Advertisement
If you have a new account but are having problems posting or verifying your account, please email us on hello@boards.ie for help. Thanks :)
Hello all! Please ensure that you are posting a new thread or question in the appropriate forum. The Feedback forum is overwhelmed with questions that are having to be moved elsewhere. If you need help to verify your account contact hello@boards.ie
Hi there,
There is an issue with role permissions that is being worked on at the moment.
If you are having trouble with access or permissions on regional forums please post here to get access: https://www.boards.ie/discussion/2058365403/you-do-not-have-permission-for-that#latest

Emmersion not heating water

  • 14-06-2018 10:48am
    #1
    Registered Users, Registered Users 2 Posts: 3,597 ✭✭✭


    Hello all,


    A family members immersion is not heating water, Sink or bath. She had a boiler stove fitted roughly 1 year ago with a new tank etc etc. A turned the dial back to reset and back up to 70 on the gizmo on top of the tank but this didnt do anything. Is there another reset button or trip switch? When the immersion is switched on the red light illuminates fine. Ill attach some pictures that might help sort this.


    If its not an simple fix would it be a plumber or electrician thats needed?


    Also should she call back the shop she bought the system off and see do they cover this under warranty?2uix9bt.jpg


    6ej14p.jpg


Comments

  • Registered Users, Registered Users 2 Posts: 17,176 ✭✭✭✭Sleeper12


    Also should she call back the shop she bought the system off and see do they cover this under warranty?


    Roughly a year? Is that 10 months or 14 months? Most come with a 12 month warranty


  • Registered Users, Registered Users 2 Posts: 3,597 ✭✭✭Richard tea


    Sleeper12 wrote: »
    Roughly a year? Is that 10 months or 14 months? Most come with a 12 month warranty




    I would have to check with her.


  • Registered Users, Registered Users 2 Posts: 8,565 ✭✭✭K.Flyer


    6ej14p.jpg

    Turn off electricity to the immersion.
    On the immersion thermostat, turn the dial back to midway between the 55 and the 70. (C position)
    Then, using a pen (or something similar), push hard on the very small Red button above the word Reset. You should hear or feel a click as the immersion resets.
    Restore power to the immersion and check in 20 minutes for hot water.


  • Registered Users, Registered Users 2 Posts: 5,121 ✭✭✭TomOnBoard


    K.Flyer wrote: »
    Turn off electricity to the immersion.
    On the immersion thermostat, turn the dial back to midway between the 55 and the 70. (C position)
    Then, using a pen (or something similar), push hard on the very small Red button above the word Reset. You should hear or feel a click as the immersion resets.
    Restore power to the immersion and check in 20 minutes for hot water.

    +1


  • Registered Users, Registered Users 2 Posts: 3,597 ✭✭✭Richard tea


    Spot on k flyer. That worked. I suppose if it trips again or a number of times it could be an issue


  • Advertisement
  • Registered Users, Registered Users 2 Posts: 8,565 ✭✭✭K.Flyer


    Spot on k flyer. That worked. I suppose if it trips again or a number of times it could be an issue

    Most likely the cause is the high temperature of the circulated water from the stove is exceeding the high limit setting on the thermostat causing it to trip out, therefore it is likely to happen again when the stove comes back into use.
    If it was to re-occur while only using the immersion, then I would suggest changing the thermostat for a new one.


Advertisement