Advertisement
If you have a new account but are having problems posting or verifying your account, please email us on hello@boards.ie for help. Thanks :)
Hello all! Please ensure that you are posting a new thread or question in the appropriate forum. The Feedback forum is overwhelmed with questions that are having to be moved elsewhere. If you need help to verify your account contact hello@boards.ie

Pyronix DeltaBell Plus & HKC 10120

  • 09-12-2015 12:37PM
    #1
    KokaKola
    Registered Users, Registered Users 2 Posts: 13 ✭


    Help.

    Have just replaced an old HKC SABB with a Pyronix Grade 2/3 Delta Bell, and every time I close the lid the alarm goes off and I can't stop it from the control panel. Even with the lid closed and the tamper switch closed. The alarm panel is still reading EXt Bell Tamper switch open. If I manually press the tamper switch, it sets off the alarm. I have put a 4K7 resistor between tamper and SAB hold. Anyone have any tests I can do to see why tamper switch is reading open even when closed.

    Wiring is as follows:
    TR - T1
    STB -ve - STB
    Bell -ve - Bell
    Bell +ve - +12V
    SAB Hold - -12V

    4K7 Resistor between T2 and -12V.


Comments

  • #2
    KoolKid
    Moderators, Home & Garden Moderators, Technology & Internet Moderators Posts: 24,790 Mod ✭✭✭✭KoolKid


    Loop Sab hold to the top tamper. Wire tamper return into the other tamper with the resistor in series.


  • #3
    KokaKola
    Registered Users, Registered Users 2 Posts: 13 ✭KokaKola


    Perfect thanks for the response, works perfectly now.

    Also, do you happen to know if I put a Honeywell DT8012F5 PIR on its own zone to the same HKC panel does it need a EOL resistor?


  • #4
    KoolKid
    Moderators, Home & Garden Moderators, Technology & Internet Moderators Posts: 24,790 Mod ✭✭✭✭KoolKid


    You can do either. You programmed the EOL type you are using in Zone Hardware.


  • #5
    KokaKola
    Registered Users, Registered Users 2 Posts: 13 ✭KokaKola


    Thanks again Koolkid, this is a very useful form. Many thanks for all your help.


  • #6
    KokaKola
    Registered Users, Registered Users 2 Posts: 13 ✭KokaKola


    Okay everything working perfectly except PIR tamper. It is a single detector on a 6 wire cable. If I short the tamper pair at the detector connections, tamper alarm clears, but as soon as PIR is remounted Tamper Alarm appears. I have 2 new PIR's and have swapped them and fault still exists.

    So doesn't look like cabling, or detectors, more likely config of some sort? Any suggestions?


  • Advertisement
  • #7
    KoolKid
    Moderators, Home & Garden Moderators, Technology & Internet Moderators Posts: 24,790 Mod ✭✭✭✭KoolKid


    Can you put up a picture of the connections and what configuration of resistors are you using?


  • #8
    eddie_
    Registered Users, Registered Users 2 Posts: 60 ✭✭eddie_


    Hi would any one have a diagram on how to wire a delta us bell to a hkc panel. Many thanks in advance


  • #9
    altor
    Registered Users, Registered Users 2 Posts: 11,977 ✭✭✭✭altor


    eddie_ wrote: »
    Hi would any one have a diagram on how to wire a delta us bell to a hkc panel. Many thanks in advance

    Which HKC panel are you looking to wire it too?

    www.altor.ie



  • #10
    Tlfc85
    Registered Users, Registered Users 2 Posts: 2 ✭Tlfc85


    Hi would anyone have a drawing of the connection’s between a hkc 1070 and a pyronix deltabell,can’t get the bell to activate on alarm.
    Any help would be much appreciated .


  • #11
    Tlfc85
    Registered Users, Registered Users 2 Posts: 2 ✭Tlfc85


    Hi would anyone have a drawing of the connection’s between a hkc 1070 and a pyronix deltabell,can’t get the bell to activate on alarm.
    Any help would be much appreciated .


  • Advertisement
Advertisement