Manuals / Request a manual

Sent you that. Hope it helps.;)

furry87

New here cold I get the engineer/installers manual for hkc quantum 70.

Cheers

Thanks for the feedback. I do plan to change the battery but how do I stop the phone messages in the mean time. Also now the panel shows a "red" alarm and beeps every thirty minutes or so with a voice message about the battery. How do I stop this alarm until I can change the battery? It's driving me crazy.

Phil:)

PS: I think I recall that the phone connection runs inside the wall

Probably best to change the PiR battery anyway. (For a couple of reasons)
Can you see the phone line wired into the panel?

Thanks for the manual KoolKid that was real quick. It was the Quantum 70 that I was looking for. I have an immediate issue in that the alarm is calling my mobile every 10 minutes or so with a voice message to tell me that there is a low battery. The log shows that the hall IR sensor battery is low. I send the "0" confirmation back but the messages just keep on coming. How to I stop the messages.

Also I am curious as to how the alarm connects to my land-line, there is no cable from the alarm to the phone socket?

Regards
Phil:)

Hi, I would also very much appreciate a copy of the engineers user manual for the HKC 70 intruder alarm. Also is there such a thing as a default engineer access code?

Many thanks in advance.

Phil:)

Toby250 wrote: »

It was fault 92,i switched it off at the fuse box and back on again its fine now again but battery is flashing up on lcd ill order a new battery and get it fitted see will it stay going for an other few years.

That is an eeprom error. Down powering and powering back up if it brings it back on line you should be all good. The low battery needs to be replaced as soon as tho. This is more than likely what is pulling the system down.

It was fault 92,i switched it off at the fuse box and back on again its fine now again but battery is flashing up on lcd ill order a new battery and get it fitted see will it stay going for an other few years.

Muttley_666 wrote: »

Have one request, which will lead to another.

My hkc alarm (not sure what model) has recently stopped working as the batteries in the pirs went dead. While I have the batteries changed, I still have a comms fail error. I know I need to reset the pirs by using a walk-thru.

I think I need a manual to figure out where the routine is, but how do I find the model number from my alarm. The keypad is pretty standard.

Real newbie question, I know. :-)

You would need to know which system you have installed.
This thread is for requesting manuals so feel free to start a new thread.

Toby250 wrote: »

Got that thanks,I'd say it's on the way out,do you know of any direct replacement panel?

What fault codes do you have?
There are too many company's out there looking to upgrade than fix an Astec system.
In most cases the system can be repaired.

degsie wrote: »

Anybody have the installation guide for the attached SAB board? Its an old H.K.C board. Thanks

Its straight forward to add this to any system.
External bell + - to same in panel.
Strobe + - to internal bell in panel or else if you have engineer access you can set up an output as strobe.
BHO to BHO in panel.
Tamper return to tamper return in panel.

Muttley_666

Have one request, which will lead to another.

My hkc alarm (not sure what model) has recently stopped working as the batteries in the pirs went dead. While I have the batteries changed, I still have a comms fail error. I know I need to reset the pirs by using a walk-thru.

I think I need a manual to figure out where the routine is, but how do I find the model number from my alarm. The keypad is pretty standard.

Real newbie question, I know. :-)

Depends a lot on the wiring that's in place.
The GSD i70 is a combined unit. If the existing control panel is in a location away from the hall etc you would be fitting a separate PSU and housing the expander there.

KoolKid wrote: »

There's no direct replacement. GSD is the only one that is any way compatible.

Would much need changing to fit the GSD.. What would the cost be like? Thanks

I Pmed you that. Hope it helps.

HighFlyR

KoolKid wrote: »

A kind offer Tim.
I would say its best for people to request something & for the offer to follow.
I think the thread will be easier for a user to follow that way. Especially as it grows to a large number of pages.

By all means everyone feel free to link to any other manuals not listed above.

Hi I am new on here. Would you have a installers manual for scopetronic homeguard?

There's no direct replacement. GSD is the only one that is any way compatible.

KoolKid wrote: »

They are in the manual I have PMed you.

Got that thanks,I'd say it's on the way out,do you know of any direct replacement panel?

They are in the manual I have PMed you.

Would you have a list of fault codes for astec panels? Thanks

I PMed you the Europlex Manual.

I don't have anything in PDF on the HKC bell.
If you post a thread on what you need help with I'm sure we can get you sorted.

collywobbler

Hi,
Great and handy thread, Would anyone have a manual for a Europlex 3725-200P Intruder alarm system? I have found a basic User manual online but there is no fault codes/information in it,

cheers

degsie

Anybody have the installation guide for the attached SAB board? Its an old H.K.C board. Thanks

antonius1000 wrote: »

Hi
new to the board.
i'm looking for the engineers manual for a hkc quantum 70 alarm

i can see the user manual on the sticky thread(i have the user manual anyway) -so hope i haven't overlooked it.

thanks in advance
antonius

Sent you that by P.M.

antonius1000

Hi
new to the board.
i'm looking for the engineers manual for a hkc quantum 70 alarm

i can see the user manual on the sticky thread(i have the user manual anyway) -so hope i haven't overlooked it.

thanks in advance
antonius

PMed you that.

Bibrock

Hi

Would anyone have a copy of user and Engineer manual for Europlex Identifier panel please?

Many thanks