A&R Marketplace - Arcade and Retro 3D Printing Service

Also, in keeping with the open source nature of the model and 3D printing in general here's the modified file on Thingiverse(I've set it as a remix of the original)
I'll update it once Optimus confirms the chair fits, is to small or too big.

https://www.thingiverse.com/thing:3078517

Optimus Prime wrote: »

Looks great Steve! , do you want to send me those test ones so I can see if they are scale in it before you print them ? Or just fire away I don’t mind. They look good.

Also just on the thingverse link , these go in the Hold of the falcon not the cockpit.

I'll fix it up a little and do the proper print. If they dont fit I can do it again as it's a tiny amount of plastic that's needed. I actually fixed up a few bits for that deagostini model yesterday that people had posted as most were just not printable(bad models with errors etc). So with the other prints next to the chair and console I think its right(I printed some barrels and misc bits that go in the hold with the console thing).

I'll use the same stuff I used for Doges job, an ABS/Nylon mix that's pretty strong. I'll update the thingiverse file to reflect its for the hold, cheers for that.

Is it still called a Navigator chair?

Optimus Prime wrote: »

Cool , that’s great thanks a lot Steve ! It’s actually referred to as the Navigation Chair , it goes beside the navigation console in the hold. It’s the one han is sitting on in the A new hope when he is talking to Obi Wan while luke is using the ball thing for lightsaber training.

There are some other bits I’d like to get printed down the road too for it but so far I can’t find the files for download for free ��

I was looking to get some barrels /crates for t down the road as well.

Well you can have the barrels and crates I was using to test the scale.

This is the chair, yes?

These are the barrels and crates. Not sure if you can use them, but you might as well have them just in case.

3D printed Simon the Sorcerer lithophane. This one took a bit of work, but I'm happy with it. It's a gift for a big Simon fan.

CiDeRmAn wrote: »

Thanks for the wonderful one you made for me, as a present for She Who Must Be Obeyed.
You can post it up if you like, very nice indeed.

No problem, it turned out nice that one.

Glad some of it working out for ya

I'm moving most of my 3D printing stuff over to Gadunky.com at the moment, so if you need stuff done you can contact me via that as well as here.
I added my own take on 3D printed lithophanes(Blaze style) to the site recently and its taken off quite a bit, so i'll sort out other services through it as well rather than the old site you might have seen. Massive backlog at the moment due to one of my lithophanes ending up on the front page of imgur.com a week or two ago, so a lot of orders from that. Should be cleared up in a week if you need more done.

Few examples here:
https://www.gadunky.com/product-category/3dprint/lithophane/

Free Game Boy 3D printable lithophane for those with 3D printers.

https://www.gadunky.com/product/game_boy/

You can also grab it on Thingiverse along with my other free stuff.
https://www.thingiverse.com/RetromanIE/designs

CiDeRmAn wrote: »

Been a while since a request was made, and this isn't even A&R related... well not in it's entirety.

I would like to have a reset button for my Vectrex printed up,

Vectrex Reset Button



as well as a set (4) of leg extensions for my newly acquired 3DR Solo drone.

3DR Leg Extensions

I should stick up some more sample pics to liven up the thread maybe.

I'd say the reset button would be best done in resin(its a simple shape but I'm guessing you want it as perfect as possible). I could do the legs on a standard 3D printer, perhaps in PETG or ASA materials for strength.
Either way, no problem to do and wont be pricey(couple euro worth of material and postage on top).

For the resin I'd probably do a mix of 20% tough resin(Siraya Blu), 5% flex resin(Siraya tenacious) and the rest would be standard ABS like resin.

What colour do you want the button and legs?
Do you want a few sets of legs? As someone who also fly's drones, these leg extensions will break after a while, or after a 1 rough landing

A few sample prints. Not really retro related apart from the Metal Slug tank.
Nine tails was printed in clear resin and then hand painted with alcohol inks, the rest are from the printer with supports removed.

Gradius wrote: »

Obscure thing, but I'd definitely like to get a set of 4 cps1.5 screw caps, in grey to match the cover.

These are the little bits of plastic that sit in the screw holes.

Not a breeze where to get the designs though!

Have a look on Thingiverse or yeggi.com. Good bit of cps stuff around.

Gradius wrote: »

No joy, just a bit too obscure I suppose. Some interesting stuff though.

I'd say its only a very basic design that's needed. If you ever feel like it I'm sure you could design it in tinkercad(very basic user friendly 3d design web app).
https://www.tinkercad.com/

I mainly use fusion360 and some other more advanced tools, but still load up tinkercad if it's just something super quick and basic I need.

I designed this X Axis Pulley Idler in tinkercad a few years back. Took about 10 mins using drag and drop basic shapes and the design/3d print is still running on one of my laser cutters.