Advertisement
If you have a new account but are having problems posting or verifying your account, please email us on hello@boards.ie for help. Thanks :)
Hello all! Please ensure that you are posting a new thread or question in the appropriate forum. The Feedback forum is overwhelmed with questions that are having to be moved elsewhere. If you need help to verify your account contact hello@boards.ie
Hi there,
There is an issue with role permissions that is being worked on at the moment.
If you are having trouble with access or permissions on regional forums please post here to get access: https://www.boards.ie/discussion/2058365403/you-do-not-have-permission-for-that#latest

remove cooker screw

  • 15-06-2017 10:02pm
    #1
    Registered Users, Registered Users 2 Posts: 2,063 ✭✭✭


    IMG_20170615_223009485.jpgAny idea how I can remove this screw from a stanley twin. it seems to be stuck solid. I have sprayed it with penetrating oil to little avail.


Comments

  • Registered Users, Registered Users 2 Posts: 2,056 ✭✭✭wait4me


    Have you tried to tighten it first? That often breaks the seal faster - worth a try


  • Registered Users, Registered Users 2 Posts: 455 ✭✭mcgragger


    you should try a long shaft screw driver - the bigger the better for torque.

    Also - what did you spray with WD?


  • Registered Users, Registered Users 2 Posts: 12,870 ✭✭✭✭Dtp1979


    Try a blow torch. Other than that you'll have to drill it out


  • Registered Users, Registered Users 2 Posts: 4,325 ✭✭✭iLikeWaffles


    Electric screw driver! Set the torque on the lowest setting and gradually increase. The knocking from the barrel should be enough to vibrate it loose the increase in torque should get it out. Is it a lefty or a righty?


  • Registered Users, Registered Users 2 Posts: 12,870 ✭✭✭✭Dtp1979


    Electric screw driver! Set the torque on the lowest setting and gradually increase. The knocking from the barrel should be enough to vibrate it loose the increase in torque should get it out. Is it a lefty or a righty?

    That doesn't work on cookers. There soooo hard to open. I nearly alway drill them out


  • Advertisement
  • Registered Users, Registered Users 2 Posts: 488 ✭✭The Diddakoi


    Do you have an impact driver ??
    That worked on my stove.


  • Registered Users, Registered Users 2 Posts: 2,063 ✭✭✭UrbanFret


    mcgragger wrote: »
    you should try a long shaft screw driver - the bigger the better for torque.

    Also - what did you spray with WD?
    yeah wd40


  • Registered Users, Registered Users 2 Posts: 2,063 ✭✭✭UrbanFret


    alf66 wrote: »
    Do you have an impact driver ??
    That worked on my stove.
    No I dont have one. might be worth a try.


  • Registered Users, Registered Users 2 Posts: 2,063 ✭✭✭UrbanFret


    wait4me wrote: »
    Have you tried to tighten it first? That often breaks the seal faster - worth a try
    No I haven't tried that yet.


  • Registered Users, Registered Users 2 Posts: 2,063 ✭✭✭UrbanFret


    I have access to a really good cordless impact driver. Is there such a thing as a socket with a screw type end on it?


  • Advertisement
  • Registered Users, Registered Users 2 Posts: 2,063 ✭✭✭UrbanFret


    Electric screw driver! Set the torque on the lowest setting and gradually increase. The knocking from the barrel should be enough to vibrate it loose the increase in torque should get it out. Is it a lefty or a righty?

    I presumed it was a right hand thread. It's not inclined to go either way for me.


  • Registered Users, Registered Users 2 Posts: 90 ✭✭TalkingBull


    if your sure its stuck, you could lift off the other plate on the left and reach in under with a vice grips and try turn that screw from under the cover, try not tighten vicegrips too much and damage the threads. But try a big heavy sreewdriver option first. a nice dirty job, good luck!!


  • Registered Users, Registered Users 2 Posts: 2,063 ✭✭✭UrbanFret


    if your sure its stuck, you could lift off the other plate on the left and reach in under with a vice grips and try turn that screw from under the cover, try not tighten vicegrips too much and damage the threads. But try a big heavy sreewdriver option first. a nice dirty job, good luck!!

    I think The screw on the other plate would be even harder to shift.;)


  • Registered Users, Registered Users 2 Posts: 72 ✭✭c ashelmore


    Looked everywhere to get a big enough screwdriver for these.In the end I made my own:get a 1inch or so wood drill bit .cut off point with a grinder, then use it in an impact drill.Never fails(yet)


  • Registered Users, Registered Users 2 Posts: 2,063 ✭✭✭UrbanFret


    Looked everywhere to get a big enough screwdriver for these.In the end I made my own:get a 1inch or so wood drill bit .cut off point with a grinder, then use it in an impact drill.Never fails(yet)
    might give this a shot.;)


  • Closed Accounts Posts: 9,764 ✭✭✭my3cents


    Looked everywhere to get a big enough screwdriver for these.In the end I made my own:get a 1inch or so wood drill bit .cut off point with a grinder, then use it in an impact drill.Never fails(yet)

    Worked for me :D

    Thanks for that, for the OP if he's not done this yet then a 20 mm FLAT wood with the point half ground off (the remaining bit helps center the tool) and ground down on the sides worked perfectly.

    I didn't need an impact drill instead just turned the flat part of the bit close to the screw in a adjustable spanner. Had left the nuts soaking for a while in Transyl which really is miles better than WD40.

    Now to find a part number for a replacement for the one that was already cracked - thanks Waterford Stanley your donkey's year's old parts list don't include that part :rolleyes:

    Edit> sorry OP I thought you were removing the stay bar screws (the ones in the corners of the stove under little silver cover plates) so you'll probably need a 16mm spade bit and will have to grind the point all the way off.


Advertisement