Advertisement
If you have a new account but are having problems posting or verifying your account, please email us on hello@boards.ie for help. Thanks :)
Hello all! Please ensure that you are posting a new thread or question in the appropriate forum. The Feedback forum is overwhelmed with questions that are having to be moved elsewhere. If you need help to verify your account contact hello@boards.ie
Hi there,
There is an issue with role permissions that is being worked on at the moment.
If you are having trouble with access or permissions on regional forums please post here to get access: https://www.boards.ie/discussion/2058365403/you-do-not-have-permission-for-that#latest

install shower door on uneven shower tray

  • 13-05-2016 6:33pm
    #1
    Moderators, Business & Finance Moderators, Science, Health & Environment Moderators, Society & Culture Moderators Posts: 51,690 Mod ✭✭✭✭


    Hi

    Wondering if anyone can suggest what to do here. I'm hoping to replace a shower curtain with a shower door but the tray upon which it will rest is not level from halfway across 450mm it is lower gradually lowering to approx half an inch at the wall.

    Is there foam or filler I could use to plug the gap?

    Any suggestions appreciated thanks :)


Comments

  • Registered Users, Registered Users 2 Posts: 2,056 ✭✭✭wait4me


    A pic can "tell a thousand words" and might help us help you.....


  • Registered Users, Registered Users 2 Posts: 2,092 ✭✭✭Gen.Zhukov


    If I'm reading the problem right....

    Use the seal on the bottom of the door to take up the difference. It would depend on the seal and how much it fits onto the glass.

    Hopefully what you would end up with is, the working part of the seal stays true to the tray but would be slightly off square with the door if ya get my drift.

    Maybe someone else more in know would advise on what to hold the seal on the door with.


  • Moderators, Business & Finance Moderators, Science, Health & Environment Moderators, Society & Culture Moderators Posts: 51,690 Mod ✭✭✭✭Stheno


    1.618 wrote: »
    If I'm reading the problem right....

    Use the seal on the bottom of the door to take up the difference. It would depend on the seal and how much it fits onto the glass.

    Hopefully what you would end up with is, the working part of the seal stays true to the tray but would be slightly off square with the door if ya get my drift.

    Maybe someone else more in know would advise on what to hold the seal on the door with.

    The seal on the bottom of the door is no help as it's fi e for half the space but when we tried to fit the door it wouldn't close due to the lack of the tray being level. We can adjust it so the door will open and close but now half this half inch gap
    I can't get a pic at the moment


  • Registered Users, Registered Users 2 Posts: 73,520 ✭✭✭✭colm_mcm


    is there a frame around the door that attaches to or sits on the shower tray?


  • Closed Accounts Posts: 1,847 ✭✭✭Armchair Andy


    dural_duracove_aluminium_silver.jpg

    Could you set the door level and use a packer something like above to hide the gap? Seal it off with a silicone or similar sealant.


  • Advertisement
  • Registered Users, Registered Users 2 Posts: 2,092 ✭✭✭Gen.Zhukov


    Stheno wrote: »
    The seal on the bottom of the door is no help as it's fi e for half the space but when we tried to fit the door it wouldn't close due to the lack of the tray being level. We can adjust it so the door will open and close but now half this half inch gap
    I can't get a pic at the moment

    Again if I understand...

    If you were to raise the whole door up (on its wall fitting) to a position where the seal is good for the half of the door furtherest from the hinge you would be left with tapered gap leading back to the hinge and it would have the largest gap at the wall ?

    If that is the case, do that and then drop the seal down to fill the gap so the seal is flush with the tray.


  • Moderators, Business & Finance Moderators, Science, Health & Environment Moderators, Society & Culture Moderators Posts: 51,690 Mod ✭✭✭✭Stheno


    colm_mcm wrote: »
    is there a frame around the door that attaches to or sits on the shower tray?

    No the frame only attaches to the wall. The shower has three Walsh then the space for the door. When you put in the panels the door slots into that is when you get the gap trying to make sure the door will open and close. It slides I in to the panels but won't close due to the uneveness and the door has to be adjusted on one side so it closes which leaves the gap


  • Moderators, Business & Finance Moderators, Science, Health & Environment Moderators, Society & Culture Moderators Posts: 51,690 Mod ✭✭✭✭Stheno


    dural_duracove_aluminium_silver.jpg

    Could you set the door level and use a packer something like above to hide the gap? Seal it off with a silicone or similar sealant.

    This is what I need, where would I get that?


  • Moderators, Business & Finance Moderators, Science, Health & Environment Moderators, Society & Culture Moderators Posts: 51,690 Mod ✭✭✭✭Stheno


    1.618 wrote: »
    Again if I understand...

    If you were to raise the whole door up (on its wall fitting) to a position where the seal is good for the half of the door furtherest from the hinge you would be left with tapered gap leading back to the hinge and it would have the largest gap at the wall ?

    If that is the case, do that and then drop the seal down to fill the gap so the seal is flush with the tray.

    No the hinged side of the door is flush, it's the opening part where the gap is


  • Registered Users, Registered Users 2 Posts: 2,092 ✭✭✭Gen.Zhukov


    Stheno wrote: »
    No the hinged side of the door is flush, it's the opening part where the gap is

    Ok. Without seeing it 1st hand it's hard to judge the solution. I still think adjusting the hight of the door and the seal on the door is the way to go even if it means a new and diff type of seal.


  • Advertisement
  • Registered Users, Registered Users 2 Posts: 73,520 ✭✭✭✭colm_mcm


    The door would have to be plumb anyway, so the only way I can see of solving this is by raising the door a bit and getting a piece of white Aluminium box section ripped down. Talk to a window and door supplier and they might oblige you.
    This sort of thing
    stockshape-squaretube.gif
    You could fix some brackets to the wall and attach the box section to these, and seal between that and the shower tray

    This sort of thing
    shower.jpg

    Obviously the right thing to do is make the tray level though.


  • Moderators, Business & Finance Moderators, Science, Health & Environment Moderators, Society & Culture Moderators Posts: 51,690 Mod ✭✭✭✭Stheno


    1.618 wrote: »
    Ok. Without seeing it 1st hand it's hard to judge the solution. I still think adjusting the hight of the door and the seal on the door is the way to go even if it means a new and diff type of seal.

    That's exactly it, I need a 450mm long seal that I can use to bridge the gap :)

    It's too big for silicone, so something like posted earlier would be perfect.


  • Closed Accounts Posts: 1,847 ✭✭✭Armchair Andy


    Stheno wrote: »
    This is what I need, where would I get that?

    I've only ever seen them as part of a complete shower door which wouldn't be worth buying for.
    I'm sure there's something similar to trim in timber floors to tiles, maybe a flooring warehouse.

    Any good steelworks should come up with a stainless steel solution if you approached them, just a question of meeting the right person.


Advertisement