Advertisement
If you have a new account but are having problems posting or verifying your account, please email us on hello@boards.ie for help. Thanks :)
Hello all! Please ensure that you are posting a new thread or question in the appropriate forum. The Feedback forum is overwhelmed with questions that are having to be moved elsewhere. If you need help to verify your account contact hello@boards.ie
Hi there,
There is an issue with role permissions that is being worked on at the moment.
If you are having trouble with access or permissions on regional forums please post here to get access: https://www.boards.ie/discussion/2058365403/you-do-not-have-permission-for-that#latest

How to go about solving this ?

  • 19-08-2014 11:46pm
    #1
    Registered Users, Registered Users 2 Posts: 19,717 ✭✭✭✭


    I'm currently collecting the matierals to construct a free standing floor lamp entirely out of copper piping. I'm gonna use this design here as I like the proportions, dimensions, look, etc

    http://www.homeportfolio.com/catalog/Product.jhtml?prodId=282401

    Rather than use wooden spools like they have this will be made entirely from copper piping and elbows.

    So I'm trying to figure out a way of accurately estimating the lengths of each individual piece of pipe before I begin cutting them up. The only thing I know thus far is that the lamp pictured above is 183cm tall and 48cm wide at it's widest point.

    So how to go about accurately determining all the individual lengths ? I thought of getting a ruler out on the PC screen and measuring in length and width in millimetres and finding out the scale from the computer page to a real life version. But would this work or does then the distance the photographer was from the lamp when shooting it also come into play to distort any perceived results ?

    And if I can just measure in mm to get a ratio of mm to cm how best to do it to get it reasonable accurate ? Would I better to print it on an a4 page and go from there, or even something bigger than a4 ?


Comments

  • Registered Users, Registered Users 2 Posts: 249 ✭✭Frigating


    What's the width of the copper piping/elbows?


  • Registered Users, Registered Users 2 Posts: 19,717 ✭✭✭✭Muahahaha


    It's one inch piping, 22 millimetres I think


  • Registered Users, Registered Users 2 Posts: 1,169 ✭✭✭dlouth15


    Muahahaha wrote: »
    So how to go about accurately determining all the individual lengths ? I thought of getting a ruler out on the PC screen and measuring in length and width in millimetres and finding out the scale from the computer page to a real life version. But would this work or does then the distance the photographer was from the lamp when shooting it also come into play to distort any perceived results ?
    Distance should not make much of a difference. The important thing is that the picture was taken head on to the lamp i.e. not at an angle. However I don't think it is advisable to copy exactly the original design if you are using a different material as the lamp may not balance properly due to the extra weight of the copper.
    And if I can just measure in mm to get a ratio of mm to cm how best to do it to get it reasonable accurate ? Would I better to print it on an a4 page and go from there, or even something bigger than a4 ?
    You could try opening up the image in a graphics editor. These allow you to pinpoint the pixel coordinates for any point on the image. Once you've worked out the pixel scale based on the height of the lamp it should be fairly easy to work out the dimensions of the other parts of the lamp, though as I've mentioned this may not be advisable for reasons of balance.


  • Registered Users, Registered Users 2 Posts: 249 ✭✭Frigating


    Dunno if you still need this or if you've figured it out, but I did this for you:

    s28.postimg.org/e5gxs93x9/lamp_1.png

    That doesn't accurately take into account the joints though. It depends how well the pipes fit into the elbows. I'm sure you can figure that bit out though. It should be pretty much accurate apart from that.


  • Registered Users, Registered Users 2 Posts: 19,717 ✭✭✭✭Muahahaha


    Frigating wrote: »
    Dunno if you still need this or if you've figured it out, but I did this for you:

    s28.postimg.org/e5gxs93x9/lamp_1.png

    That doesn't accurately take into account the joints though. It depends how well the pipes fit into the elbows. I'm sure you can figure that bit out though. It should be pretty much accurate apart from that.

    You absolute legend, I can't thank this post enough ! I think you've saved me considerable squinty eye moments trying to measure it from a page in millimetres and working centimetres from that. Can I ask how you achieved it ?


  • Advertisement
  • Registered Users, Registered Users 2 Posts: 5,143 ✭✭✭locum-motion


    I think the original lamp is just two dimensional (coz it's description says it "scales the wall") but I for one think it would work very well in three dimensions.


  • Registered Users, Registered Users 2 Posts: 249 ✭✭Frigating


    Muahahaha wrote: »
    You absolute legend, I can't thank this post enough ! I think you've saved me considerable squinty eye moments trying to measure it from a page in millimetres and working centimetres from that. Can I ask how you achieved it ?

    Print screened it and opened in paint.net. Cut the image so the lamp fit perfectly in a rectangle. Resized so it was full size (using the height - the width was a bit off, but I think that might have been the lamp shade). Drew all those odd lines on it. The program gave me the length of the lines. Subtracted the length of the joints (assuming them to be one inch) to get only the pipe length outside the joints.

    And you're welcome! :)


  • Registered Users, Registered Users 2 Posts: 2,781 ✭✭✭amen


    Don't forget copper is conductive. Make sure you correctly and safely wire the lamp and ensure that you cannot get a shock from touching the stand.


  • Registered Users, Registered Users 2 Posts: 19,717 ✭✭✭✭Muahahaha


    amen wrote: »
    Don't forget copper is conductive. Make sure you correctly and safely wire the lamp and ensure that you cannot get a shock from touching the stand.

    For sure, I'm lucky to have a sparks in the family so he said to ensure it's earthed well and that he'd give it a quick once over for me just in case.
    Frigating wrote: »
    Print screened it and opened in paint.net. Cut the image so the lamp fit perfectly in a rectangle. Resized so it was full size (using the height - the width was a bit off, but I think that might have been the lamp shade). Drew all those odd lines on it. The program gave me the length of the lines. Subtracted the length of the joints (assuming them to be one inch) to get only the pipe length outside the joints.

    And you're welcome! :)

    Well thanks a million again, it is a great help:) Will put up some pics of the final piece when it gets finished.


  • Registered Users, Registered Users 2 Posts: 788 ✭✭✭pillphil


    IT COSTS HOW MUCH? :eek:

    This might be of some use, she bolted the pipes to the wall though, so balance wasn't too important to her.

    http://www.nelliebellie.com/diy-pipe-lamp/

    cwts2-collage11.jpg


  • Advertisement
Advertisement