Advertisement
If you have a new account but are having problems posting or verifying your account, please email us on hello@boards.ie for help. Thanks :)
Hello all! Please ensure that you are posting a new thread or question in the appropriate forum. The Feedback forum is overwhelmed with questions that are having to be moved elsewhere. If you need help to verify your account contact hello@boards.ie
Hi there,
There is an issue with role permissions that is being worked on at the moment.
If you are having trouble with access or permissions on regional forums please post here to get access: https://www.boards.ie/discussion/2058365403/you-do-not-have-permission-for-that#latest

HW/CH timer

  • 05-12-2015 4:12pm
    #1
    Registered Users, Registered Users 2 Posts: 3,591 ✭✭✭


    Hi folks,

    I'm hoping to get some advice on the current hot water/central heating set-up in our apartment. Appreciate any comments/suggestions.

    We have a digital timer that is supposed to allow us to programme times for the CH and HW. There hasn't been a need to use the CH yet and unless this winter is drastically colder I don't imagine we will use it this year either. We do of course need and use hot water on a daily basis.

    I have programmed the digital timer to heat water in the morning. I recently noticed that we seemed to have a lot of hot water all the time so I re-programmed the timer to come on for only two ten minute periods in a week. However, we still have piping hot water all the time so I am definitely going wrong somewhere.

    I have attached two photos of the timer set-up and tank in the hopes that they may be of some help. Should the immersion switch be left on all the time or will the timer work if it is left off?

    Thanks in advance for your help!


Comments

  • Registered Users, Registered Users 2 Posts: 8,565 ✭✭✭K.Flyer


    That looks exactly like the set up in Island Key apartments.
    No, your immersion switch should be off, there is no need for it to be on if you are using the heating system.
    If you have the immersion switched off and the the time clock only running for ten minutes and you still have an abundance of hot water then most likely the problem is your motorised zone valve is not closing properly and is allowing the flow from the heating system to keep the cylinder hot all the time.


  • Registered Users, Registered Users 2 Posts: 1,884 ✭✭✭Robbie.G


    Tristram wrote: »
    Hi folks,

    I'm hoping to get some advice on the current hot water/central heating set-up in our apartment. Appreciate any comments/suggestions.

    We have a digital timer that is supposed to allow us to programme times for the CH and HW. There hasn't been a need to use the CH yet and unless this winter is drastically colder I don't imagine we will use it this year either. We do of course need and use hot water on a daily basis.

    I have programmed the digital timer to heat water in the morning. I recently noticed that we seemed to have a lot of hot water all the time so I re-programmed the timer to come on for only two ten minute periods in a week. However, we still have piping hot water all the time so I am definitely going wrong somewhere.

    I have attached two photos of the timer set-up and tank in the hopes that they may be of some help. Should the immersion switch be left on all the time or will the timer work if it is left off?

    Thanks in advance for your help!

    The immersion looks as if it's switched on 24/7 so it's heating constantly
    The timer should work
    Find with the immersion switch turned off


  • Registered Users, Registered Users 2 Posts: 3,591 ✭✭✭Tristram


    Robbie.G wrote: »
    The immersion looks as if it's switched on 24/7 so it's heating constantly
    The timer should work
    Find with the immersion switch turned off

    Thanks for this suggestion. The experiment is underway. I ran a bath for the OH to use all the hot water. If nothing else, brownie points for this! ;) I've set the timer to heat the water for 30 minutes and will test after.
    K.Flyer wrote: »
    That looks exactly like the set up in Island Key apartments.
    No, your immersion switch should be off, there is no need for it to be on if you are using the heating system.
    If you have the immersion switched off and the the time clock only running for ten minutes and you still have an abundance of hot water then most likely the problem is your motorised zone valve is not closing properly and is allowing the flow from the heating system to keep the cylinder hot all the time.

    Thanks for the comment. This is a bit over my head but I will come back to it should the above experiment fail.

    Thanks guys!


  • Registered Users, Registered Users 2 Posts: 3,591 ✭✭✭Tristram


    Thanks guys! You were correct. I've turned off the immersion switch and water heated using the timer function. I wonder how much of an impact this will make on the electricity bill given that the immersion had been on constantly.


Advertisement