Advertisement
If you have a new account but are having problems posting or verifying your account, please email us on hello@boards.ie for help. Thanks :)
Hello all! Please ensure that you are posting a new thread or question in the appropriate forum. The Feedback forum is overwhelmed with questions that are having to be moved elsewhere. If you need help to verify your account contact hello@boards.ie
Hi there,
There is an issue with role permissions that is being worked on at the moment.
If you are having trouble with access or permissions on regional forums please post here to get access: https://www.boards.ie/discussion/2058365403/you-do-not-have-permission-for-that#latest

Windows & Doors - foam trim left exposed

  • 22-10-2018 2:30pm
    #1
    Registered Users, Registered Users 2 Posts: 8


    Just had new windows and doors fitted to my house. The finish is unusual in that there is a foam / sponge trim on the exterior between the windows / doors and the masonry. I've never seen this before and am concerned it will rot over the years. Would be grateful for the views of anyone with a bit of knowledge, can post photos if that helps. Thanks.


Comments

  • Registered Users, Registered Users 2 Posts: 5,893 ✭✭✭Bullocks


    djm1234 wrote: »
    Just had new windows and doors fitted to my house. The finish is unusual in that there is a foam / sponge trim on the exterior between the windows / doors and the masonry. I've never seen this before and am concerned it will rot over the years. Would be grateful for the views of anyone with a bit of knowledge, can post photos if that helps. Thanks.

    It's usually used when fitting to seal up the frame to the ope. When the reveals are plastered it should all be covered and never seen again.
    You could put up a picture in case it's different from what I think but I'd say that's it


  • Registered Users, Registered Users 2 Posts: 8 djm1234


    Bullocks wrote: »
    It's usually used when fitting to seal up the frame to the ope. When the reveals are plastered it should all be covered and never seen again.
    You could put up a picture in case it's different from what I think but I'd say that's it

    Thanks very much, having trouble getting a photo up...is the fitter normally responsible for plastering over it?


  • Registered Users, Registered Users 2 Posts: 692 ✭✭✭jmBuildExt


    djm1234 wrote: »
    Thanks very much, having trouble getting a photo up...is the fitter normally responsible for plastering over it?

    Very often, not.
    Depends what you agreed


  • Registered Users, Registered Users 2 Posts: 8 djm1234


    jmBuildExt wrote: »
    Very often, not.
    Depends what you agreed

    Not what I hoped to hear but thanks for the info. Just agreed that they'd supply & fit! If they're not under obligation who is the best type of tradesman to do it?


  • Registered Users, Registered Users 2 Posts: 692 ✭✭✭jmBuildExt


    If this work was included, they would have used a line something like "make good the reveals".
    A plasterer is what you want.


  • Advertisement
  • Registered Users, Registered Users 2 Posts: 1,486 ✭✭✭Doop


    Very unusual for it not to be part of the deal.


  • Registered Users, Registered Users 2 Posts: 5,893 ✭✭✭Bullocks


    Is this replacing old windows? I thought it was a new build.
    Usually when replacing windows the plaster is knocked off inside and patched inside. The outside is not touched except for a bead of silicon to seal it back onto the old reveal.
    It's not always done this way. How big is the gap between frame and outside reveal? You might have to trim back a bit of foam to see that.


  • Registered Users, Registered Users 2 Posts: 8 djm1234


    Its replacing old windows, there was no written agreement as such. I'll try & get a couple of photos up shortly. Thanks guys.


  • Registered Users, Registered Users 2 Posts: 692 ✭✭✭jmBuildExt


    Just re-read the OP again myself....Didnt realise you were talking about the external reveals.
    Agree with above: it is unusual that the replacement would not be tight with outside reveals and then a line of mastic/silicon around the edges.

    A pic will be necessary i think.


  • Registered Users, Registered Users 2 Posts: 8 djm1234


    Hi,

    Can't post pics as I'm a new user but have broken the link in two which might work...

    https://imgur.com/TVu68lc

    Anyway, I'd also emailed the window fitter (50% of fees still outstanding) & they eventually replied stating "The black tape that you can on the outside is an energy sealing system must be left exposed".
    Putting this in writing gives me some confidence but any opinions very welcome.


  • Advertisement
  • Registered Users, Registered Users 2 Posts: 692 ✭✭✭jmBuildExt


    djm1234 wrote: »
    Hi,

    Can't post pics as I'm a new user but have broken the link in two which might work...

    https: //imgur.com/TVu68lc

    Anyway, I'd also emailed the window fitter (50% of fees still outstanding) & they eventually replied stating "The black tape that you can on the outside is an energy sealing system must be left exposed".
    Putting this in writing gives me some confidence but any opinions very welcome.

    The link didn't work - Sounds like they are talking about airtight tape.... Ive never heard of it being left exposed.


  • Moderators, Home & Garden Moderators Posts: 10,146 Mod ✭✭✭✭BryanF


    Just Push in the foam backing and silicone the window to wall.


  • Registered Users, Registered Users 2 Posts: 8 djm1234


    Hi, Here is another attempt to upload a pic, thanks again for your opinions.

    https://imgur.com/TVu68lc
    window trim.jpg


  • Registered Users, Registered Users 2 Posts: 5,893 ✭✭✭Bullocks


    djm1234 wrote: »
    Hi, Here is another attempt to upload a pic, thanks again for your opinions.

    https://imgur.com/TVu68lc
    window trim.jpg

    I haven't seen that stuff before but maybe the rep is right and that's the finish. It would look better in white or with white silicon over it though


  • Moderators, Home & Garden Moderators Posts: 10,146 Mod ✭✭✭✭BryanF


    Bullocks wrote: »
    I haven't seen that stuff before but maybe the rep is right and that's the finish. It would look better in white or with white silicon over it though

    It’s not the finish it’s the polyethylene foam backing rod, it should be finished with a mastic joint.


Advertisement