

THE ALM wrote: »

Having tried a few images I would have to say that egami is a non starter, crashes far too often. Tried opennfr without much luck either, just couldn't get it set up properly. Loaded up blackhole this morning although I'm away for the weekend so wont know how this goes for a day or two.

Where did you download the blackhole image from? Wouldn't mind testing it out.

.G. · 23-01-2016 04:52PM

From here

http://www.sat-soft.net/forum/dm_eds/index.php?sid=f0e3f4935db930368337770e2583e566

You need to register to see the links.

.G. · 23-01-2016 04:52PM

del

Partymack · 27-01-2016 10:48AM

superg wrote: »

I had loads of lockups on my box using Open ATV images, I switched to HD freaks a few months back and it was much better but still did it from time to time. Am currently using Black Hole and its really good.

I think I've solved the problems that were bugging me most about the box:
• It was crashing quite a bit, usually if watching a HD channel.
• playback of recordings often caused it to crash.
• Recordings of HD channels played back with pixelated images, which became unwatchable.

I was using OPEN ATV 5.1, which I stuck with because visually it looks nicest and is easy to use but loaded with features.

I flashed OpenVix image and refornatted my Harddrive to EXT4. This has TRANSFORMED my box from a 'fingers crossed it won't crash' to a really reliable unit.

I'm not a huge fan of Skins in OpenVix, (I'm using the Blue HD) but nothing beats OPEN ATV's My MetrIx HD. But it is so stable. Recording 2 channels while watching a third etc etc. Plugins seem to integrate much better too.

If your struggling like I was I'd suggest moving to OPEN VIX.

championc · 27-01-2016 11:51AM

Think I'll take a copy of the MyMetrix skin first and then try OpenVix with the MyMetrix skin

Partymack · 27-01-2016 12:22PM

championc wrote: »

Think I'll take a copy of the MyMetrix skin first and then try OpenVix with the MyMetrix skin

Hey Champ,

Is it possible to 'take a copy' of the My Metrix Skin from OATV and then transfer it into OpenVix?

There is a MyMetrix skin you can download from plugin menu on OpenVix but when I did this it looked a bit cheep! Certainly needs some customisation as the colours are bit gawdy and the font is too small to read any menus, EPG, settings etc. If I had some time I was going to Start to tweek the skin till it started to resemble OATV version. But if I could just take a copy and swop.... Much better!

Kalyke · 27-01-2016 09:46PM

Partymack wrote: »

I think I've solved the problems that were bugging me most about the box:
• It was crashing quite a bit, usually if watching a HD channel.
• playback of recordings often caused it to crash.
• Recordings of HD channels played back with pixelated images, which became unwatchable.

I was using OPEN ATV 5.1, which I stuck with because visually it looks nicest and is easy to use but loaded with features.

I flashed OpenVix image and refornatted my Harddrive to EXT4. This has TRANSFORMED my box from a 'fingers crossed it won't crash' to a really reliable unit.

I'm not a huge fan of Skins in OpenVix, (I'm using the Blue HD) but nothing beats OPEN ATV's My MetrIx HD. But it is so stable. Recording 2 channels while watching a third etc etc. Plugins seem to integrate much better too.

If your struggling like I was I'd suggest moving to OPEN VIX.

Do you have a link or the Optimuss OS 3 Plus? The only image I could find on the Open Vix site was for the the OS-Mini

tippguy2 · 27-01-2016 10:00PM

Superg posted a link a few days ago,

Partymack · 28-01-2016 12:52AM

Kalyke wrote: »

Do you have a link or the Optimuss OS 3 Plus? The only image I could find on the Open Vix site was for the the OS-Mini

Yep... Here it's is

http://www.sat-soft.net/forum/dm_eds/index.php?sid=f212cde5fcd257b7cfd065503527f41e

Click the flashing red link on top of page.

It's actually a German Edision dedicated forum! They have downloads for all the major images but the OpenVix one is not actually supported by OpenVix team. I think the guys that run the site tweek an OpenVix image for the Edision. No bad thing as they are committed to their Optimuss boxes and have done a cracking job!

You have to register for the site to download image. I might try and put my image up on a day or two if you can hang about.

Zardoz · 28-01-2016 01:37AM

Partymack wrote: »

I think the guys that run the site tweek an OpenVix image for the Edision. No bad thing as they are committed to their Optimuss boxes and have done a cracking job!

Its probably the Vix image for the Technomate Nano 3T with the bootloader modified to run on the Edision.

They are the same receiver made by Dags so should run the same images.

tippguy2 · 28-01-2016 09:41AM

Zardoz wrote: »

Its probably the Vix image for the Technomate Nano 3T with the bootloader modified to run on the Edision.

They are the same receiver made by Dags so should run the same images.

Best image I've used to date on the os2+

jayo26 · 28-01-2016 10:06AM

tippguy2 wrote: »

Best image I've used to date on the os2+

Wrong thread for me but I'm using vix on solo2 and its also excellent.

Partymack · 28-01-2016 10:11AM

Zardoz wrote: »

Its probably the Vix image for the Technomate Nano 3T with the bootloader modified to run on the Edision.

They are the same receiver made by Dags so should run the same images.

Sounds likely, there is no references to Technomate receiver in the image however. All the messages, references, even image of the remote control refers to Optimuss. So they've done a thorough job on cloning it.

THE ALM · 29-01-2016 05:32PM

Partymack wrote: »

On remote logging in, took me a while to crack that. Sounds like yer almost there - on most routers you have to disable firewall to allow access remotely. Are you able to reach your routers log in page using the WAN IP address? Finally, when you can get the Router Log on page remotely you will need to add the port number to end of WAN address to view the box. E.g. 87.47.123.168:80(or whatever port you are forwarding to).

Still no joy with remote access. Have disabled the router firewall but still no luck. Everything seems set up ok but can't access router never mind the box.

Have a new router ordered so will see if I can set it up using this.

As mentioned I am trying to use this over Meteor 4G and wonder do they allow remote access?

Partymack · 30-01-2016 09:45PM

THE ALM wrote: »

Still no joy with remote access. Have disabled the router firewall but still no luck. Everything seems set up ok but can't access router never mind the box.

Have a new router ordered so will see if I can set it up using this.

As mentioned I am trying to use this over Meteor 4G and wonder do they allow remote access?

Have you figured out what your routers WAN IP address is? You should certainly be able to reach this when you try remotely to access. It's not gonna be the same as your LAN IP, which is probably 192.168.1.1 or the likes.

THE ALM · 31-01-2016 02:23PM

Partymack wrote: »

Have you figured out what your routers WAN IP address is? You should certainly be able to reach this when you try remotely to access. It's not gonna be the same as your LAN IP, which is probably 192.168.1.1 or the likes.

Have the router IP address ok. I think the issue maybe the fact that I have a 4G dongle plugged into the router and as such I have a different IP address for both. Not sure how I would work around this.

I am waiting on a new router which does away with the need for the dongle and hoping this will simplify the process.

dav32cs · 02-02-2016 01:58AM

Been trialing the Vix image and it seems the most stable so far. Only thing that seems missing compared to the official Vix image is that in the Softcam Manager it doesn't list out anything even if you have one installed.

Partymack · 03-02-2016 10:45AM

dav32cs wrote: »

Been trialing the Vix image and it seems the most stable so far. Only thing that seems missing compared to the official Vix image is that in the Softcam Manager it doesn't list out anything even if you have one installed.

Would agree it's most stable image I've tried. I prefer OPEN ATV for look/feel, but OpenVix is solid.

Don't agree with your final point.. Might need to check your folders.

dav32cs · 03-02-2016 11:57PM

Partymack wrote: »

Would agree it's most stable image I've tried. I prefer OPEN ATV for look/feel, but OpenVix is solid.

Don't agree with your final point.. Might need to check your folders.

Will check the screen again but everything runs OK so not big deal, just not visible in Softcam Manager menu for enabling startup/stop/start/ restart.

TSPanel or similar could just be installed if it was an issue for anyone (if it did replicate )and wanted these options.

Edit:Uninstalled and reinstalled and are appearing now.

Partymack · 09-02-2016 12:31PM

Lads,

Picked this up from the Amiko forum. Great new skin based on sky box.

It's not the BLUE HD that is available in OpenVix feeds - it's ten times better!

http://www.techkings.org/zgemma-star-2s/84606-slyk-1-hd-sly-skin-version-3-now-available.html

Been using on OpenVix on my OS3 since weekend and it is flawless. Also really good support and customisation options on the pages where you download it.

Just a thought for those using or used to a Sky skin.

Partymack · 09-02-2016 03:47PM

Anyone got streaming to iPhone working on Optimuss box yet?

I've got Dreambox Live App but everyone I open it, it displays a screenshots active channel and then the app closes!

I have to be really quick on the buttons to get yo settings, I've played around with them all and still can't get it to work.

Anyone using on Edidion boxes?

dav32cs · 11-02-2016 01:16AM

Partymack wrote: »

Anyone got streaming to iPhone working on Optimuss box yet?

I've got Dreambox Live App but everyone I open it, it displays a screenshots active channel and then the app closes!

I have to be really quick on the buttons to get yo settings, I've played around with them all and still can't get it to work.

Anyone using on Edidion boxes?

Download Vu Player.

Pretty simple when compared to Dreamdroid but it does the job for viewing your channels or recordings.

Partymack · 11-02-2016 10:22AM

dav32cs wrote: »

Download Vu Player.

Pretty simple when compared to Dreamdroid but it does the job for viewing your channels or recordings.

Hey Dav32,

Looks like just what I need!

Will have a go this weekend and see if it does the job.

Thanks

jayo26 · 11-02-2016 12:19PM

Partymack wrote: »

Hey Dav32,

Looks like just what I need!

Will have a go this weekend and see if it does the job.

Thanks

Another one that I find works better is dream player on Android id say it is same on ios check it out too.

AtomsForPeace · 11-02-2016 11:24PM

Partymack wrote: »

Lads,

Picked this up from the Amiko forum. Great new skin based on sky box.

It's not the BLUE HD that is available in OpenVix feeds - it's ten times better!

Been using on OpenVix on my OS3 since weekend and it is flawless. Also really good support and customisation options on the pages where you download it.

Just a thought for those using or used to a Sky skin.

Cheers for that.. Tried the skin there and 'tis pretty sweet. A big improvement than the default one from freetv.

This whole thread has been pretty useful...
Good job boardies!

Partymack · 12-02-2016 10:14AM

dav32cs wrote: »

Download Vu Player.

Pretty simple when compared to Dreamdroid but it does the job for viewing your channels or recordings.

I tried this last night and it seemed to be a bit stuttery. I was just using on my Lan so speeds etc. Should be ok. It struggled to change channel, audio would come in first then sometimes picture. Maybe need to change done settings.., any thoughts?

jayo26 wrote: »

Another one that I find works better is dream player on Android id say it is same on ios check it out too.

Can't find this in App Store, maybe there's is no iOS version?

jayo26 · 12-02-2016 10:47AM

Partymack wrote: »

Can't find this in App Store, maybe there's is no iOS version?

Ah right sorry mate its probably not there then I been finding it excellent for herself watching the soaps recorded and stuff.

Edision Optimuss OS 3 Plus

Comments