Problems setting up tp-link td-w8910g with BTIreland

silversurfer

Hi all,
I bought myself a tp-link td-w8910g to replace the old ZyXEL Prestige 623R Router as I need wireless along with the standard RJ45 connection to the desktop.

Would anyone know how to set it up,maybe if someone had the standard BT settings?
I've gone into http://192.168.1.1/ to do the settings but I'm a bit lost with all the jargon?
Have the password for the ISP entered etc but it won't connect to the Web


Thanks,
S

Little-Devil

silversurfer wrote:

Hi all,
I bought myself a tp-link td-w8910g to replace the old ZyXEL Prestige 623R Router as I need wireless along with the standard RJ45 connection to the desktop.

Would anyone know how to set it up,maybe if someone had the standard BT settings?
I've gone into http://192.168.1.1/ to do the settings but I'm a bit lost with all the jargon?
Have the password for the ISP entered etc but it won't connect to the Web


Thanks,
S

Encapsulation: PPPoE
Multiplexing: LLC Based
VPI: 8
VCI: 35

Your username@btbb
password: **********

That should be all you need. Can you connect with Etherenet? Is the wireless built into your laptop / PC or are you using a wireless usb adapter?

silversurfer

I've already set it up as you suggested
Encapsulation: PPPoE [selected]
Multiplexing: LLC Based [LLC/SNAP-BRIDGING]
VPI: 8 [selected]
VCI: 35 [selected]

Your username@iolbb [this is not btbb on my old ZyXEL router]
password: **********


Diagnostics return the following?
pppoe_8_35_2 Diagnostics

Your modem is capable of testing your DSL connection. The individual tests are listed below. If a test displays a fail status, click "Rerun Diagnostic Tests" at the bottom of this page to make sure the fail status is consistent. If the test continues to fail, click "Help" and follow the troubleshooting procedures.
Test the connection to your local network
Test your ENET(1-4) Connection: PASS Help

Test your Wireless Connection: PASS Help


Test the connection to your DSL service provider
Test ADSL Synchronization: PASS Help

Test ATM OAM F5 segment ping: F4 FAIL Help

Test ATM OAM F5 end-to-end ping: F4 FAIL Help


Test the connection to your Internet service provider
Test PPP server connection: FAIL Help

Test authentication with ISP: PASS Help

Test the assigned IP address: PASS Help

Ping default gateway: FAIL Help

Ping primary Domain Name Server: PASS Help


Thanks,
s

center15

Sorry for hijacking the thread but would anyone have a spare ZyXEL BT router they may want to sell or better yet give away Will pay for postage. My existing one just packed up and I want to replace it with the same one. Cheers.

silversurfer

hi

Managed to get the following settings and will try them later tonight.
don't suppose anyone has encountered the Cell rate settings?

Router Type TP-LINK TD-W8910G

Login info
Service

username@iolbb or username@btbb [looks like this does not matter)
Password

Dial on Demand (with Idle) ? >0 must be greater than 0
PPI IP Extension ?
Use Static IP Address ?
Enable PPP Debug Mode ?

Protocol PPPoE
Multiplex LLC/ SNAP-BRIDGING

Virtual Circuit ID
VPI 8
VCI 35

Quality of service Type
ATM QoS Type CBR
Enabled

Cell Rate
Peak Cell Rate (PCR) ?? values: 1 to 980
Sustainable Cell Rate (SCR) ??
Maximum Burst Size (MBS) ??
Minimum Cell Rate (MCR) ??

Device Setup
IP Address 192.168.1.1
Subnet Mask 255.255.255.0

Enable DHCP server yes
Start IP Address 192.168.1.2
End IP Address 192.168.1.254
Leased Time (hours) 24


NOTE:
"If the routers IP address is 192.168.1.1, your PC's IC address must be within the range of 192.168.1.2 ~ 192.168.1.254, the gateway must be 192.168.1.1"

silversurfer

Works with these settings