Advertisement
If you have a new account but are having problems posting or verifying your account, please email us on hello@boards.ie for help. Thanks :)
Hello all! Please ensure that you are posting a new thread or question in the appropriate forum. The Feedback forum is overwhelmed with questions that are having to be moved elsewhere. If you need help to verify your account contact hello@boards.ie
Hi all! We have been experiencing an issue on site where threads have been missing the latest postings. The platform host Vanilla are working on this issue. A workaround that has been used by some is to navigate back from 1 to 10+ pages to re-sync the thread and this will then show the latest posts. Thanks, Mike.
Hi there,
There is an issue with role permissions that is being worked on at the moment.
If you are having trouble with access or permissions on regional forums please post here to get access: https://www.boards.ie/discussion/2058365403/you-do-not-have-permission-for-that#latest

How to locate pipes before fixing loose floorboards

  • 29-11-2020 8:55pm
    #1
    madds
    Registered Users, Registered Users 2 Posts: 1,884 ✭✭✭


    We have tongue and groove floors upstairs in a 20 y/o house. Some of the bedroom floors are really noisy when they're walked on so I want to fix them.

    Before I start fixing the boards to the joists with screws is there any way I can check to see where the pipework is wihtout having to first lift the boards?

    Note floors are tongue and groove so I can't slip a blade down between the boards to check for pipes. The pipes are a type of PVC/CPVC I think.

    Thanks for helping!


Comments

  • #2
    Calahonda52
    Registered Users, Registered Users 2 Posts: 12,561 ✭✭✭✭Calahonda52


    what makes you think they are there?

    “I can’t pay my staff or mortgage with instagram likes”.



  • #3
    LenWoods
    Registered Users, Registered Users 2 Posts: 617 ✭✭✭LenWoods


    madds wrote: »
    We have tongue and groove floors upstairs in a 20 y/o house. Some of the bedroom floors are really noisy when they're walked on so I want to fix them.

    Before I start fixing the boards to the joists with screws is there any way I can check to see where the pipework is wihtout having to first lift the boards?

    Note floors are tongue and groove so I can't slip a blade down between the boards to check for pipes. The pipes are a type of PVC/CPVC I think.

    Thanks for helping!

    Hi,
    I recommend using self tapping wood screws and some knee pads, there are also Philips head adapters available for a drill where the outter part "DeWalt" logo doesn't rotate; meaning you can hold it while drilling.

    pmgPVZtBj

    Foaming around the edge of the floor while you have it stepped out; also helps reduce heat loss.

    pnSkWo4Cj

    Anyway; to answer your question, a wall stud finder which detects studs, pipes and cables will also work on the floor, available from Amazon fairly cheap, I have a Stanley branded unit.


  • #4
    theteal
    Registered Users, Registered Users 2 Posts: 7,593 ✭✭✭theteal


    I did this recently on the landing before new carpet went down. It was quite bad and I must have put in about 40 screws. I just went by the existing nail, went to the side a cm or two and popped in a screw. Very happy with the end result.


  • #5
    madds
    Registered Users, Registered Users 2 Posts: 1,884 ✭✭✭madds


    Calahonda52 wrote: »
    what makes you think they are there?

    Well there's a rad in each bedroom which is being fed by a pipe, so they're there somewhere. I'd rather take a cautious approach as against putting a screw through a pipe!

    Thanks for the replies lads on a Sunday evening.


  • #6
    madds
    Registered Users, Registered Users 2 Posts: 1,884 ✭✭✭madds


    theteal wrote: »
    I did this recently on the landing before new carpet went down. It was quite bad and I must have put in about 40 screws. I just went by the existing nail, went to the side a cm or two and popped in a screw. Very happy with the end result.

    Yes, that's the approach I was going to take also. Use a countersink bit first so the screw head sits just below the surface of the board.


  • Advertisement
  • #7
    looksee
    Registered Users, Registered Users 2 Posts: 28,767 ✭✭✭✭looksee


    Put the heating on, then feel the floor. (well it will find some of them!)


  • #8
    listermint
    Registered Users, Registered Users 2 Posts: 34,104 ✭✭✭✭listermint


    looksee wrote: »
    Put the heating on, then feel the floor. (well it will find some of them!)

    better of stripping down and lying face down on the floor.

    More coverage


  • #9
    LenWoods
    Registered Users, Registered Users 2 Posts: 617 ✭✭✭LenWoods


    looksee wrote: »
    Put the heating on, then feel the floor. (well it will find some of them!)

    Can imagine him rolling around the floor like he's tripping on acid and the wife walks in 😂😲😲😲


Advertisement