Dboys AK Parts.

LeeHarvey

As title states. Looking for some parts from a DBoys AK like outer barrel, top cover and mechanism, hop chamber and other bits n' bobs you may have.

DeBurca

What length outer barrel ????????????????????????

Can you supply a be more info regarding "other bits n' bobs you may have"

LeeHarvey

Putting together a custom build off a Matrix receiver I have ages, not sure on outer barrel length, may have to cut and join a longer barrel to a custom length.
As regards other parts, - selector lever and related assembly, top cover lock mechanism and button, rear sight, fixed polymer butt, and any other internal parts I haven't mentioned.

DeBurca

LeeHarvey wrote: »

Putting together a custom build off a Matrix receiver I have ages, not sure on outer barrel length, may have to cut and join a longer barrel to a custom length.
As regards other parts, - selector lever and related assembly, top cover lock mechanism and button, rear sight, fixed polymer butt, and any other internal parts I haven't mentioned.

I have a short bare barrel is it for a TM or VFC style front end ????????????????

I differently have a stock with butt plate and I might have two of them. I also should have a selector lever and related bits
Do you need a V3 gearbox shell ??????????????????????

Let me check on the above and get back to you tomorrow

LeeHarvey

Not sure what front end I have, the receiver is Matrix and is compatible with DBoys and LCT parts so I am sticking with DBoys parts and DBoys compatible parts to build off as they are cheap and there is a great selection available.
Also - as regards any internals, I have a complete custom V3 gearbox and motor assembled so am ok in that department.
I just need the "bones" of the gun in terms of smaller sub assemblies and the parts listed above.

DeBurca

Would these parts suit you ????????????????

Selector parts


Rear sight

LeeHarvey

Rear sight is good, is that all the parts I need for the selector?

DeBurca

LeeHarvey wrote: »

Rear sight is good, is that all the parts I need for the selector?

Yes assuming that the selector plate is fitted to the gearbox

LeeHarvey

Nothing fitted to the side of the gearbox, just the in-built recess for the related selector assembly.

DeBurca

LeeHarvey wrote: »

Nothing fitted to the side of the gearbox, just the in-built recess for the related selector assembly.

No nothing extra needed to work the selectors

LeeHarvey

OK, dollar value required for these in the post to me?

DeBurca

Are you still looking for a stock, got anything to trade ?????????????????????

LeeHarvey

Can you post a pic of the buttstock? Must be a plastic/polymer fixed type.
I have shed loads of stuff, mostly stock motors, gears, pistons, and inner barrels etc. Mostly brand new. Any interest in those?
I can dig about and post a picture of what I have if you like?

LeeHarvey

Two tan forward grips, a G36C quad rail fore end, three G36C top rails/sights, a set a brand new in the bag 6mm bearings, and a triple mag pouch by "8 Fields"
Note - the G36C top rail/sights at the top is real-steel, it is a very solid piece of kit, the airsoft versions don't hold a candle to its quality.

DeBurca

Would this stock suit you ??????????????????????

LeeHarvey

Need to see the interface/screw holes. Was it sanded?

DeBurca

The stock was covered in a rubber type material which became very sticky so it was removed and the stock sanded smooth
Below are photos of the Top and Bottom of the stock where it connects to the body

Top of stock


Bottom of stock

LeeHarvey

Stock won't match my receiver. I'll take the other parts though if you can see a trade you like or attach a € value to them.

G308

Have a whole d boys ak74 mn the solid folding stock version with a zenith ris handguard works fine just needs a battery it's wired to deans €150 for the lot FPS last checked was 320

LeeHarvey

Seen it! Beautiful rifle, but already have one - with a GP25 mounted to it. Thanks for the offer though.

DeBurca

Pity about the stock but if you are happy I will trade the other parts as shown in the photos for the G36 fore end

I also have some other Brand new AK that may interest you
A Brand new unopened AK Pistol grip and a Brand new handguard rail with 20mm top rail it replace the standard top hand guard for something a little different

Pistol grip


Handguard rail

LeeHarvey

Excellent. I'll take all except the butt stock so. Anything else from the pic you want?

DeBurca

Sorry no all I want is the G36 rail for the selector parts and front sight
I would sell the Pistol grip and handguard rail for €25

LeeHarvey

Fair enough, can you give me a price/trade for all except the pistol grip and stock?

DeBurca

LeeHarvey wrote: »

Fair enough, can you give me a price/trade for all except the pistol grip and stock?

Trade my selector parts and front sight - for your G36 handguard
I would sell the handguard rail for €20 its new still in the box
You pay for postage of the G36 rail to me, I pay for sending my stuff to you

LeeHarvey

Perfect, to PM's?

DeBurca

LeeHarvey wrote: »

Perfect, to PM's?

Grand send me a PM