Advertisement
Help Keep Boards Alive. Support us by going ad free today. See here: https://subscriptions.boards.ie/.
If we do not hit our goal we will be forced to close the site.

Current status: https://keepboardsalive.com/

Annual subs are best for most impact. If you are still undecided on going Ad Free - you can also donate using the Paypal Donate option. All contribution helps. Thank you.
https://www.boards.ie/group/1878-subscribers-forum

Private Group for paid up members of Boards.ie. Join the club.

Any ideas on how to wire up my switch panel?

  • 06-08-2014 06:52PM
    #1
    Registered Users, Registered Users 2 Posts: 311 ✭✭


    I have no clue how to wire up this, I've tried different ways but can't seem to get it figured out!


Comments

  • Moderators, Motoring & Transport Moderators, Sports Moderators, Paid Member Posts: 6,385 Mod ✭✭✭✭fergal.b


    It should be something like this but I can't see any feed out on your switches, is there any slots that a male spade connector will fit in.

    HelmWiring2.jpg

    Spade connector.

    1_1225125372.jpg


  • Registered Users, Registered Users 2 Posts: 311 ✭✭whacker1982


    oh god getting dizzy looking at this, but yes thats pretty much the same layout as mine, the spade connector is at the bottom of the switch, cheers fergal ill give it a go :)


  • Registered Users, Registered Users 2 Posts: 311 ✭✭whacker1982


    ok i think i understand it now, but what the trim tab line for going into a 20amp fuse and then going no where dont understand that one


  • Moderators, Motoring & Transport Moderators, Sports Moderators, Paid Member Posts: 6,385 Mod ✭✭✭✭fergal.b


    If you are running electric trim tabs you will need two separate switches not the type you'd see on a switch panel more like this.

    Waterproof%20Rocker%20Switch,%20LS3000.jpg


  • Registered Users, Registered Users 2 Posts: 311 ✭✭whacker1982


    would i get a main accessory harness plug in a motor factor?


  • Advertisement
  • Moderators, Motoring & Transport Moderators, Sports Moderators, Paid Member Posts: 6,385 Mod ✭✭✭✭fergal.b


    I would stay with marine grade wire instead of auto and make up your own harness as you only have a few switches
    4gauge = 160A
    6g = 120A
    8g = 80A
    10g = 60A
    12g = 45A
    14g = 35A 14 gauge should do most of your electrics maybe going a bit higher for lights
    16g = 25A
    18g = 20A


  • Registered Users, Registered Users 2 Posts: 311 ✭✭whacker1982


    went at it there now, where do the two cables coming off the lights go into the switch panel? its all lights ill be hooking up, 4 in total all with two cables coming out of the lights, but where and how do they fit into the switch panel?


  • Moderators, Motoring & Transport Moderators, Sports Moderators, Paid Member Posts: 6,385 Mod ✭✭✭✭fergal.b


    One wire will go to your negative bar bus "black in the photo above" and the other will go to the switch on the opposite side to where the power goes in, this will only be live when you turn on the switch.



    .


  • Registered Users, Registered Users 2 Posts: 311 ✭✭whacker1982


    fergal.b wrote: »
    One wire will go to your negative bar bus "black in the photo above" and the other will go to the switch on the opposite side to where the power goes in, this will only be live when you turn on the switch.



    .

    Ah, I though the bus was the battery, that's how bad I am with electrics, the bus is the bar under each switch and fuse, so the harness plug goes to the battery?


  • Moderators, Motoring & Transport Moderators, Sports Moderators, Paid Member Posts: 6,385 Mod ✭✭✭✭fergal.b


    The bus bar is like this and all your negatives run to it.

    Buss-bar-300x184.jpg

    Not to be confused with a pub in Skerries :D


    4148243269_d3a86ca4ca.jpg


  • Advertisement
  • Registered Users, Registered Users 2 Posts: 311 ✭✭whacker1982


    fergal.b wrote: »
    The bus bar is like this and all your negatives run to it.

    Buss-bar-300x184.jpg

    Not to be confused with a pub in Skerries :D


    4148243269_d3a86ca4ca.jpg

    I feel like going there now after that slip up :/ thanks fergal


Advertisement