How To Fix Crack In Plastic Bath Tub

Gingko · 02-05-2012 10:50PM #1

Hi Folks! Small crack in plastic bath tub near tub hole. I've been quoted a ridiculous price to get it replaced so I'm just wondering if there was a way to repair it my self?

Been browsing the net and have found two ways, by epoxy and repair tape. Drill small 1/4 inch holes at either end of crack so it doesn't get bigger. Sand it down and clean off. Epoxy takes 12 hours before use while tape is only three. eHow website states that tape is more successful on cracks over 1 inch?

Anybody do this before? Was it a success? By the way plumber quoted me €650 to replace bath tub and side panels. Appreciate feedback. Thanks!

biko · 02-05-2012 10:58PM

Tape should work, and is easier. It'll show more though, if that's a factor?

fergal.b · 03-05-2012 07:02AM

If you can't find a bath repair kit you could use a marine gelcoat repair kit http://www.marineparts.ie/paint-and-maintenance/epoxy-repair-kits/plastic-padding-gelcoat-filler.html it comes in white "if your bath is white" just sand the crack so it becomes groove drill a hole each end and fill it with the gelcoat then scrape off the excess with an old credit card and when it's dry wet sand with 1000 -1500 grit wet paper and if you like polish out with rubbing compound.

Joey the lips · 03-05-2012 07:08AM

A repair near the waste plug is not verg successful. Its actually where most of the bath movement is.

I would replace the bath.

fergal.b · 03-05-2012 07:25AM

If money is tight and he can get to the crack from underneath he could sand the area and add a few layers of fiberglass cloth or mesh to reinforce it and make it stronger than it was in the first place,Total cost about €50 instead €650

Gingko · 03-05-2012 12:00PM

Thanks one and all for suggestions!

Gingko · 04-05-2012 03:59PM

Hey folks just to add I got a second quote from another guy for €320 supply and fit! Seems a great price! Less then half of other guy. What savings to be had when one shops around!

But before I give him the nod I think I'll try the sand, drill and repair tape method. Two small cracks both approx 1.5 inchs long. Only one letting out water. Some soft epoxy has been put on it for now.

CJhaughey · 04-05-2012 04:07PM

Would you not fit an steel enamel bath?
I think I paid 200 for the last one I bought
They never crack unlike the fibreglass ones.
The problem is where the waste exits the bath wall thickness is very thin, its the same in shower trays, this is the weak point in all fibreglass bathware.

Gingko · 04-05-2012 05:20PM

CJhaughey wrote: »

Would you not fit an steel enamel bath?
I think I paid 200 for the last one I bought
They never crack unlike the fibreglass ones.
The problem is where the waste exits the bath wall thickness is very thin, its the same in shower trays, this is the weak point in all fibreglass bathware.

Well put it this way. Last tub lasted just over ten years and I don't expect to have apartment for another ten! In fact maybe two or three years at the most although that could change?

So it's a case of keeping it maintained for the least amount of money possible during this time. I may still try sanding, drilling and taping first. Even if this holds for another year it would be well worth it! I have it letted out and one of the tenants is a big guy but very concious of property. He covered cracks with soft epoxy already to keep it sealed for a week or two.

Gingko · 04-05-2012 06:35PM

fergal.b wrote: »

If you can't find a bath repair kit you could use a marine gelcoat repair kit http://www.marineparts.ie/paint-and-maintenance/epoxy-repair-kits/plastic-padding-gelcoat-filler.html it comes in white "if your bath is white" just sand the crack so it becomes groove drill a hole each end and fill it with the gelcoat then scrape off the excess with an old credit card and when it's dry wet sand with 1000 -1500 grit wet paper and if you like polish out with rubbing compound.

Bath tub is plastic, is this not for fibreglass?

fergal.b · 04-05-2012 06:40PM

Gingko wrote: »

Bath tub is plastic, is this not for fibreglass?

It will work with plastic just make sure where your putting it is dry and roughed up with 400 paper to give it a bite.

Gingko · 04-05-2012 06:58PM

fergal.b wrote: »

It will work with plastic just make sure where your putting it is dry and roughed up with 400 paper to give it a bite.

Thanks fergal! You have experience of this? Will it work as it's at flexible end of tub so to speak? And would you recommend it more so then epoxy or tape?

fergal.b · 04-05-2012 07:50PM

Gingko wrote: »

Thanks fergal! You have experience of this? Will it work as it's at flexible end of tub so to speak? And would you recommend it more so then epoxy or tape?

I work a lot with epoxy and think you will get a much better finish with the paste than you will with the tape inside the bath, if you want to make it stronger you could put the tape or fiberglass mesh under the crack to stiffen it up if you do this you might get away with drilling holes and grinding out the crack just force it together with a little bit of resin you may still see the crack but it will be watertight and the fiberglass mesh will stop it from spreading.
http://www.ehow.com/how_4897957_repair-plastic-bathtub-cracked.html

How To Fix Crack In Plastic Bath Tub

Comments