Pushfit (John Guest fittings) pipe repair kit?

Saruman

Anyone know where I can find these in Ireland? Or somewhere that ships here?

Screwfix does not according to their website.

I have a burst pipe to repair. It's a copper pipe so is this even suitable?

Joey the lips

I dont know to be honest. Heatmerchants are john guest agents

But if it were me i would be buying

2 no 1/2" 310's and a meter of pex

if its metric

I would buy 2 no 610's as well and just change the olives

Dont forget the pex inserts.

Sparkpea

b&q would normally do the likes of that

ronaneire

B & Q wouldn't stock JG fittings. I second what Joey said, be cheaper then JG

Sparkpea

really their website says they do.

ronaneire

Sparkpea wrote: »

really their website says they do.

Who's site?

Saruman

Joey the lips wrote: »

I dont know to be honest. Heatmerchants are john guest agents

But if it were me i would be buying

2 no 1/2" 310's and a meter of pex

if its metric

I would buy 2 no 610's as well and just change the olives

Dont forget the pex inserts.

I don't know what any of that means

I do know what John Guest is because I use them in my Kegerator for my beer lines.

Joey the lips

Saruman wrote: »

I don't know what any of that means

I do know what John Guest is because I use them in my Kegerator for my beer lines.

1/2" 310s are straight connectors with brass nuts

610s are the metric equivialient which you might need

Pex is short for qualpex pipe which is pipe used instead of copper.

slavetothegrind

http://www.diy.com/diy/jsp/bq/nav.jsp?fh_location=//catalog01/en_GB/categories<{9372015}/categories<{9372046}/categories<{9372180}/specificationsProductType=plumbing_fittings&amp;fh_reftheme=promo_161448391,seeall,//catalog01/en_GB/categories<{9372015}/categories<{9372046}/categories<{9372180}&amp;fh_refview=summary&amp;icamp=ns_10

that shows you all you need, 2 straight connectors and a bit of pipe

but more importantly what is a kegerator and how can it improve my life:D

...ok followed your sig links much reading to do...may have questions later....

martin46585

you could try a brass repair fitting, looks just like a normal 310 (brass compression fitting) but is approx 4" long and has no centre stops, perfect for burst pipes and the likes, as long as the 'split' is no more than 2" long, just cut the pipe slide the fitting on and tighten up, available in all good builders providers

Drake66

Joey the lips wrote: »

1/2" 310s are straight connectors with brass nuts

610s are the metric equivialient which you might need

Pex is short for qualpex pipe which is pipe used instead of copper.

Would you have to use a compression fitting or would a couple of tectite straight connectors do the job? I'm trying to learn a bit about plumbing!

Joey the lips

Drake66 wrote: »

Would you have to use a compression fitting or would a couple of tectite straight connectors do the job? I'm trying to learn a bit about plumbing!

I have never seen metric tec tite in ireland but yes if its imperial yes tectite will work fine. It would be simular to the john geest fitting which is also push fit.

Sparkpea

I was browsing a holiday homes website and screwfix ad came up on it with this link..

http://www.screwfix.com/prods/14767/Plumbing/Flexible-Hoses/15mm-Pipe-Repair-Push-Fit?cm_mmc=Criteo-_-Plumbing-_-Flexible%20Hoses-_-15mm%20Pipe%20Repair%20Push%20Fit&source=aw

is that what your looking?

Saruman

Well I found all the stuff I needed at Atlantic. More expensive than the UK of course but at least I got it.
I repaired the burst pipe this morning and no more leaks. Only thing is, when I tested it there was no heat from the radiator that the plumber terminated. I rejoined the pipes (cold and hot) and cut out/replaced the burst part.

Odd.... will worry about it some other time.

edit never mind, it was probably thermostat keeping it off as it was already warm enough. It is working now that the heating has kicked in again on the regular timer.

CHLuke2240

Ive bought John Guest fittings from Aquasoft Ireland in dublin. There located in santry and have a good selection.

Dtp1979

CHLuke2240 wrote: »

Ive bought John Guest fittings from Aquasoft Ireland in dublin. There located in santry and have a good selection.

If it's still leaking by now then he has a serious problem