Advertisement
If you have a new account but are having problems posting or verifying your account, please email us on hello@boards.ie for help. Thanks :)
Hello all! Please ensure that you are posting a new thread or question in the appropriate forum. The Feedback forum is overwhelmed with questions that are having to be moved elsewhere. If you need help to verify your account contact hello@boards.ie
Hi there,
There is an issue with role permissions that is being worked on at the moment.
If you are having trouble with access or permissions on regional forums please post here to get access: https://www.boards.ie/discussion/2058365403/you-do-not-have-permission-for-that#latest

Record player is running slighly slow?

  • 07-03-2011 4:43pm
    #1
    Registered Users, Registered Users 2 Posts: 12,354 ✭✭✭✭


    Hey, I hope this is the correct spot for this, looks like it should be though:)

    Anyways, we were clearing stuff out of my grandfather's house, came across a box of old records & a record player. My interest was piqued, so I grabbed it, took it home & tried it out. Initially I thought it was working fine, I tested it extremely briefly, and apart from a tiny bit of dust on the needle it seemed fine.

    Now I've tried it a bit more, and the player is playing the records slightly slowly. It's noticeable when you hear lyrics etc. but it's not hugely noticeable (i.e. if you walk past you won't notice it, unless you actively listen to the music)

    I have no idea about record players or anything like that. Is there something that can be done for this? Is it something fundamentally wrong with the player or is there something I can do?

    Any/all assistance would be greatly appreciated!


Comments

  • Closed Accounts Posts: 3,293 ✭✭✭Fuzzy Clam


    Make/model ?


  • Registered Users, Registered Users 2 Posts: 12,354 ✭✭✭✭dulpit


    Uhm... It says STM Audio, SRP1 on it. It also says Belt drive next to where the needle hits the vinyl.. (sorry to sound like a noob)


  • Registered Users, Registered Users 2 Posts: 6,163 ✭✭✭ZENER


    Is there a label on the underneath stating the voltage/frequency it's designed to work from ?

    Ken


  • Registered Users, Registered Users 2 Posts: 12,354 ✭✭✭✭dulpit


    ZENER wrote: »
    Is there a label on the underneath stating the voltage/frequency it's designed to work from ?

    Ken

    I don't know, but I shall check the moment I get home...


  • Registered Users, Registered Users 2 Posts: 12,354 ✭✭✭✭dulpit


    ZENER wrote: »
    Is there a label on the underneath stating the voltage/frequency it's designed to work from ?

    Ken

    240V & 50 Hz

    any ideas?


  • Advertisement
  • Registered Users, Registered Users 2 Posts: 2,323 ✭✭✭Slaphead07


    if it's a belt drive it might be that - they collect dust and dirt and start slipping. If you can lift off the platter easily you'll see a thick rubber band going from one small wheel around the circumference of the platter. Clean this with Pledge furniture polish (no other brand will do! honest!) and put it back making sure it's all level. Listen again.

    Otherwise it would be as Ken suspects a voltage issue and probably not worth fixing.


  • Registered Users, Registered Users 2 Posts: 6,163 ✭✭✭ZENER


    I was thinking it may have been a frequency issue. Some mains decks use a synchronous motor working off the mains frequency. I was just curious if it was a 60Hz model from the states or some other country that used 60Hz mains. Anyway, irrelevant now.

    With DC motors there is usually a speed adjustment internally within the motor or on a pcb elsewhere in the player. If the belt advice above doesn't work out perhaps I could check it out for you. PM me if you like.

    Carry on :)

    Ken


Advertisement