Advertisement
If you have a new account but are having problems posting or verifying your account, please email us on hello@boards.ie for help. Thanks :)
Hello all! Please ensure that you are posting a new thread or question in the appropriate forum. The Feedback forum is overwhelmed with questions that are having to be moved elsewhere. If you need help to verify your account contact hello@boards.ie
Hi there,
There is an issue with role permissions that is being worked on at the moment.
If you are having trouble with access or permissions on regional forums please post here to get access: https://www.boards.ie/discussion/2058365403/you-do-not-have-permission-for-that#latest

Noisy Pump - driving me nuts!

  • 23-02-2007 1:06pm
    #1
    Registered Users, Registered Users 2 Posts: 3


    I have a 3 Bar Stuart Turner double-ended shower pump in my apartment airing cupboard. It provides a fantastic shower but the noise it makes is driving me nuts.
    There doesn't seem to have been much care put into the original installation (before I moved in), with the flexible hoses kinked and set at different lengths on the pipes. The pump is hanging from the pipework and it's not fully set on the floor. Also when the pump is on it seems to using the airing cupboard as a sounding board.

    I've done the usual Googling and have a fair idea of what I need to do.

    The plan at the moment is as follows;

    Turn off power supply to pump
    Turn off HOT/COLD water supply & drain system
    Remove flexible hoses from pipework and remove pump
    Layer thick piece of carpet on hotpress floor.
    Put cork tile on this
    Then paving slab
    Another cork tile
    Place Pump on top of this with feet set on rubber washers
    Cut the copper pipes to the correct length and re-attach the flexible hoses.
    Support all pipework with pipe clips and wrap all pipes in the hotpress with foam rubber insulation
    Layer the bottom half of the hotpress walls with double layer of cork tiles to reduce sound board effect
    Seal door with draft strip all-round with rubber weather strip on the bottom.
    Cup of Tea!!:D

    My main area of concern is the removal and re-fitting of the pump. I have basic plumbing skills but for some reason working around the pump is making me nervous. Is the inital removal as simple as I make it out in steps 1-3 or is there something else I need to look out for.

    Any help or tips greatly appreciated!


Comments

  • Registered Users, Registered Users 2 Posts: 2,876 ✭✭✭Borzoi


    CPAMG wrote:
    My main area of concern is the removal and re-fitting of the pump. I have basic plumbing skills but for some reason working around the pump is making me nervous. Is the inital removal as simple as I make it out in steps 1-3 or is there something else I need to look out for.

    !

    I replaced one of these before Christmass, not too big a job. Did it in an hour or two, but that's without the fancy mount system. I'd be a little concerned that you're introducing too much vibration into the system. The instructions suggest that the pumps anti vib pads be placed directly onto a solid floor. Mine does still make noise, but it's not vibration, and I have put it in a small foam lined box to help kill the noise, sort off works!

    No need to fully drain the system, just close the 2 outlet (one hot, one cold) from the tanks. Then turn on the taps, to let as much of the water out as possible. Even still you'll probbaly have 2-3 litre of water in the pipes, when you take off the flexibles, so make sure you've a bucket handy.


  • Registered Users, Registered Users 2 Posts: 3 CPAMG


    Cheers for that!

    The main reason I'm putting in the 'fancy mount' :) system is that some of the copper pipes were cut short by the previous installer and the pump will not reach the floor. So I'm going to bring the floor to the pump so to speak.

    I'll get the bucket ready!


Advertisement