PS3 Connection problem!

Super Sidious · 11-02-2008 02:16AM #1

Hi ive searched the net and found plenty of guides including some on boards, but im about to pull my hair out at the fact my ps3 wont go back online... I have set up a static ip and port forward everything, in net connections on ps3 it gets to obtain ip address succeded, internet connection failed error 80710102...

Ive looked at guides followed them word for word and still no success!

im using eircom netopia router, are my dns servers wrong i left them at default, then changed them to different eircom ones and still no luck! please help!

Rb · 11-02-2008 03:37AM

Which netopia router?

DILLIGAF · 11-02-2008 04:07AM

yeah we had a serious problem with this for ages, then we fixed it! would you like to know how???

We bought a 25 meter long ethernet cable!hahahaha seriously,it was getting on my tits so much! I had done everything I could think of in all my years computing and this thing wasn't budging! I finally sorted my IP address issue but then internet connection wasn't going to work at all! So like I say, a bloody long cable, and viola!10 seconds later I was online!not exactly great advice but its still advice!

guil · 11-02-2008 09:48AM

he never said he was tryin to connect wirelessly
flynner did ya put the same dns as the one on the netopia home page

Clover · 11-02-2008 10:12AM

the firewall on the eircom router may be your problem , set it to low .

guil · 11-02-2008 11:15AM

that shouldnt matter cos i set up a friends ps3 the other day and its connectin wirelessly with nat 2 and the firewall is still on medium on a netopia router

Super Sidious · 11-02-2008 05:30PM

Ive had it working before without using a static ip address, but ever since i made it static it dont work, ive followed guides to a T and it still dont work!

Im connecting it wirelessly through eircom netopia 2247nwg, it says the dns error after it says ip connecting, then it stops at internet connection!

Basically just wana know, when i make the ip settings on ps3 i use 1 ip higher than what my laptop is set too, eg. xxx.xx.xx.136 & xxx.xx.xx.137...

What DNS servers do i use for ps3 and laptop, should i make them the same, is there any special dns servers i should use? I have upnp set to enable on router and ps3, dont wana use any wires as theres enough going around the room as it is!

Cheers for any help!

Clover · 11-02-2008 05:54PM

yeh make the dns the same as it is on the laptop , if your isp is eircom use these

eioneill · 11-02-2008 06:10PM

Folks I robbed this off some other site. Used the guide to set up both mine and my brothers routers. Fairly straight forward.

hey guys, heres a guide to having absolutley FLAWLESS ps3 online, very important parts shall have an asterix (*) to the left hand side of the post,
i shall also give brief explanations of why youre doing these things, and what they actually DO:

basically your ps3 connection has a NAT type , this basically says how your connection to your router is, TYPE 1 means its directly connected to the internet so its perfect, TYPE 3 means it can connect to the internet but the connection isnt perfect/very laggy, a result of this is not being able to go into chat rooms, ea nation games not working etc. well we try to get NAT type 2 which is wirelessly connected to the internet , but perfectly connected here we go!!

*give your ps3 a static ip address*
*okay this isnt too complicated, see every time a router gets accessed by a device (ps3, desktop, laptop etc.) it assignes it an ip address randomly depending on who logs in first,

on ps3
disable the media server function in 'network settings'
do an 'automatic' network connection and see if nat type 3 comes up at the end, if so, were on track

we need our ps3 to have an ip address that isnt given out randomly, as we will need it to have the same address,so you write down a new ip address, say 192.168.1.150 we use .150 because you probably will never have 150 devices on your router at any given time!

*find out our internets ip details*
i had awful guff with this online because bad wording of ip addresses and such was used , SO I WILL MAKE THIS CLEAR

*run a command prompt, on your desktop click 'start'-'run'-'cmd' in the command prompt , type ipconfig/all and click 'enter'

*now, write down the numbers for these addresses: IP GATEWAY,DNS SERVER 1, DNS SERVER 2 they will be used later on.

*fiddling with your router*(in the good way!)
*okay , now we are going to open some ports on your netopia router, DONT WORRY ITS NOT DANGEROUS, because we will only let these ports be opened when your ps3 'asks for them' so to speak, and considering your ps3 doesnt get viruses, you are safe!

*in your internet address bar type in your 'IP GATEWAY' you just got from the command prompt, just the numbers and dots, no need for a 'www' or any of that! on netopia routers the gateway is generally 192.168.1.254 so i will use that for now.

type 192.168.1.254 in the browser address window. and your netopia router page should appear, im gonna make this as easy as possible , so bear with me for a minute, were now going to 'open' and 'enable' the ports and 'enable' your ps3's ip address to know to recieve these ports.

*okay click EXPERT MODE on the left hand column, click 'YES , ENTER EXPERT MODE', double click the word 'configure, go down and click on 'NAT' click 'STATIC NAT' click ythe dropdown icon, see if your ip address is there, if so click it, click on done, if this works, igore the paragraph in brackets

(if not i think you have to sign into psn using the new ip beforehand, im not sure, to do that just use the custom ip and use the same settings but use you GATEWAY as the bar saying DEFAULT ROUTER , then come back to this step)

now im going to list a range of ports and what to do with them , we will call the example port aaaa .
click on NAT as you did earlier,(notice how the ps3 ip is there , listed under static ip? thats good)
click DEFINE CUSTOM SERVICE click in 'PORT FORWARDING' , select next , type anything in the service name, something that you will know its related to the ps3,

see the settings for 'global port range' if its only one port thats being entered enter the same port in the left and right hand boxes, in every case , enter the lower port in the box below saying 'base port' even if theres only one port, and chage the TCP/UDP settings according to every port.

heres the ports , repeat the same process for each one, after that window, select the static ip address you made in the drop-down list so it gets forwarded only for the ps3

* TCP port 80
TCP port 443
TCP port 5223
UDP port 3478-3479
UDP port 3658-3659

*now we 'enable' them all, when your done, click NAT on the left hand side, click the dropdown menu that has 'age of empires' written on it and scroll to the bottom, click on the ports you made with the asterix beside them (*) and click enable , then enter the ps3 ip address in the bar , to 'enable them just for the ps3' okay ,

*now click 'configure ' on the left and then click 'connection ' and tick the box that says "upnp"

now,to summarise, we should have , when we click NAT on the left hand column, a:

static NAT address, enabled, thats the ip youre going to use on your ps3
7 ps3 ports, all enabled to the 'host device' of your ps3's ip

*now , enter basic mode, click firewall, and set to low, this isnt dangerous as long as you have a desktop firewall such as windows or mcafee etc...
save changes, and RESTART YOUR ROUTER!

now, turn your ps3 off, then on again , now go to Network settings and click network settings, im putting this in bullet form for easiness

-wireless/wired(though this guide is based on a wireless connection)
-CUSTOM
-enter security settings
-now for your ip info CLICK MANUAL
-where it says 'ip address' enter the STATIC IP ADDRESS YOU MADE UP
-subnet mask is normally 255.255.255.0
-DEFAULT ROUTER, this wants you to input your GATEWAY number you wrote down
-DNS 1/primary , enter the one you wrote down,

i dont think the ps3 needs it , try it without using the 2nd one,

-cick NEXT
-'proxy server' DONT ENABLE THAT
-upnp , enable if you could in your router

thats all , save settings and do connection test, see what nat type comes up at the end, if its 2 , its perfect! dont do anyhting to your router and congratz! if not , perhaps a bit of the guide was overlooked, if that isnt the case either leave me a post and ill try and help,

eioneill

Clover · 11-02-2008 06:54PM

i tried my ps3 there a few moments ago and i was getting dns errors also ( bt connection ) i went into the netopia router and it said dns unavailable.

so i hit disconnect and the reconnected and i got the dns again from my isp and i ran the internet connection test on the ps3 and it was back to normal.

Super Sidious · 12-02-2008 12:43AM

How do you assign static IP to ps3 when your starting guide above?

Super Sidious · 12-02-2008 12:47AM

and should i have static nat enabled on router...

all my nats are going to my ip address thats right ye?

Clover · 12-02-2008 11:17AM

flynner13 wrote: »

and should i have static nat enabled on router...

all my nats are going to my ip address thats right ye?

yes , your ports should be open for the ip # the ps3 is getting from the router.

eioneill · 12-02-2008 12:31PM

IN ADDITION TO ABOVE GUIDE

I would advise to do your settings on PS3 1st. Then when you are opening the ports on your router you will b given a drop down menu to select the static IP you gave to your PS3

Super Sidious · 12-02-2008 02:58PM

I connected yesterday, but got kicked out mid game of tiger woods...even opened up ports for tiger... how do i set up an ip for the ps3? like it says i can direct my browser to 192.168.1.xx = ps3 ip...

KoA-Ollie · 12-02-2008 08:45PM

I have this Nat 3 problem aswell. I have 3G Broadband set up to my PS3 by a cross-over cable and have tried lots of different things to fix it. Anyone have any ideas?

12-02-2008 09:15PM

Is there anyway that the firewall errors people are having ,are caused by the ps3's architecture ?

Is the ps3 designed with the networking at it's core ?

Sorry if it's blubberish I'm speaking :eek:

guil · 13-02-2008 10:54PM

flynner dont click static nat i couldnt even sign into psn when i enabled that just follow the guide above and it will work i done it in november and never had a problem since

30-03-2008 02:31AM

This link is another posted about the nat issues ,but I still can't get NAT2.

http://www.portforward.com/english/routers/port_forwarding/Netopia/2247NWG-VGx/PS3_NAT_Type_3_to_2.htm

thewheel2.0 · 30-03-2008 02:08PM

eioneill wrote: »

-upnp , enable if you could in your router

I ticked this box in the router settings and went to my PS3 and its says upnp - not available...
Any one have any ideas?

EDIT : Also is this important for online gaming?

weeder · 30-03-2008 05:18PM

ok whoevery said type 2 is wireless is wrong, ive had type 2 on wired before but as of a few days ago it seems to not be working(probabaly overlooking somthing) so at the moment ive got ip passthrough enabled (TYPE1 )

087dannyboy · 31-03-2008 12:11AM

I originally had a NAT 3 then opened some ports and got NAT 2 and all games were working fine but now after the latest PS3 firmware update its put itself back to NAT 3 and i cannot seem to change back. So im just wondering has this happened to many other people and has anyone solved it and got back to Nat 2? And if so how? Cheers .

Plug · 31-03-2008 08:09AM

eioneill wrote: »

*run a command prompt, on your desktop click 'start'-'run'-'cmd' in the command prompt , type ipconfig/all and click 'enter'

*now, write down the numbers for these addresses: IP GATEWAY,DNS SERVER 1, DNS SERVER 2 they will be used later on.

My ones are all the same, what am I doing wrong?

Plug · 31-03-2008 08:20AM

eioneill wrote: »

Folks I robbed this off some other site. Used the guide to set up both mine and my brothers routers. Fairly straight forward.

hey guys, heres a guide to having absolutley FLAWLESS ps3 online, very important parts shall have an asterix (*) to the left hand side of the post,
i shall also give brief explanations of why youre doing these things, and what they actually DO:

basically your ps3 connection has a NAT type , this basically says how your connection to your router is, TYPE 1 means its directly connected to the internet so its perfect, TYPE 3 means it can connect to the internet but the connection isnt perfect/very laggy, a result of this is not being able to go into chat rooms, ea nation games not working etc. well we try to get NAT type 2 which is wirelessly connected to the internet , but perfectly connected here we go!!

*give your ps3 a static ip address*
*okay this isnt too complicated, see every time a router gets accessed by a device (ps3, desktop, laptop etc.) it assignes it an ip address randomly depending on who logs in first,

on ps3
disable the media server function in 'network settings'
do an 'automatic' network connection and see if nat type 3 comes up at the end, if so, were on track

we need our ps3 to have an ip address that isnt given out randomly, as we will need it to have the same address,so you write down a new ip address, say 192.168.1.150 we use .150 because you probably will never have 150 devices on your router at any given time!

*find out our internets ip details*
i had awful guff with this online because bad wording of ip addresses and such was used , SO I WILL MAKE THIS CLEAR

*run a command prompt, on your desktop click 'start'-'run'-'cmd' in the command prompt , type ipconfig/all and click 'enter'

*now, write down the numbers for these addresses: IP GATEWAY,DNS SERVER 1, DNS SERVER 2 they will be used later on.

*fiddling with your router*(in the good way!)
*okay , now we are going to open some ports on your netopia router, DONT WORRY ITS NOT DANGEROUS, because we will only let these ports be opened when your ps3 'asks for them' so to speak, and considering your ps3 doesnt get viruses, you are safe!

*in your internet address bar type in your 'IP GATEWAY' you just got from the command prompt, just the numbers and dots, no need for a 'www' or any of that! on netopia routers the gateway is generally 192.168.1.254 so i will use that for now.

type 192.168.1.254 in the browser address window. and your netopia router page should appear, im gonna make this as easy as possible , so bear with me for a minute, were now going to 'open' and 'enable' the ports and 'enable' your ps3's ip address to know to recieve these ports.

*okay click EXPERT MODE on the left hand column, click 'YES , ENTER EXPERT MODE', double click the word 'configure, go down and click on 'NAT' click 'STATIC NAT' click ythe dropdown icon, see if your ip address is there, if so click it, click on done, if this works, igore the paragraph in brackets

(if not i think you have to sign into psn using the new ip beforehand, im not sure, to do that just use the custom ip and use the same settings but use you GATEWAY as the bar saying DEFAULT ROUTER , then come back to this step)

now im going to list a range of ports and what to do with them , we will call the example port aaaa .
click on NAT as you did earlier,(notice how the ps3 ip is there , listed under static ip? thats good)
click DEFINE CUSTOM SERVICE click in 'PORT FORWARDING' , select next , type anything in the service name, something that you will know its related to the ps3,

see the settings for 'global port range' if its only one port thats being entered enter the same port in the left and right hand boxes, in every case , enter the lower port in the box below saying 'base port' even if theres only one port, and chage the TCP/UDP settings according to every port.

heres the ports , repeat the same process for each one, after that window, select the static ip address you made in the drop-down list so it gets forwarded only for the ps3

* TCP port 80
TCP port 443
TCP port 5223
UDP port 3478-3479
UDP port 3658-3659

*now we 'enable' them all, when your done, click NAT on the left hand side, click the dropdown menu that has 'age of empires' written on it and scroll to the bottom, click on the ports you made with the asterix beside them (*) and click enable , then enter the ps3 ip address in the bar , to 'enable them just for the ps3' okay ,

*now click 'configure ' on the left and then click 'connection ' and tick the box that says "upnp"

now,to summarise, we should have , when we click NAT on the left hand column, a:

static NAT address, enabled, thats the ip youre going to use on your ps3
7 ps3 ports, all enabled to the 'host device' of your ps3's ip

*now , enter basic mode, click firewall, and set to low, this isnt dangerous as long as you have a desktop firewall such as windows or mcafee etc...
save changes, and RESTART YOUR ROUTER!

now, turn your ps3 off, then on again , now go to Network settings and click network settings, im putting this in bullet form for easiness

-wireless/wired(though this guide is based on a wireless connection)
-CUSTOM
-enter security settings
-now for your ip info CLICK MANUAL
-where it says 'ip address' enter the STATIC IP ADDRESS YOU MADE UP
-subnet mask is normally 255.255.255.0
-DEFAULT ROUTER, this wants you to input your GATEWAY number you wrote down
-DNS 1/primary , enter the one you wrote down,

i dont think the ps3 needs it , try it without using the 2nd one,

-cick NEXT
-'proxy server' DONT ENABLE THAT
-upnp , enable if you could in your router

thats all , save settings and do connection test, see what nat type comes up at the end, if its 2 , its perfect! dont do anyhting to your router and congratz! if not , perhaps a bit of the guide was overlooked, if that isnt the case either leave me a post and ill try and help,

eioneill

Lads, would someone please be able to write that out in more user friendly way. Im having a difficult time doing it. Im a noob when It comes to this kind of stuff. PLEASE!

087dannyboy · 31-03-2008 04:15PM

I dunno if this will help but it worked for me . My NAT also changed to type 3 after the update but i just start messin around with it and now have type 1 (wireless) .

Here's what i done I disabled all the ports i had opened to originally get type 2, Then went to PS3 network settings - internet connection settings - custom - wireless, at WLAN settings select Enter Manually and enter SSID and WEP key.

Then comes IP Address Setting And I selected PPPoE and it brings you to enter a user name and password And i entered the user name and password from my router when i restart connection Then DNS automatic and i entered MTU manual at 1500.
Then just Keep going to the end Proxy server Do not use UPnP enable. Test connection and type 1 Might not work for everyone but it worked for me .

31-03-2008 08:03PM

087dannyboy wrote: »

I originally had a NAT 3 then opened some ports and got NAT 2 and all games were working fine but now after the latest PS3 firmware update its put itself back to NAT 3 and i cannot seem to change back. So im just wondering has this happened to many other people and has anyone solved it and got back to Nat 2? And if so how? Cheers .

It's bollox, i reseted my router cause i was having PSN connection problems and started the whole process from scratch and it's still on NAT 3, basically no other way from my point of view of changing it now!!. Is everyone here Eircom?. I'm getting sick of there router boxes now tbh, even if somebody rings the house phone my connection will go!!.

Plug · 31-03-2008 08:10PM

gilberto_eire wrote: »

It's bollox, i reseted my router cause i was having PSN connection problems and started the whole process from scratch and it's still on NAT 3, basically no other way from my point of view of changing it now!!. Is everyone here Eircom?. I'm getting sick of there router boxes now tbh, even if somebody rings the house phone my connection will go!!.

Im with eircom:mad: I followed that guide and all i got was Nat -
Does anyone know a basic way of doing things. I don't even know what half the fcuking words on that guide mean. Its double dutch. Please will someone help.

087dannyboy · 31-03-2008 11:52PM

Plug wrote: »

Im with eircom:mad: I followed that guide and all i got was Nat -
Does anyone know a basic way of doing things. I don't even know what half the fcuking words on that guide mean. Its double dutch. Please will someone help.

Plug did you try what i did its just a couple of posts above this one

31-03-2008 11:59PM

Whats the eircom password ?

087dannyboy · 01-04-2008 12:14AM

311 wrote: »

Whats the eircom password ?[/quot

broadband1 is mine id say its the same for all

01-04-2008 12:21AM

I'm getting a pppoe ,name or password incorrect.

PS3 Connection problem!

Comments