Advertisement
If you have a new account but are having problems posting or verifying your account, please email us on hello@boards.ie for help. Thanks :)
Hello all! Please ensure that you are posting a new thread or question in the appropriate forum. The Feedback forum is overwhelmed with questions that are having to be moved elsewhere. If you need help to verify your account contact hello@boards.ie
Hi there,
There is an issue with role permissions that is being worked on at the moment.
If you are having trouble with access or permissions on regional forums please post here to get access: https://www.boards.ie/discussion/2058365403/you-do-not-have-permission-for-that#latest

skirting boards cut

  • 29-09-2014 12:56pm
    #1
    Registered Users, Registered Users 2 Posts: 4


    Hey guys, where can i get skirting boards cut to length with the proper angles and all? Im in dublin and iv tried homebase and b&q so far but no luck.
    Thanks


Comments

  • Registered Users, Registered Users 2 Posts: 268 ✭✭Ging Ging


    Go back to any hardware and purchase a measuring tape, a pencil, a mitre ( for angles) and a wood saw. The world of wood will then be your oyster.

    Alternatively you can hire a carpenter.


  • Closed Accounts Posts: 18,066 ✭✭✭✭Happyman42


    piglets wrote: »
    Hey guys, where can i get skirting boards cut to length with the proper angles and all? Im in dublin and iv tried homebase and b&q so far but no luck.
    Thanks

    Never seen that service offered anywhere. Unless you have a very accurately built house it would be difficult to do this offsite. A few mm out either way could be very annoying.


  • Registered Users, Registered Users 2 Posts: 605 ✭✭✭breghall


    you buy the skirting and cut it to size...... you don't buy it pre cut to your desired length and angle !


  • Registered Users, Registered Users 2 Posts: 2,386 ✭✭✭RebelButtMunch




  • Registered Users, Registered Users 2 Posts: 5,401 ✭✭✭DublinDilbert


    piglets wrote: »
    Hey guys, where can i get skirting boards cut to length with the proper angles and all? Im in dublin and iv tried homebase and b&q so far but no luck.
    Thanks

    Get a few off-cuts and play around, you'll soon get the hang of it. Loads of video's on you-tube to show you how too.

    There's two different methods for doing internal corners a 45 degree cut on each or you can cut one piece so it fits around the other.

    A hand saw is about €10 and a coping saw about the same. Definitely tools you should have around if your doing any work.

    It will take a little bit of practice but you can do it over and over till its right. Also with many internal corners are never seen once furniture goes in, so no big issue...


  • Advertisement
  • Registered Users, Registered Users 2 Posts: 23,688 ✭✭✭✭mickdw


    piglets wrote: »
    Hey guys, where can i get skirting boards cut to length with the proper angles and all? Im in dublin and iv tried homebase and b&q so far but no luck.
    Thanks

    They simply would never fit so no point trying to buy them like that.


  • Registered Users, Registered Users 2 Posts: 27,370 ✭✭✭✭GreeBo


    Rent a chop saw and practice.


  • Registered Users, Registered Users 2 Posts: 1,124 ✭✭✭jonon9


    I would throw in a sliding bevel just in case your corners are not squared.


  • Registered Users, Registered Users 2 Posts: 27,370 ✭✭✭✭GreeBo


    jonon9 wrote: »
    I would throw in a sliding bevel just in case your corners are not squared.

    Thats what caulk is for!:pac:

    Seriously, dealing with non-90* angles for a beginner will cause lots of wasted wood.


  • Registered Users, Registered Users 2 Posts: 2,683 ✭✭✭Carpenter


    Some practice will help


  • Advertisement
  • Closed Accounts Posts: 2,008 ✭✭✭scudo2


    GreeBo wrote: »
    Rent a chop saw and practice.

    Rent a carpenter and watch.


  • Registered Users, Registered Users 2 Posts: 27,370 ✭✭✭✭GreeBo


    scudo2 wrote: »
    Rent a carpenter and watch.

    Pretty sure a chop saw would be significantly cheaper than a carpenter tbh.

    Its not rocket science.


  • Registered Users, Registered Users 2 Posts: 2,376 ✭✭✭jack of all


    If this something you want to try for yourself you could do worse than spend €20- 30 on a hardpoint handsaw, coping saw and combi square. Have a look on youtube to see how it's done and as long as you have some suitable way of clamping the timber (B&D workmate is ideal) you could practice on some offcuts. It's not rocket science but if walls are off-square (the are seldom perfect), the floor is uneven or the wall finish uneven this is where experience comes into play. Either way the saws and square are handy to have.


  • Registered Users, Registered Users 2 Posts: 23,688 ✭✭✭✭mickdw


    GreeBo wrote: »
    Pretty sure a chop saw would be significantly cheaper than a carpenter tbh.

    Its not rocket science.

    Most people will make an absolute balls of them chopsaw or not.


Advertisement