Cupti users, are you satisfied?

aka7

I have a Cupti (not cupti 2) for about a week.
I was planning to move up from the old Evod. I was planning to use it MTL around 10-15 W.
Is this the right range for 1.6 ohm?

I tried both coils that were part of the pack and an extra new one 1.5 ohm.
I am testing using Liqua liquids 9-12mg nic.
Also tried some different juices from British LiQuid where any bottles cost £1.00, I think they are making them. These ones do not seem to work for me at all, any bottle I tried. I got what I paid for it looks.

In all cases I have little or very little vapour and hard on the throat (at times nasty) compared to the old Evod.
I can see the battery and juice is going down faster that I would expect since I am mostly experimenting, not able to use it ongoing because of throat harshness and lack of steam. One battery (LGDBHE41865) emptied from full, second battery (LG 18650HG2) nearly empty. I would say after about 1-200 drags over a week. Is this normal?

Are my batteries ok for Cupti?
If there is a proved e-juice that works with cupti especially MTL? I think what I tried so far are around 50/50 VG/PG.
I am willing to try some proved juices before concluding my Cupti a failure.

Any advice would be appreciated, especially if any Cupti users are around.

youdipstick

Your range for the 1.6 coil is perfect...

Can't help you on the Cupti,never owned one,sorry...

They are getting old now,so you may not get an answer...

aka7

Ok, thanks youdipstick.

I should have asked here for MTL setup suggestions before went ahead an purchased the cupti.
Also from the Cupti videos, I did not expect to be as heavy.

It does look like most vapers are vaping direct to lung now days.
Is the 0.5 ohm that I think needs higher wattage not meant to be "right" for MTL ?

youdipstick

aka7 wrote: »

Ok, thanks youdipstick.

I should have asked here for MTL setup suggestions before went ahead an purchased the cupti.
Also from the Cupti videos, I did not expect to be as heavy.

It does look like most vapers are vaping direct to lung now days.
Is the 0.5 ohm that I think needs higher wattage not meant to be "right" for MTL ?

Anything below 0.6 is sub-ohming now,it use to be 1.0ohm but with newer type coils out today changes the way we vape the different resistances,so sub-ohming is used for DL inhaling & more power is needed but the only downside is,your juice will disappear quickly,most of us that do sub-ohming normally mix their own juice,a lot cheaper that way.I get more satisfaction from DL vaping & using high VG & 6mg Nic strength,I do like MTL on certain juices at 18mg 50/50 PG/VG,depends what mood I'm in:D:D:D

You say the Cupti is a real heavy mod,I was just thinking,my mate might have one,I'll get back to you on that.

youdipstick

youdipstick wrote: »

Anything below 0.6 is sub-ohming now,it use to be 1.0ohm but with newer type coils out today changes the way we vape the different resistances,so sub-ohming is used for DL inhaling & more power is needed but the only downside is,your juice will disappear quickly,most of us that do sub-ohming normally mix their own juice,a lot cheaper that way.I get more satisfaction from DL vaping & using high VG & 6mg Nic strength,I do like MTL on certain juices at 18mg 50/50 PG/VG,depends what mood I'm in:D:D:D

You say the Cupti is a real heavy mod,I was just thinking,my mate might have one,I'll get back to you on that.

It wasn't a cupti,it was a Smoant V1 which is as heavy as an anvil:D:D

https://www.youtube.com/watch?v=fzvAnaj5j5I