Advertisement
Help Keep Boards Alive. Support us by going ad free today. See here: https://subscriptions.boards.ie/.
If we do not hit our goal we will be forced to close the site.

Current status: https://keepboardsalive.com/

Annual subs are best for most impact. If you are still undecided on going Ad Free - you can also donate using the Paypal Donate option. All contribution helps. Thank you.
https://www.boards.ie/group/1878-subscribers-forum

Private Group for paid up members of Boards.ie. Join the club.

Take down & rebuild hay shed.

  • 28-07-2021 03:56PM
    #1
    Registered Users, Registered Users 2 Posts: 236
    ✭✭


    Hello

    I've been thinking about taking down a seven Bay hay shed and transporting it two miles and rebuilding it. Anyone know of the costs involved? Roscommon area.



Welcome!

It looks like you're new here. Sign in or register to get started.

Comments

  • Registered Users, Registered Users 2, Paid Member Posts: 2,683 DBK1
    ✭✭✭


    I don’t know anything about the costs involved but it is a job I’ve done with lads a couple of times. The advice I would give is to prepare well for it. Draw a sketch of the shed yourself and take accurate measurements of the distances between every pillar. Mark that on the sketch. Then as the shed is being dismantled number every sheet as it comes down and stack them in order. Again mark on your sketch where the numbers correspond to.

    Basically the simplest way to rebuild it is to put everything back up in exactly the same order and position as it came down and that will make the job a whole lot easier.

    Best of luck with it, 7 bays is a fine size shed.



  • Registered Users, Registered Users 2 Posts: 236 Waternotsoda
    ✭✭


    Thanks for replying. How did u dig up the uprights? The shed went up in the 80s and was added to down the years. So some of the uprights were placed in a hole and then it was filled in.



  • Registered Users, Registered Users 2, Paid Member Posts: 1,557 Tileman
    ✭✭✭


    The uprights are usually just cut off at ground level



  • Registered Users, Registered Users 2 Posts: 2,289 148multi
    ✭✭✭


    Lift them after shed is dismantled, with the lift arm of a tractor, your looking at the guts of a grand worth of steel. The lump af concrete that's around them will break up, if your having problems, cut a line through the concrete in line with the h iron at opposite sides



  • Registered Users, Registered Users 2 Posts: 236 Waternotsoda
    ✭✭


    Thanks



  • Advertisement
  • Moderators, Society & Culture Moderators Posts: 12,934 blue5000
    Mod ✭✭✭✭


    I’ve never done one but lining up the holes on the roof sheets can be the hardest part to get right, tube of silicone might be needed to block old holes. Let us know how it goes.

    If the seat's wet, sit on yer hat, a cool head is better than a wet ar5e.



  • Registered Users, Registered Users 2 Posts: 236 Waternotsoda
    ✭✭


    Got it taken down and transported for €1,800.



  • Registered Users, Registered Users 2, Paid Member Posts: 20,874 Bass Reeves
    ✭✭✭✭


    How much to re-erected. That is a very good price( half or more than I would expect) to take it down and transport.

    Was being quoted 2k for labour alone to erect a lean-to onto a two bay shed last year and I then could not get him to do it.

    Slava Ukrainii



  • Registered Users, Registered Users 2 Posts: 236 Waternotsoda
    ✭✭


    It will be rebuilt over the summer. He will do a price for me then.



  • Registered Users, Registered Users 2 Posts: 11,623 patsy_mccabe
    ✭✭✭✭


    If I was doing it, I'd get a laser level and mark all the uprights at about eye level. That would be a great help when lining them up again. No small job taking down and rebuilding a shed like that.



  • Advertisement
  • Registered Users, Registered Users 2, Paid Member Posts: 3,283 Good loser
    ✭✭✭


    Have a 50/60 year old round roof shed. 3" angle iron purlins on steel frame. Sheets secured with many J bolts.

    Would like to replace roof sheets and maybe do more. Any advice? What are prospects that angle iron is okay.

    Would it be done off scaffolding or off hoists?



Welcome!

It looks like you're new here. Sign in or register to get started.
Advertisement