Advertisement
Help Keep Boards Alive. Support us by going ad free today. See here: https://subscriptions.boards.ie/.
If we do not hit our goal we will be forced to close the site.

Current status: https://keepboardsalive.com/

Annual subs are best for most impact. If you are still undecided on going Ad Free - you can also donate using the Paypal Donate option. All contribution helps. Thank you.
https://www.boards.ie/group/1878-subscribers-forum

Private Group for paid up members of Boards.ie. Join the club.

Quasar RDA Clone Leaking Through 510 Connection

  • 16-05-2014 11:32AM
    #1
    masonchat
    Registered Users, Registered Users 2 Posts: 667 ✭✭✭


    So i just noticed the 510 well on my sentinel M16 is full of juice , my quasar RDA leaks through the 510 contact pin.

    I tried to tighten the screw, but the whole center post just turns with it, what stupidity this piece could have been made solid and thus leak proof.

    Anyway it is what it is now, i dont want to grab canter post with a pliers and try to screw the pin up as im not familiar with how its built and i dont want to completely break it.

    Has anyone any tips for me on how to stop it leaking ? please


Comments

  • #2
    jousting with chairs
    Registered Users, Registered Users 2 Posts: 935 ✭✭✭jousting with chairs


    There's a bit on the Ft forum about it but no fix yet.

    Came across this one but he didn't say whether it worked or not.

    http://www.rebuildable-ecigs.com/showthread.php?2235-Quasar-by-Cosmic-Innovations


  • #3
    masonchat
    Registered Users, Registered Users 2 Posts: 667 ✭✭✭masonchat


    Thanks jousting


  • #4
    M00lers
    Registered Users, Registered Users 2 Posts: 1,503 ✭✭✭M00lers


    Just spotted this. That's a bummer. I'd grab the centre post with needle nose pliers and tighten the screw in the 510. Be careful though, but that should sort it out. I'll try mine later.


  • #5
    M00lers
    Registered Users, Registered Users 2 Posts: 1,503 ✭✭✭M00lers


    moolers2000 wrote: »
    Just spotted this. That's a bummer. I'd grab the centre post with needle nose pliers and tighten the screw in the 510. Be careful though, but that should sort it out. I'll try mine later.

    Hi Masonchat, I've just tried mine and I reckon you should be able to fix it. What I did was gently grab the bottom of the positive post with needle nose pliers and then tighten the screw in the 510. As you noticed it will spin unless you hold onto the post firmly. Let me know how you get on.


  • #6
    masonchat
    Registered Users, Registered Users 2 Posts: 667 ✭✭✭masonchat


    Hi moolers i will try that tomorrow thanks , its not the end of the world i just rebuilt it for now with more cotton so juice isnt sitting on the deck and i stuffed around the post with cotton ill see how that goes.

    The link that jousting put up , a fella took his apart and the center post is push fitted


  • Advertisement
  • #7
    M00lers
    Registered Users, Registered Users 2 Posts: 1,503 ✭✭✭M00lers


    masonchat wrote: »
    Hi moolers i will try that tomorrow thanks , its not the end of the world i just rebuilt it for now with more cotton so juice isnt sitting on the deck and i stuffed around the post with cotton ill see how that goes.

    The link that jousting put up , a fella took his apart and the center post is push fitted

    Most positive posts and negative posts are press fit. Unless you go for a Zenith v2 with welded negative posts or a Tobh with the negative posts milled out of the base. It's standard practice really. Try to tighten it. Worth a shot.


Advertisement