Advertisement
If you have a new account but are having problems posting or verifying your account, please email us on hello@boards.ie for help. Thanks :)
Hello all! Please ensure that you are posting a new thread or question in the appropriate forum. The Feedback forum is overwhelmed with questions that are having to be moved elsewhere. If you need help to verify your account contact hello@boards.ie
Hi there,
There is an issue with role permissions that is being worked on at the moment.
If you are having trouble with access or permissions on regional forums please post here to get access: https://www.boards.ie/discussion/2058365403/you-do-not-have-permission-for-that#latest

Cleaning the inside of a nut bin?

  • 13-12-2018 2:56pm
    #1
    Registered Users, Registered Users 2 Posts: 40


    Hi

    Getting mouldy nuts from the feed bin. Only got a load a couple of weeks ago into two separate bins & the newer one is fine. This particular nut bin is about 20 years old. Is it possible to clean the inside?

    Thanks :-)


Comments

  • Registered Users, Registered Users 2 Posts: 30,213 ✭✭✭✭whelan2


    What type of bin is it? I give it a few wallops from the outside with a fencing post


  • Registered Users, Registered Users 2 Posts: 12,044 ✭✭✭✭Say my name


    There's usually an inspection panel that you can unbolt off if you think you have a serious problem.


  • Registered Users, Registered Users 2 Posts: 786 ✭✭✭Cattlepen


    whelan2 wrote: »
    What type of bin is it? I give it a few wallops from the outside with a fencing post

    Had an auld ODwyer steel bin and this is what I use to do. Sometimes a few light taps of a sledge all around. Stay away from the mound dust. Not good for the bronchials


  • Registered Users, Registered Users 2 Posts: 40 Dot Cotton


    It's a spirofeed bin. If I go banging the sides will I only dislodge the mouldy nuts further? Am I best to wait until the current feed is gone & then work away?

    Thanks everyone for your replies


  • Registered Users, Registered Users 2 Posts: 18,996 ✭✭✭✭gozunda


    whelan2 wrote: »
    What type of bin is it? I give it a few wallops from the outside with a fencing post

    Wonderful picture - Whelan going demented at the nut bin with a large fencing post :pac:


  • Advertisement
  • Closed Accounts Posts: 20,633 ✭✭✭✭Buford T. Justice XIX


    Dot Cotton wrote: »
    It's a spirofeed bin. If I go banging the sides will I only dislodge the mouldy nuts further? Am I best to wait until the current feed is gone & then work away?

    Thanks everyone for your replies
    Yeah, wait till it's empty and give it a few gentle belts with a piece of timber to dislodge anything stuck around the inside, bag it up and keep it till you're spreading slurry later in the year and fire into the tanks when agitating.


  • Registered Users, Registered Users 2 Posts: 4,310 ✭✭✭Pkiernan


    What ever you do, Do not open this thread in the After Hours forum!


  • Registered Users, Registered Users 2 Posts: 1,577 ✭✭✭Bonzo Delaney


    Pkiernan wrote: »
    What ever you do, Do not open this thread in the After Hours forum!

    Or worse the sex and sexaulity fourm not that i do be on it just heard about it from a friend


  • Registered Users, Registered Users 2 Posts: 3,194 ✭✭✭foxy farmer


    Or worse the sex and sexaulity fourm not that i do be on it just heard about it from a friend

    The what now?


  • Registered Users, Registered Users 2 Posts: 7,748 ✭✭✭ganmo


    Or worse the sex and sexaulity fourm not that i do be on it just heard about it from a friend

    Not bulocks anyway :p


  • Advertisement
  • Registered Users, Registered Users 2 Posts: 30,213 ✭✭✭✭whelan2


    gozunda wrote: »
    Wonderful picture - Whelan going demented at the nut bin with a large fencing post :pac:

    Taking out all my frustrations on the poor meal bin


  • Registered Users, Registered Users 2 Posts: 278 ✭✭wing52


    Confined space entry!!!!

    Be careful. Nasty gases can build up.

    Don't go in side on your own.


  • Registered Users, Registered Users 2 Posts: 1,742 ✭✭✭lalababa


    There is a hatch in my bin where you can gain access to clean it out. But I don't go in 'coz I have a phobia of large spaces 'coz me bin is v. big 'coz me nuts are that big like.


  • Registered Users, Registered Users 2 Posts: 30,213 ✭✭✭✭whelan2


    lalababa wrote: »
    There is a hatch in my bin where you can gain access to clean it out. But I don't go in 'coz I have a phobia of large spaces 'coz me bin is v. big 'coz me nuts are that big like.
    I have no nuts so I might go in


  • Registered Users, Registered Users 2 Posts: 19,581 ✭✭✭✭Bass Reeves


    Wait until it is empty. Then get a rubber mallet and a ladder and wallop the ****e out of it. You may need sewer rods to clean out the chute part of it. Then get a load of nuts blown into it. Repeat during the summer if possible

    Slava Ukrainii



  • Registered Users, Registered Users 2 Posts: 7,920 ✭✭✭freedominacup


    Pig farm near me has an offset bearing attached to each bin that vibrates bin whenever auger is engaged. Stops any build up occurring.


  • Registered Users, Registered Users 2 Posts: 483 ✭✭pms7


    Have a 3 year old Spirofeed, use coarse ration, there is some sticking to the sides. Have patch of rust on the cone about 3'' across. Presume ration stuck inside causing it, but was shocked to see rust on the galvanise of a newish bin. Must obviously clean it out, but what to do with rust??


  • Registered Users, Registered Users 2 Posts: 30,213 ✭✭✭✭whelan2


    pms7 wrote: »
    Have a 3 year old Spirofeed, use coarse ration, there is some sticking to the sides. Have patch of rust on the cone about 3'' across. Presume ration stuck inside causing it, but was shocked to see rust on the galvanise of a newish bin. Must obviously clean it out, but what to do with rust??

    Go back to manufacturers, it shouldn't rust after such a short space of time


  • Registered Users, Registered Users 2 Posts: 40 Dot Cotton


    Thanks everyone 😊


  • Registered Users, Registered Users 2 Posts: 11,174 ✭✭✭✭Muckit


    Don't have a bin but l reckon the mild damp weather prob not helping things.


  • Advertisement
  • Registered Users, Registered Users 2 Posts: 3,108 ✭✭✭cute geoge


    could rain be getting in ?


  • Registered Users, Registered Users 2 Posts: 5,193 ✭✭✭alps


    The very hot weather and intense sunshine on bins caused sweating and moulding in many instances, some where this mild caused antibiotic problems in milk.

    The question of course is why were the rations sweating so much? Hmmmm...


  • Registered Users, Registered Users 2 Posts: 6,225 ✭✭✭charolais0153


    alps wrote: »
    The very hot weather and intense sunshine on bins caused sweating and moulding in many instances, some where this mild caused antibiotic problems in milk.

    The question of course is why were the rations sweating so much? Hmmmm...

    When you cut barley or whatever you have to turn it every day for a forrnightso it doesnt heat. I suppose in the summer barley was cut from field and straight into some lads bin and it started to heat. It was moved by the merchant for only a few days and it started to hear when it settled in the bin


  • Registered Users, Registered Users 2 Posts: 1,847 ✭✭✭Brown Podzol


    alps wrote: »
    The very hot weather and intense sunshine on bins caused sweating and moulding in many instances, some where this mild caused antibiotic problems in milk.

    The question of course is why were the rations sweating so much? Hmmmm...

    A dry matter analysis could answer that question for you. Propcorn treated grain, molasses and a dash of H2O to speed up the processing of hard grains and a lot of feed could be a lot wetter than you think. A lot of profit in selling water for €300 a ton.


Advertisement