koolkid wrote: » To clarify. With a few exceptions, most bells do not have a battery. It's a capacitor. It is soldered to the PCB and not easily changeable.
positivenote wrote: » its defo the box on the wall outside guys. its been 'chirping' sporadically since we bought the house 4 yrs ago. a lad i know changed the battery (12v ?) on the box inside the airing cupboard as we where getting a warning it needed changing. this warning went when he changed the battery but the chirping returned a day or two later....
bryanbal wrote: » Just started to work on this panel. Basic question. How do i wire a dual end of line loop into a pir. i have 2 power wires and two alarm wires. two power ok. What combination do i use for the resistors and 2 wires at the pir with 4 screws with 2 alarm 2 tamper. Also is there a setting to have no eol for some zones. thanks
koolkid wrote: » I hope the attached image helps. Always best to use EOL over Non-EOL.
koolkid wrote: » There are different makes of these. Red/Yellow is usually the zone & Black/Blue is usually the tamper.
koolkid wrote: » Shouldn't be really.Have you a number of these prewired contacts going into the one junction?[/QUOT Just the one prewired contact. Just think it will be hard to hide all wires and resistors behind small contact. Also how do i wire from panel to hkc sabb?
bryanbal wrote: » Also how do i wire from panel to hkc sabb?
koolkid wrote: » LCS3 connects to STRB (Strobe) HC S1 connects to ext - (External Bell -) HC + connects to ext + (External Bell +) C connects to bho (Bell Hold Off) T connects to tamper return
bryanbal wrote: » Now For the phone line. The pstn fault clears if I have 2 wires going to top 2 screws or next 2.Which 2 should I wire cable into. Tried a manual test call ,doesn’t work. What settings do I need to check just to ring my own phone.
bryanbal wrote: » Ya thats the way i was doing it. For some reason the led pattern didnt change to correct pattern until i put the lid on. Also i only have one resistor in,the one that was already in the sabb. Is that correct? Thanks for quick replys. Il call it a day.
altor wrote: » Hi bryanbal, The A/R B/T is line in and AX/R1 BX/T1 is line out. The dialer on this panel is for contacting a monitoring station. You can get a voice dialer for the ATS its a AST7200.
bryanbal wrote: » need the AST7200 so. i had it ringing my phone continously but had no way to acknowledge the call and it was just silence with no announcement. that must be my problem.
bryanbal wrote: » it just seems like alot of connections and is messy.
altor wrote: » There is a junction box with a read fitted you can get, a lot less connections.
koolkid wrote: » These are the ones you want. Fully tampered as well.
altor wrote: » Yes, it will keep ringing until it gets an acknowledgement.
bryanbal wrote: » Ftc fault comes up alot. even when i clear it it comes back on next alarm.Can i disable this until i get voice module. Seems to only clear when i power down the panel.
bryanbal wrote: » Dgp setup. I have registered a few devices and have tested them for alarm and tamper in dgp menu. HOWEVER THEY ARE NOT IN MY LIST OF ZONES TO TEST IN WALKTEST MENU. Will this be solved if i go to zones menu and add zones. Once i have them registered in dgp, is that generally all i need to do in that menu and just treat them like a regular zone and do the rest of the programming through the zone menu.
hello932 wrote: » Where can i find decent info to replace a eircom phone watch alarm with a stand alone alarm that is monitored (but not by eircom)?
