Advertisement
If you have a new account but are having problems posting or verifying your account, please email us on hello@boards.ie for help. Thanks :)
Hello all! Please ensure that you are posting a new thread or question in the appropriate forum. The Feedback forum is overwhelmed with questions that are having to be moved elsewhere. If you need help to verify your account contact hello@boards.ie
Please note that it is not permitted to have referral links posted in your signature. Keep these links contained in the appropriate forum. Thank you.

https://www.boards.ie/discussion/2055940817/signature-rules
Hi there,
There is an issue with role permissions that is being worked on at the moment.
If you are having trouble with access or permissions on regional forums please post here to get access: https://www.boards.ie/discussion/2058365403/you-do-not-have-permission-for-that#latest

2010 Avensis EPB issue!

  • 31-07-2017 8:15pm
    #1
    FinishingTime
    Registered Users, Registered Users 2 Posts: 11 ✭


    Hello All looking for bit of help.... Just replaced rear brake caliper on 2010 Avensis now getting EPB (electric parking brake) errors.... Error code P3653 "Refer to vehicle service manual".... when I put on handbrake get message on clock telling me to release handbrake, after handbrake released will not work again unless ignition switched off... will work again when ignition turned on with same situation... Looking at Toyota-Tec Eu's website can see no codes starting "P" under EPB (all EPB error codes seem to start with "C")..... any ideas?.....


Comments

  • #2
    Autochange
    Banned (with Prison Access) Posts: 1,648 ✭✭✭Autochange


    FinishingTime wrote: »
    Hello All looking for bit of help.... Just replaced rear brake caliper on 2010 Avensis now getting EPB (electric parking brake) errors.... Error code P3653 "Refer to vehicle service manual".... when I put on handbrake get message on clock telling me to release handbrake, after handbrake released will not work again unless ignition switched off... will work again when ignition turned on with same situation... Looking at Toyota-Tec Eu's website can see no codes starting "P" under EPB (all EPB error codes seem to start with "C")..... any ideas?.....

    Possibly needs to be programmed to show new brake piston position?


  • #3
    colm_mcm
    Registered Users, Registered Users 2 Posts: 73,520 ✭✭✭✭colm_mcm


    You need to hold the handbrake button with the ignition on for 5 seconds to reset it. Not sure if you push or pull the switch for 5 seconds.


  • #4
    FinishingTime
    Registered Users, Registered Users 2 Posts: 11 ✭FinishingTime


    Thanks Autochange something to put me in right direction... will search "Toyota-Tec later


  • #5
    Autochange
    Banned (with Prison Access) Posts: 1,648 ✭✭✭Autochange


    FinishingTime wrote: »
    Thanks Autochange something to put me in right direction... will search "Toyota-Tec later

    No worries, Com mcm may have the correct procedure for you


  • #6
    FinishingTime
    Registered Users, Registered Users 2 Posts: 11 ✭FinishingTime


    Tried that colm & no joy!... (Pushing for 5 seconds)


  • Advertisement
  • #7
    colm_mcm
    Registered Users, Registered Users 2 Posts: 73,520 ✭✭✭✭colm_mcm


    Try pulling instead?

    Ignition on, engine off.



    Or else I'm doting,


  • #8
    FinishingTime
    Registered Users, Registered Users 2 Posts: 11 ✭FinishingTime


    Will do... Thanks


  • #9
    Autochange
    Banned (with Prison Access) Posts: 1,648 ✭✭✭Autochange


    Im convinced it needs to be reset via a scanner of toyota diagnostic tool. Electric handbrakes work to fine tolerances and throw on the light if the system reads any discrepancies.


  • #10
    FinishingTime
    Registered Users, Registered Users 2 Posts: 11 ✭FinishingTime


    Yes Autochange might be beyond me but if could identify error code P3653 might help... & colm Toyota say to cancel full release mode "A" Turn ignition ON "B" Press & hold the EPB for five seconds to cancel full release mode... will search more tomorrow...


  • #11
    Autochange
    Banned (with Prison Access) Posts: 1,648 ✭✭✭Autochange


    Have you tried to erase the code then try operate the handbrake with just the ignition on? may be an unrelated code


  • Advertisement
Advertisement