Advertisement
If you have a new account but are having problems posting or verifying your account, please email us on hello@boards.ie for help. Thanks :)
Hello all! Please ensure that you are posting a new thread or question in the appropriate forum. The Feedback forum is overwhelmed with questions that are having to be moved elsewhere. If you need help to verify your account contact hello@boards.ie
Hi there,
There is an issue with role permissions that is being worked on at the moment.
If you are having trouble with access or permissions on regional forums please post here to get access: https://www.boards.ie/discussion/2058365403/you-do-not-have-permission-for-that#latest

Fencing Question

  • 08-05-2013 2:57pm
    #1
    Registered Users, Registered Users 2 Posts: 73 ✭✭


    Hi,

    I am putting up 6x6 panel fencing, the standard b&q horizontal slat panels, to cover a concrete wall. My question is, is it ok to screw the panels straight into the wall or will i have to screw in a wooden rail at the top and bottom of the wall and then attach the fencing to the rails?

    I have the wood for the rail and was also give 3 inch concrete screws, but i am wondering if the panels can go straight on the wall. I measured the thickest part of the fence and which the screws would go through and this leaves me about 3/4 of an inch to an inch going into the concrete wall.

    Hope this makes enough sense!

    Thanks.


Comments

  • Registered Users, Registered Users 2 Posts: 1,078 ✭✭✭RoryMurphyJnr


    You're probably better off putting the rails onto the wall then the panels onto the rails.
    Just my 2 cents worth


  • Registered Users, Registered Users 2 Posts: 193 ✭✭Philip82


    Id agree with Rory, plus if its on rails the fence can breath and the water and dampness wont be rotting its way through the back of the panel.


  • Registered Users, Registered Users 2 Posts: 3,669 ✭✭✭policarp


    I would just put packers at every screw fixing.
    No need for rails IMO.


  • Registered Users, Registered Users 2 Posts: 2,187 ✭✭✭k123456


    No Need for rails, the panels are pressure treated. I use 6mm express nails, much quicker than screws

    When you buy the panels, buy ones as square as possible, if there is a bow on one of the two sides, they wont meet

    If you mount the squarest panel first, then mount the next one . If the next one wont meet the first exactly (slight bow), use a clamp (or muscle ) and screws to pull the panels together


  • Banned (with Prison Access) Posts: 15,857 ✭✭✭✭paddy147


    k123456 wrote: »
    No Need for rails, the panels are pressure treated. I use 6mm express nails, much quicker than screws

    When you buy the panels, buy ones as square as possible, if there is a bow on one of the two sides, they wont meet

    If you mount the squarest panel first, then mount the next one . If the next one wont meet the first exactly (slight bow), use a clamp (or muscle ) and screws to pull the panels together

    And what happens when you need to replace a fence panel??;)

    Fence panels do rot/break after a while (especially when in constant contact with a wet wall)..they can also be easily wind damaged or broken by kids playing in the garden or playing football.

    You will make absolute shyte of the wall if you do it this way,and you will then need to drill new holes for the new express nails.:(


  • Advertisement
  • Banned (with Prison Access) Posts: 15,857 ✭✭✭✭paddy147


    OP...drill/fit some pressure treated 3 x 2 lengths of wood to the wall.Install the 3 inch side on the flat against the wall.


    These can be your rails/posts.



    Then use some outdoor decking screws or stainleess steel screws to screw on the fence panels to the lengths of 3 x 2.





    If you even need to replace a fence panel,then 2 minutes with a screwgun,off with the screws and old fence panel and on with the new one.



    Job done.


  • Registered Users, Registered Users 2 Posts: 73 ✭✭Winston79


    Thanks for all the info guys.

    I'll go ahead and do the rails, have the stuff for it anyway.

    Agian thanks for the help!


Advertisement