Anybody?
...
Freeview is Uk via aerial and no
FTA or Freesat on sat 28.2
Saorview is on Irl by aerial
A box like Zgemma H7S 2 x sat tuner and 1 Terrestrial tuner will give you both with tuner feeds.
Hi, haven't read whole thread.
I want to get saorview and freeview UK channels on one box. Is this the way to go?
Is it hard to set up and what do I need?
Leave your non working tuner one as disabled.
Might need to recheck your F connector is tight with units powered off and the centre core not touching the side.
Did scan on my octagon. All channels reappeared (again it's rarely used). Still nothing on zgemma. I'm going to bell cable tomorrow to see if it's OK. May be damaged in attic. Don't know how but hoping it's that simple. Can you send pic of zgemma satellite setting to make sure I'm correct.
When was the last time you scanned the sat as channels did move .
These are the settings for the tuners.
Tuner A.
Simple,
Single.
28.3e.
No
Tuner B.
Disabled.
Tuner C Terrestrial .
Working.
Hi, 2 feeds that are not sky related are connected to receivers. One is my zgemma and the other is connected to an old octagon. Turned it on yesterday and got channel 4 and itv. Box wasn't turned on in ages so no bbc, still picking up channels. Zgemma picking up nothing.
I've it connected to the right satellite. Other settings are what I usually pick.
I would be checking if you had other feeds NON SKY Q to check tuners on.
These feeds were they connected on a Q box as need to be changed on lnb to universal side.
Loose F connectors on lnb?
No blockages of line of sight like trees or buildings.
Make sure you have astra 28.2 for sat tuners selected?
Hi, purchased this from world of satellite, triple tuner. 2 x satellite, 1 x terrestrial. Can't get UK fta channels working. Have saorview working grand. Not sure what's going on. I had an old gigablue receiver that worked on the same feed. I decided to reboot that to a newer image. After I flashed it I couldn't pick up any UK channels,thinking gigablue was fecked I got this zgemma. This is doing the same. Came preloaded with openvix from world of satellite. It's coming from Sky hybrid lnb model EL02B. Anyone any ideas. I think lnb should be ok but would newer openvix bring issues with this lnb type. Any help appreciated.
Anybody else having trouble with ITV1? There is terrible interference on this channel only. All the other channels are fine. This is night and day making it unwatchable.
I have the older h2s version and as stated above by greasepalm the port is behind a flip down flap on the front. With mine its just plug and play.
Think there is a front flap on front with usb port there , plug in usb and unsure if media scanner or Picture will open it.
Look in you plugins .
Does anyone know if you can watch media files from a USB flash drive on the Zgemma? If so, where on it would I find it? Do I need to download anything?
I bit the bullet and everything went OK, and it restored all my settings from my 6.3 backup. The only snag, and this happens, every time I flash a new release, is that normally my box is connected via WiFi for which I need a driver that isn't included in the image and therefore requires a plugin. As plugins are not restored, but downloaded afresh when upgrading, I need to connect via a LAN cable to do the restore. Luckily I have an unused powerline adapter I can use temporarily for that.
In any case, you can always flash it into an unused partition, so that you can easily go back to the old version if necessary.
Yes i saw it and not too much in a hurry as one person had a backup , reflashed box and their settings and stuff vanished.
BTW a new OpenVIX version was just released, 6.4.001.
That's the impression I got from reading some of the replies to similar questions on the openvix forums where the devs wash their hands of it. So why bother including it if it's known not to work?
Never got kodi to work on any boxes and people are told to use an android for kodi
Out of interest, has anyone got Kodi to work on their Zgemma H7S? It installs fine and starts up but then just crashes shortly afterwards.
Got it sorted. Thanks for your interest.
I don't know anything about plugins. I don't have an internet connection if that's relevant. EPG is saved to HDD.
What plugin are you using for your EPG , does your box run on an old image i wonder.
Epg getting saved to Hdd or Usb.
Sorry to butt in here. My EPG has no programme information. How do I get it to show programme info?
I never to tried to move channels, but my curiosity got the better of me and I figured it out.
This is how I did it.
Press TV button on remote control
Select all channels
Press Menu on remote control
Select Enable Move Mode
Scroll down to the channel you want to move (you can use the side arrows on your remote control to move up and down quicker)
When you get to the channel you want to move press OK on remote control
The channel will then turn RED
Then to move it to where you want to place it, use the using the side arrows on your remote control to move up and down
When you have it where you want to place it, press OK and the channel will go back from Red to White.
Do this with all the channels you want to move.
When you are happy with your selection and order
Press Menu and disable Move Mode
Then press Exit on your remote controll and the new channel list will be saved.
Print this and go step by step and you should be OK.
Best of luck
Socks
Okay thanks Ill try that this week.
All enigma 2 boxes with different names do the same thing .
One needs a good 8gb usb stick max size , Kingston , Cruzer , Integral , San disk.
Images downloaded are in zip format and need to be extracted first.
Link to manually download the most recent version of OpenVix for the Zgemma H7S. (Make sure to match model numbers)
Link to instructions how to flash this image using a USB (again watch for correct model)
https://www.openvix.co.uk/index.php/guides-and-tutorials/receiver-usb-flashing-guides/zgemma-usb-flashing-guides/
Once you flash the new image, a wizard will guide you through the initial setup for network and tuning etc.
