Advertisement
If you have a new account but are having problems posting or verifying your account, please email us on hello@boards.ie for help. Thanks :)
Hello all! Please ensure that you are posting a new thread or question in the appropriate forum. The Feedback forum is overwhelmed with questions that are having to be moved elsewhere. If you need help to verify your account contact hello@boards.ie
Hi there,
There is an issue with role permissions that is being worked on at the moment.
If you are having trouble with access or permissions on regional forums please post here to get access: https://www.boards.ie/discussion/2058365403/you-do-not-have-permission-for-that#latest

play in the headset

  • 22-08-2009 10:33pm
    #1
    Closed Accounts Posts: 174 ✭✭


    There seems to be some play in my headset.I think thats what its called,I have changed my stem and now I have noticed some play there.When I am descendings started to rattle not that much but still a rattle.So I then changed back to my original stem and the same thing has happened.Are the bearings shot cant be as I have not used the bike that much.Its a focus cayo the bike Imean.Any one have any idea what is wrong ,the bike is about 8 months old and I have only used it in fine weather that will tale you how much I have used it.This is very disappointing I have tried to email wiggle but no responce would the warrenty cover this?:mad::mad:


Comments

  • Registered Users, Registered Users 2 Posts: 156 ✭✭Tau


    You could try this - it worked for me with a similar problem:

    http://www.youtube.com/watch?v=RRFqU07u8DE


  • Registered Users, Registered Users 2 Posts: 4,833 ✭✭✭niceonetom


    Warranty? Do you bring a radio back to the shop because you're unable to fathom how to tune in a station? Or shoes when the laces become untied?

    from parktool:
    The bolt in the top cap will put pressure on the stem, which presses on washers below the stem, which press on the bearing races, which press against the bearings.

    NOTE: The cap and bolt at the top of the stem do not secure the stem onto the steering column. The bolt or bolts on the side of the stem keep the stem from moving once the adjustment is made. The cap is used for bearing adjustment only.
    Begin by removing the adjusting bolt in the center of the steering column. Next, remove the top cap. There may be a star-shaped nut or other fittings inside the steering column. The bolt threads into this fitting and pulls on the fork against the headset bearing surfaces, which acts to tighten the adjustment. Note the height of the steering column relative to the stem. It should be about 3mm (1/8") below the level of the stem. The stem needs to press down on the spacers in order to adjust the bearings. If the steering column is level with the top of the stem, another spacer is needed below the stem.

    1. Remove bolt and top cap to inspect steering column. Lubricate adjusting bolt and re-install cap and bolt by hand only. DO NOT TIGHTEN.
    2. Loosen stem bolt(s) that secure stem to the steering column. Lubricate these bolts if they are dry. NOTE: DO NOT LUBRICATE INSIDE STEM OR ON STEERING COLUMN SURFACE.
    3. Wiggle the stem side to side to see that it is loose. If the stem is jammed or rusted frozen to the steering column, no adjustment can be made.
    4. Align stem straight to wheel and gently secure the top bolt. Stop when any resistance is felt.
    5. Tighten stem bolt(s).
    6. Check for play by pulling back and forth on fork. Turn the handlebars in different directions while checking for play. There may be play at this early setting. Use care when grabbing suspension forks, because the legs may have play. Grab upper portion of fork.
    7. To adjust bearings, LOOSEN STEM BOLT(S).
    8. Turn adjusting bolt in center cap only 1/8th turn clockwise.
    9. Secure stem bolts, check for play again.
    10. Repeat adjustments as above until play disappears. Remember to loosen stem bolts before turning adjusting bolt in cap.
    11. Check alignment of stem and tighten stem binder bolts fully.

    NOTE: Another test of play is to place the bike on ground and grab the front brake tightly. Press downward on the handlebars and rock the bike forward and back. A knocking sensation may indicate a loose headset. In effect this does the same thing as grabbing and pulling on the fork. However, play in the brake caliper arms may also cause a knocking. Front suspension forks may also have play in the legs, which can cause a knocking.If the adjustment seems very tight, there may be other problems in the headset. Bearing surfaces may be worn out, or the ball bearing retainers may be upside down, or a seal may be improperly aligned. If play always seems present no matter the adjustment, the steering column may be too long for the stem and top cap. Add spacers beneath stem in this case.


  • Closed Accounts Posts: 174 ✭✭horizon26


    thanks Tau and niceone tom try both options tomorrow good night to both of you.


  • Registered Users, Registered Users 2 Posts: 1,714 ✭✭✭Ryaner


    I recently cleared out my headset and reinstalled it. Had very similar problems. Turns out I had put one of the bearings back in upside down the first time around which get either the wobble, or a very stiff headset when I tighten enough. Stupid mistake I know but something to watch for. Easy enough to pick things up wrong while holding the fork up and trying to screw things back together.


Advertisement