nav[aria-label="Primary Navigation"] { padding: 0; & ul { list-style: none; width: 100%; display: flex; flex-direction: row; justify-content: start; align-items: start; gap: 30px; padding: 0; & li { margin: 0; } & ul li { list-style: none; } } }

Child Item

Need Help Please - Astec 63 - Installation/Engineering Manual

Durzo Bek

Hi,
I have recently moved into a house, which has a Astec 63 Alarm, I have successfully reset the Panel back to Factory settings and replaced a contact sensor for a door entry zone, (no open zones - all appears well now), however I now need to program the Full and Part Set settings, as there is no exit time on the Full, and as for Part Set, there is two PIRs that need to be disabled from that mode.
Would appreciate it very much if someone could provide me with a Install manual for Astec 63, as it would help me to determine if the alarm is fully functioning, or else I'll have to replace it with a new and different make/model.
Thanks in advance.
Durzo.

Find more posts tagged with

Quick Links

Comments

cmckeating

KoolKid wrote: »

If moisture was causing a short it should display tamper EOL. Probably a faulty device or a bad connection somewhere

Thanks . So classic wear and tear I'm guessing - the system is 7 years old with no issues to date.

I'm guessing one solution would be to check all contacts and replace every box cover. Not cheap, and probably more expensive than getting someone in .. However, bad news is that engineer code has been changed and I can't get through to installing engineer (Retec security) - hoping he's just turned his phone off for Christmas and he'll be back on the grid tomorrow.

cmckeating

Question for the Astec experts - and I can't find the answer in the engineers manual. I've an infrared sensor that I've had covered up for years due to a four-legged friend joining the household. Its now started triggered during FULL and PART set periodically - not sure why.

Its set up to be included in both FULL and PART set - unlike a second infrared in the hall, which is excluded from PART set. I'd like to exclude the other infrared from the FULL and PART set, but I can't find that command in the manual.

Any advice?

KoolKid

cmckeating wrote: »

Thanks . So classic wear and tear I'm guessing - the system is 7 years old with no issues to date.

I'm guessing one solution would be to check all contacts and replace every box cover. Not cheap, and probably more expensive than getting someone in .. However, bad news is that engineer code has been changed and I can't get through to installing engineer (Retec security) - hoping he's just turned his phone off for Christmas and he'll be back on the grid tomorrow.

A great life if hes able to turn the phone off????
Licencing rules mean you must have a 24 hour number I believe.
Don't know if you got sorted or not. But its probably just a matter of finding one faulty device.

KoolKid

cmckeating wrote: »

Question for the Astec experts - and I can't find the answer in the engineers manual. I've an infrared sensor that I've had covered up for years due to a four-legged friend joining the household. Its now started triggered during FULL and PART set periodically - not sure why.

Its set up to be included in both FULL and PART set - unlike a second infrared in the hall, which is excluded from PART set. I'd like to exclude the other infrared from the FULL and PART set, but I can't find that command in the manual.

Any advice?

Best way is to put it on soak test. Command 87 then some number , type: infred & set to YES.
Or delete it altogether. Disconnect the cables from the device , goto command 70 & rescan the PiRs . It will now only show the one thats still connected.Press Set to accept.

cmckeating

Perfect - thanks mate. I'll give that a blast

Lhisland12

Any chance you would send me that installation manual, my Astec 63d is going off randomly for a week now, maybe battery fault, thanks.

KoolKid

PMed you that manual. What is displaying when you disarm the system after an activation?

ehealo

Hi all. I too cold do with a copy of the Installation manual for the AZTEC intruder alarm. It would be greatly appreciated.

KoolKid

I Pmed you that.

peterk2016

Hi all,

I recently moved into a my new house, which has an astec 63 alarm fitted. I reconnected it to the power and brought it back to life, had to reset it to factory settings so I could disable it as the old code was unknown. Now I am looking for the engineering manual to reprogram it to use until I can fit an new system.

Thanks in advance,
Peter

KoolKid

Hi Peter
I have PMed you that manual.

peterk2016

Thanks a million, fingers crossed it will all go smoothly have a feeling it is on its last legs

Peter

peterk2016

Hi KoolKid, thanks for you help.

The only issue i have now is a tamper lid fault after I opened the box and cant seem to get rid of it.

Peter

KoolKid

Check the the white cover of the tamper spring is right behind the hole where the pin on the inside of the lid lines up. Its just below the holder for the left plastic screw.

peterk2016

I can see the spring through the hole and it is lined up with the pin of the upper cover but still no joy. The spring looks like it has seen better days. Is it done by pressure? Would there be a way to trick it into thinking the tamper has be fixed. Would another reset with the lower cover installed help?

Im scratching my head with this one.

DublinDilbert

peterk2016 wrote: »

I can see the spring through the hole and it is lined up with the pin of the upper cover but still no joy. The spring looks like it has seen better days. Is it done by pressure? Would there be a way to trick it into thinking the tamper has be fixed. Would another reset with the lower cover installed help?

Im scratching my head with this one.

The spring should have a white button pushed into the top of it. When you remove the cover this goes off centre, you need to recentre it before putting the cover back on.

Landtech

Hi,
Also having problems with Astec 63 alarm panel. Getting LED display, 15 Call Engineer, 22 Call Engineer intermittently. Cannot seem to set the alarm using the User Code as I do not hear the buzzer for arming. Also tested bells option on alarm panel and cannot hear outside bell ringing so may have a problem with outside bell.
Copy of Engineering manual would be appreciated if available

KoolKid

PMed you that manual.

Davwalsh03

Hi KoolKid, I was wondering if you could PM me the engineers manual for the astec alarm please?

Thank you so much for your help in advance

KoolKid

PMed you that manual.

Davwalsh03

Thank you so much for your help. Much appreciated

Rafal1976

Hi KoolKid, I was wondering if you could PM me the engineers manual for the Astec 63D please?

Thank you

Rafal1976

Hi KoolKid, I was wondering if you could PM me the engineers manual for the Astec 63D please?

Thank you

altor

Rafal1976 wrote: »

Hi KoolKid, I was wondering if you could PM me the engineers manual for the Astec 63D please?

Thank you

Whats the issue you are having?

KoolKid

Rafal1976 wrote: »

Hi KoolKid, I was wondering if you could PM me the engineers manual for the Astec 63D please?

Thank you

PMed you that manual. If you need any help come back to us.

marts

Hi.
I'm in bother also with my Aztec alarm.My telephone line is down atm and because I'm not with Eircom directly I may have to wait to get sorted. I have messaged my engineer but am awaiting a reply. However I'm fearful this is going to be beeping all night. Can any advice (simply please - I'm not very tech savvy) how I can bypass the dialer?
Thanks in advance

KoolKid

If it's beeping for line fault press clear and enter your code to silence it.

marts

KoolKid wrote: »

If it's beeping for line fault press clear and enter your code to silence it.

Sorry for delayed reply... I've been on to my engineer and he suggested that too however when I do that the alarm sets. Pressing clear alone silences the beeping temporarily and then it starts again after a few minutes. I have been on to my service provider and they say theres no fault in our area. It is strange though as it only happens during the day and not at night (Thank God!!) Anyway, I thought that I could find a way to bypass the dialer so that the alarm would still work if needed but that it just wouldn't ring me... It appears I can't according to the engineer.
Thanks for the reply.
Martina

KoolKid

Can you open the panel and tell me what connections are on the dialler. The first 4 terminals from the left hand side.

marts

KoolKid wrote: »

Can you open the panel and tell me what connections are on the dialler. The first 4 terminals from the left hand side.

I spoke too soon and put in a terrible night of the beeping almost every half hour..... Unfortunately I'm at work atm... I will be home tonight and will do as you asked and refer back...... Regards M