Advertisement
If you have a new account but are having problems posting or verifying your account, please email us on hello@boards.ie for help. Thanks :)
Hello all! Please ensure that you are posting a new thread or question in the appropriate forum. The Feedback forum is overwhelmed with questions that are having to be moved elsewhere. If you need help to verify your account contact hello@boards.ie
Hi there,
There is an issue with role permissions that is being worked on at the moment.
If you are having trouble with access or permissions on regional forums please post here to get access: https://www.boards.ie/discussion/2058365403/you-do-not-have-permission-for-that#latest

Connecting flexible waste to basin

  • 25-02-2019 10:06pm
    #1
    Registered Users, Registered Users 2 Posts: 84 ✭✭


    Trying to connect a 1.25" threaded nut on the flexible waste pipe to the sink drain and it's leaking.
    Trouble is the nut on the end of the flexible pipe has movement in it, presumably to allow the nut to turn onto whatever.
    Am I missing a piece here?

    As you can see when it's connected it's leaking, if tighten it less to hand tight or get the wrench at it, same story.
    All pieces are brand new.

    Any ideas?

    Can see daylight in the nut beside the green washer:
    o7cLP.jpg

    The green washer meets the threaded sink drain almost perfectly, if I tighten too tight it feels like the flexible tube part is going up into the drain:
    vAZZF.jpg

    Drop of water, this is when it's fairly tight (didn't want to over do it, but it's more than hand tight)
    eXdhU.jpg

    Thanks for any help


Comments

  • Registered Users, Registered Users 2 Posts: 478 ✭✭rightjob!


    zzyxxx wrote: »
    Trying to connect a 1.25" threaded nut on the flexible waste pipe to the sink drain and it's leaking.
    Trouble is the nut on the end of the flexible pipe has movement in it, presumably to allow the nut to turn onto whatever.
    Am I missing a piece here?

    As you can see when it's connected it's leaking, if tighten it less to hand tight or get the wrench at it, same story.
    All pieces are brand new.

    Any ideas?

    Can see daylight in the nut beside the green washer:
    o7cLP.jpg

    The green washer meets the threaded sink drain almost perfectly, if I tighten too tight it feels like the flexible tube part is going up into the drain:
    vAZZF.jpg

    Drop of water, this is when it's fairly tight (didn't want to over do it, but it's more than hand tight)
    eXdhU.jpg

    Thanks for any help

    What is that waste going into,outside to a gully?
    The flexible waste has a flat flange surface and the sink grating is curved,you would be better off putting a trap on the sink and hard piping it then in wavin.
    Those flexible waste pipes are not great.


  • Registered Users, Registered Users 2 Posts: 84 ✭✭zzyxxx


    rightjob! wrote: »
    What is that waste going into,outside to a gully?
    The flexible waste has a flat flange surface and the sink grating is curved,you would be better off putting a trap on the sink and hard piping it then in wavin.
    Those flexible waste pipes are not great.

    There's a white PVC pipe coming out of the wall and I have the flexible pipe attached to that. Pictures didn't show up, will try attach again...
    I figure the Flexi pipe is easier as the drain is off centre to the waste pipe. With my limited knowledge I think this is easiest than multiple trips to woodies with trial and error approach


  • Registered Users, Registered Users 2 Posts: 84 ✭✭zzyxxx


    rightjob! wrote: »
    What is that waste going into,outside to a gully?
    The flexible waste has a flat flange surface and the sink grating is curved,you would be better off putting a trap on the sink and hard piping it then in wavin.
    Those flexible waste pipes are not great.

    There's a white PVC waste pipe coming out of the wall. Since it's off centre to the sink I thought the flexible pipe would be best. I wouldnt be confident that I'd get it all to line up without it to be honest.
    Will try attach pics again


  • Registered Users, Registered Users 2 Posts: 84 ✭✭zzyxxx


    zzyxxx wrote: »
    There's a white PVC waste pipe coming out of the wall. Since it's off centre to the sink I thought the flexible pipe would be best. I wouldnt be confident that I'd get it all to line up without it to be honest.
    Will try attach pics again

    Pics attached


  • Registered Users, Registered Users 2 Posts: 1,464 ✭✭✭monseiur


    Not an ideal solution to your problem........but if all else fails, dry thoroughly, apply a good bed of good quality silicon mastic, hand tighten well or use a wrench gently, leave for a few hours before using to allow the mastic to cure, that should do it !
    M.


  • Advertisement
  • Registered Users, Registered Users 2 Posts: 2,023 ✭✭✭whizbang


    Remove all the PTFE Tape. Its not for this job.


  • Registered Users, Registered Users 2 Posts: 1,114 ✭✭✭freddyuk


    Wrong fitting for the job. Don't tighten with a wrench!! Those ears give you sufficient leverage to tighten correctly so too much force distorts the joint and displaces the rubber gasket. Check the bottom of the sink waste and check it is smooth. The gasket has only a thin metal edge to seal onto. Gently screw the nut up hand tight only and then check for leaks. A quarter turn each time and check if leaks. If the gasket is already damaged you will need to replace.
    Best option is proper sink trap and pipe across and down onto drain.


  • Closed Accounts Posts: 208 ✭✭jhenno78


    You need to get rid of that thing completely and start again.

    The flexi itself is a cheap piece of crap and should never be used anywhere.
    You have no p-trap!
    Seeing as you haven't flagged this straight away, let's tell you...it's a big no-no.

    So yeah, you need to plumb the whole thing again. It's not an specially hard job so there's no reason to cut corners by using a flexi- anything.


  • Registered Users, Registered Users 2 Posts: 1,464 ✭✭✭monseiur


    jhenno78 wrote: »
    You need to get rid of that thing completely and start again.

    The flexi itself is a cheap piece of crap and should never be used anywhere.
    You have no p-trap!
    Seeing as you haven't flagged this straight away, let's tell you...it's a big no-no.

    So yeah, you need to plumb the whole thing again. It's not an specially hard job so there's no reason to cut corners by using a flexi- anything.

    I guess he could form a trap with the flexi pipe by going down straight first then up forming a U shape and then out to the gulley......not ideal but...
    M.


Advertisement