Advertisement
If you have a new account but are having problems posting or verifying your account, please email us on hello@boards.ie for help. Thanks :)
Hello all! Please ensure that you are posting a new thread or question in the appropriate forum. The Feedback forum is overwhelmed with questions that are having to be moved elsewhere. If you need help to verify your account contact hello@boards.ie
Hi there,
There is an issue with role permissions that is being worked on at the moment.
If you are having trouble with access or permissions on regional forums please post here to get access: https://www.boards.ie/discussion/2058365403/you-do-not-have-permission-for-that#latest

MAXIS PC4020 + HKC Bell problem

  • 18-05-2014 3:02pm
    #1
    rucanunes
    Registered Users Posts: 5 ✭


    Hello,

    Could someone please tell me how to connect these two systems?
    I have something wrong; when the alarm it's activated the bell rings for 5 seconds (no blue light) but than flashes a blue light and goes silent.

    All the other functions of the alarm are working fine.
    This is an old installation that it was not made by me.

    I really appreciate some help please!?

    Regards,
    Raul Nunes


Comments

  • #2
    KoolKid
    Moderators, Home & Garden Moderators, Technology & Internet Moderators Posts: 24,789 Mod ✭✭✭✭KoolKid


    Can you tell us what way you have it wired at the moment?
    I sent you the manual as well. maybe that will help you.


  • #3
    rucanunes
    Registered Users Posts: 5 ✭rucanunes


    Thank you very much.
    I have the manual of the alarm, but I don't have the manual of the bell. :-(

    This is how I connected:

    Bell
    Alarm

    External +
    AUX + (Red always positive)
    SAB Hold
    AUX – (Black always negative)
    Strobe -
    BELL – (Negative when in alarm)
    Strobe +
    AUX + (Red always positive)

    I cannot post images from the circuits because I'm a new user! :-(

    Regards!


  • #4
    KoolKid
    Moderators, Home & Garden Moderators, Technology & Internet Moderators Posts: 24,789 Mod ✭✭✭✭KoolKid


    Have you the bell negative from the SABB connected to anything at the panel?


  • #5
    rucanunes
    Registered Users Posts: 5 ✭rucanunes


    No! Can you tell me how to connect the boar to the bell please?


  • #6
    KoolKid
    Moderators, Home & Garden Moderators, Technology & Internet Moderators Posts: 24,789 Mod ✭✭✭✭KoolKid


    Is there a bell - output ?
    If not you need to programme one to switch negative when the alarm activates..


  • Advertisement
  • #7
    rucanunes
    Registered Users Posts: 5 ✭rucanunes


    Yes, there's a Bell- output.


  • #8
    KoolKid
    Moderators, Home & Garden Moderators, Technology & Internet Moderators Posts: 24,789 Mod ✭✭✭✭KoolKid


    That should be a switched negative for an alarm .
    Connect that to Bell - on the external bell.


  • #9
    rucanunes
    Registered Users Posts: 5 ✭rucanunes


    No I have another problem, this one is a little strange!!

    I have zone 1 and zone 3 connected to the board.

    Zone 1 it's working fine!

    Zone 2 deleted.

    Zone 3 it's somewhat strange!!!

    I have zone 3 connected like this:

    Red
    AUX+

    Black
    AUX –

    Blue
    Z3

    Brown
    COM

    The sensor has a 5600 resistor between blue and brown cables.

    The sensot warns me if someone walks by that zone (two beeps at the keypad)

    But when I try to turn the alarm on, it says "Close zone 3 before arming"....

    If I change EOL options it tells me "Short in zone 3"

    I also have an exclamation point (!) in zone 3.

    Any suggestions on how to fix this problem?

    Regards!

    Raul Nunes


Advertisement