Advertisement
If you have a new account but are having problems posting or verifying your account, please email us on hello@boards.ie for help. Thanks :)
Hello all! Please ensure that you are posting a new thread or question in the appropriate forum. The Feedback forum is overwhelmed with questions that are having to be moved elsewhere. If you need help to verify your account contact hello@boards.ie
Hi all! We have been experiencing an issue on site where threads have been missing the latest postings. The platform host Vanilla are working on this issue. A workaround that has been used by some is to navigate back from 1 to 10+ pages to re-sync the thread and this will then show the latest posts. Thanks, Mike.
Hi there,
There is an issue with role permissions that is being worked on at the moment.
If you are having trouble with access or permissions on regional forums please post here to get access: https://www.boards.ie/discussion/2058365403/you-do-not-have-permission-for-that#latest

Extension Lead

  • 02-06-2020 12:12pm
    #1
    tombrown
    Registered Users, Registered Users 2 Posts: 472 ✭✭


    I have (had) a 50M extension lead. The lads fitting our gate used it (fully extended) to try & run their welder and it tripped. I have checked it out and the fuse in the plug is fine and I can measure 220V at that end but when I open up the sockets the voltage is only about 48V (I checked both sides of the thermal trip)

    So now I am at a loss - I assume this must mean damage to the wires somewhere along the cable, is that right? To my simple mind it should read either 220V or 0V, not something between.

    Any ideas on how/if I can fix this, or do I just have to splash out on a new one?


Comments

  • #2
    coylemj
    Registered Users, Registered Users 2 Posts: 25,495 ✭✭✭✭coylemj


    What's the (amps) rating on the extension lead and what fuse is in the plug? Did you ask the lad with the welder what current he was going to draw before you loaned him your extension lead?


  • #3
    tombrown
    Registered Users, Registered Users 2 Posts: 472 ✭✭tombrown


    Extension lead rated for 3000W, 230V (so 13amp) when fully extended. It has a 13A fuse. It was fully extended when it tripped

    No I didn't ask him what current the welder would use, though if it was trying to pull more than 13A I would expect that the fuse would have blown first. Any way, rightly or wrongly, that ship has sailed

    So whats the prognosis?


  • #4
    brightspark
    Registered Users, Registered Users 2 Posts: 2,637 ✭✭✭brightspark


    Most likely a broken connection somewhere. check the continuity of each core.


  • #5
    adrian92
    Registered Users, Registered Users 2 Posts: 566 ✭✭✭adrian92


    Perhaps the voltage you are measuring an induced voltage?


  • #6
    autumnalcore
    Registered Users, Registered Users 2 Posts: 838 ✭✭✭autumnalcore


    Extension lead probably got caught in the door at some stage, gust of wind and a nice sharp door edge look for kink and nick in the cable.


  • Advertisement
  • #7
    adrian92
    Registered Users, Registered Users 2 Posts: 566 ✭✭✭adrian92


    tombrown wrote: »
    I have (had) a 50M extension lead. The lads fitting our gate used it (fully extended) to try & run their welder and it tripped. I have checked it out and the fuse in the plug is fine and I can measure 220V at that end but when I open up the sockets the voltage is only about 48V (I checked both sides of the thermal trip)

    So now I am at a loss - I assume this must mean damage to the wires somewhere along the cable, is that right? To my simple mind it should read either 220V or 0V, not something between.

    Any ideas on how/if I can fix this, or do I just have to splash out on a new one?

    Looks like a btoken neutral ( the 48 volts was probably induced) Not real. Others better than I could help. Moderator always good.
    A broken neutral


  • #8
    tombrown
    Registered Users, Registered Users 2 Posts: 472 ✭✭tombrown


    Thansk for all the suggestions - I'll check it out with a m/meter tonight


Advertisement