Advertisement
If you have a new account but are having problems posting or verifying your account, please email us on hello@boards.ie for help. Thanks :)
Hello all! Please ensure that you are posting a new thread or question in the appropriate forum. The Feedback forum is overwhelmed with questions that are having to be moved elsewhere. If you need help to verify your account contact hello@boards.ie
Hi there,
There is an issue with role permissions that is being worked on at the moment.
If you are having trouble with access or permissions on regional forums please post here to get access: https://www.boards.ie/discussion/2058365403/you-do-not-have-permission-for-that#latest

radiator not working

  • 30-01-2012 9:19pm
    #1
    Registered Users, Registered Users 2 Posts: 129 ✭✭


    unusual problem..al rads upstairs and downstairs except one in upstairs bedroom...tried bleeding ect....i then disconnected both flow and return and ran hose out window clamped on hose and switched on heating,again no flow at all couple dribbles ..what could stop water coming to one rad??


Comments

  • Registered Users, Registered Users 2 Posts: 2,842 ✭✭✭Billy Bunting


    Is the pipework plastic ?? Qualpex/Acorn


  • Registered Users, Registered Users 2 Posts: 129 ✭✭doublejj


    yeah qualpex


  • Registered Users, Registered Users 2 Posts: 2,842 ✭✭✭Billy Bunting


    possible kinked pipe. :confused:


  • Registered Users, Registered Users 2 Posts: 129 ✭✭doublejj


    maybe but wonder how and where.....had this rad off for while before with cople others heat returned to others after bleeding but not this...possible airlock i wonder?


  • Registered Users, Registered Users 2 Posts: 509 ✭✭✭DanWall


    Is the system balance? The furthest radiator from the pump must have the locksheild valve wide open, the other radiators must be reduced progressively depending on distance from the pump to allow pressure to reach the furthest radiator.


  • Advertisement
  • Registered Users, Registered Users 2 Posts: 44 dm1388


    you could try turning off all the other rads and leave the heating on, this has worked a treat for me many times


  • Registered Users, Registered Users 2 Posts: 1,632 ✭✭✭heinbloed


    The OP asks:
    what could stop water coming to one rad?

    Bad or no system balancing at all.


  • Registered Users, Registered Users 2 Posts: 129 ✭✭d o'c


    doublejj wrote: »
    unusual problem..al rads upstairs and downstairs except one in upstairs bedroom...tried bleeding ect....i then disconnected both flow and return and ran hose out window clamped on hose and switched on heating,again no flow at all couple dribbles ..what could stop water coming to one rad??

    disconnected but with rad valves still attached?
    is it a trv type valve? stuck/ clogged valve possibly?


  • Registered Users, Registered Users 2 Posts: 1,429 ✭✭✭Cedrus


    Is it a new or old installation? has the rad just stopped or has it been off for a while? Dirty install if new (plastic swarf in valve or rad) Sludge//rust if old? TRVs can stick badly specially if they're fitted against the flow or used as isolation valves during the summer.


  • Registered Users, Registered Users 2 Posts: 129 ✭✭doublejj


    its about thirteen years old .....tried all of the above still no joy....nowater flowing there at all


  • Advertisement
  • Closed Accounts Posts: 450 ✭✭Marcanthony


    doublejj wrote: »
    its about thirteen years old .....tried all of the above still no joy....nowater flowing there at all

    you have a dead leg.:eek: or a kinked pipe

    Have you got a high water demand from your cylinder/s or other appliances.


  • Registered Users, Registered Users 2 Posts: 129 ✭✭doublejj


    low demand if anything.....cannot find a gauge on system to check pressure,or see how its pressurised....looks like a closed circuit


  • Closed Accounts Posts: 450 ✭✭Marcanthony


    doublejj wrote: »
    low demand if anything.....cannot find a gauge on system to check pressure,or see how its pressurised....looks like a closed circuit

    well its either a kinked pipe or a dead leg then.Do you know the distance between the pipework from the heat sourse to that radiator and size of pipework.

    Or is the pipework creating air pockets. 90 degree bends on the pipework restricting the flow and causing the water to become stagment in that area.
    A common example of this would be a sharp bend on the flow pipe feeding a hot water cylinder.


Advertisement