twist rates

badshot · 30-05-2020 11:09pm #1

buying a 223
whats the difference between a 1/12 twist and a1/8 twist

alanmc · 30-05-2020 11:49pm

12" inch twist will stabilise the shorter bullets. Typically up to 55gr. 8" twist can stabilise those longer ones (tend to be heavier) 69g, 77g etc. I used to shoot some 69g SMK Fiocchi in my Tikka T3 8" twist and they were great.

Most ammo on the shelf is 55g and less. You sometimes see 64g and Lakelands has a buncb of 69g.

If you're only going to shoot the lighter faster stuff, 12" is more than sufficient. If you think you might want to shoot the heavier (read longer) bullets, then go for the 8" or faster twist.

My current 223 is a 9" twist. Shoots pretty much everything up to 69g really well. Anything above that though, tends not to stabilise too well.

PSXDupe · 31-05-2020 12:47am

I am in the exact same position. Decided a couple of weeks ago to buy a .223 and like you need to understand twist rates.

After reading many articles and advice from many people. This is what I have come up with.

1:12 twist, will shoot 55gr rounds really good, up to 69gr, some rifle have trouble with 69g, but 63gr not issue.

A 1:12 will also shoot lighter rounds, 50gr, some lighter loads, but you don't seem too many here in Ireland.

Now, 1:8 twist will shoot 55gr no problem, and with a good round will shoot as good as the 1:12. Where the fast twist comes into play is with heavier loads. The 1:8 will shoot rounds up into the 80s.

So the fast twist is more flexible, but some rifles will not shoot round below 55gr.

I have a Tikka T3x .223 1:8 twist ordered. (Some people have said this rifle will even shoot 50gr)

freddieot · 31-05-2020 8:28am

Really good advice. My understanding is that the length of the barrel is also part of the equation for working out the best option (i.e. 1/8 in a 20in is a different beast than 1/8 in a 28in. Maybe someone can explain in more detail.

I remember seeing some sort of formula a few years ago for working out ammo v twist v length etc..

Cass · 31-05-2020 2:01pm

When discussing twist rates and suitable ammo choice we talk of bullet weight, but the weight of a bullet is somewhat misleading. What we actually need to know is the bearing surface length.

Every calibre is fixed. Meaning a 40 gr bullet and 75 gr bullet in 223 have the same diameter. To make it heavier they make it longer. This is when twist rate comes into play. The longer a bullet the more bearing surface that engages the lands and grooves. The bearing surface of each bullet can vary with some "lighter bullets" having a longer bearing surface than other bullets in the same weight category. This means if you have (made up example) a 55 gr Hornady and 55gr Federal bullet well both can weigh the same but the Hornady may have a shorter bearing surface than the Federal so it'll act like a lighter bullet and work in a slower twist rate than its recommended one.

This picture (excuse the microsoft paint drawing) the difference between a 40gr bullet and 75 gr bullet.

6034073

However if i were to talk to someone about suitable bullet for twist rate in terms of bearing surface i'd be talking in thousandths of an inch. For example (and excuse the numbers they are completely made up because i don't have the actual numbers) a 40 gr would not be a 40 gr but a 0.4721 bullet compared to the 0.5512 bullet (75 gr).

It's easier to talk in weights.

The reason i say weight is not ideal is because sometimes this weight to bearing surface is not always as predictable as you'd think. I'll discuss this in 308 as i know them. My rifle is 1:10 twist. It's suitable for bullets of 168 - 185 gr. They have longer bearing surfaces than 123 - 155 gr bullets so work better in the faster twist rate.

However the Lapua Scenar 155 gr is a long bullet. So long in fact that it's bearing surface length is the same as the 175 gr Sierra, and close to the 180 gr bullet. Because of this the bearing surface is longer, and the "lighter" bullet acts more like a "heavy" bullet. This means that although it's a 155 gr bullet it works, quite well, in a 1:10 twist.

It's for this reason that some rifles will shoot heavy or light bullets that seem to contradict the twist rate:bullet weight ratio. This is because of bearing surface length. Example of this oddity below:

6034073

Feisar · 31-05-2020 10:29pm

freddieot wrote: »

Really good advice. My understanding is that the length of the barrel is also part of the equation for working out the best option (i.e. 1/8 in a 20in is a different beast than 1/8 in a 28in. Maybe someone can explain in more detail.

I remember seeing some sort of formula a few years ago for working out ammo v twist v length etc..

Greenhill formula, when I googled it to check, I came across the Miller Twist Rule

https://en.wikipedia.org/wiki/Miller_twist_rule

TheEngineer1 · 31-05-2020 10:36pm

Out of curiosity for a .223, why bother making a 1:12 twist barrel at all? Why don't all manufacturers make all their rifles in 1:8?

Cass · 31-05-2020 10:44pm

Because the most commonly used ammo seems to be in the 40 to 55gr mark which is ideally suited to a 1:12 twist rate.

1:8 twist rate is only suitable for ammo in the 69gr plus range.

zeissman · 31-05-2020 10:44pm

TheEngineer1 wrote: »

Out of curiosity for a .223, why bother making a 1:12 twist barrel at all? Why don't all manufacturers make all their rifles in 1:8?

If you want to shoot the lighter bullets a 1/12 twist is the best choice..
Some 1/8 twist rifles will shoot the lighter bullets but some wont.
My mate has a tikka that is very accurate with the heavier bullets but not so with the lighter stuff.

Feisar · 31-05-2020 10:47pm

TheEngineer1 wrote: »

Out of curiosity for a .223, why bother making a 1:12 twist barrel at all? Why don't all manufacturers make all their rifles in 1:8?

Apparently a 1:8 gives up some velocity with the lighter bullets. A 1:12 is optimum for varminting as it maximizes a 40 to 55 grain bullets velocity.

Edit - I'm quoting textbook knowledge, I haven't shot the same rounds side by side in a 1:8 vs 1:12

Cass · 31-05-2020 11:51pm

Its also about stability in flight. The wrong bullet with the wrong twist rate rifle will cause instability in flight and result in loss of accuracy or keyholing.

alanmc · 01-06-2020 12:23am

I find the Berger Twist Rate Calculator really useful. It has presets for Berger bullets obviously, but you can get specs from other bullet manufacturers (Sierra, Hornady, Barnes, Lapua, etc) from their websites and input parameters (length, Ballistic Coefficient) along with the twist rate of your barrel to produce a natty graph which tells you how stable your combination is.
I wouldn't use it as gospel - it's not a replacement for actually trying a bullet in your rifle, but it's a good guide.

alanmc · 01-06-2020 12:43am

TheEngineer1 wrote: »

Out of curiosity for a .223, why bother making a 1:12 twist barrel at all? Why don't all manufacturers make all their rifles in 1:8?

I've kinda wondered this myself. Mainly when I'm trying to figure out why my .308 barrel is a 12" and not a 10" twist. If you google enough, you'll find holy wars about "over stabilisation". There are "stories" and myths about bullets flying apart due to being over spun. Many refute this and yet many swear it's true. I remain unconvinced.
There are so many variables in play here, not just twist rate (velocity - a function of barrel length, charge weight and powder burn rate, bullet shape - as Cass has explained above, barrel construction and rifling type - button vs cut vs polygonal).

All of these variables contribute to the revolutions per second on the bullet when it leaves the barrel. IMO, there is no substitute to trying bullets in your rifle. The weight vs twist is a good guide, but not always the truth. For instance, my 12" twist .308 barrel on paper shouldn't stabilise a 175g TMK bullet .... but it does.

Mellor · 01-06-2020 9:46am

freddieot wrote: »

Really good advice. My understanding is that the length of the barrel is also part of the equation for working out the best option (i.e. 1/8 in a 20in is a different beast than 1/8 in a 28in. Maybe someone can explain in more detail.

The rate is the same, so the rotational force is the same. But the longer barrel has that force acting on it for longer, so generates a more spin.

1:8 in a 20" barrel is 2.5 revolutions.
1:10 in a 25" barrel is 2.5 revolutions.
1:12 in a 30" barrel is 2.5 revolutions.

All thing being equal, the three barells above would produce the same amount of muzzle spin, and this stabilize to the same degree. It's actually the number of revolutions that is relevant rather than the twist rate.

clivej · 01-06-2020 11:17am

Mellor wrote: »

The rate is the same, so the rotational force is the same. But the longer barrel has that force acting on it for longer, so generates a more spin.

1:8 in a 20" barrel is 2.5 revolutions.
1:10 in a 25" barrel is 2.5 revolutions.
1:12 in a 30" barrel is 2.5 revolutions.

All thing being equal, the three barells above would produce the same amount of muzzle spin, and this stabilize to the same degree. It's actually the number of revolutions that is relevant rather than the twist rate.

Nothing to do with barrel length. 1in12 means the bullet rotates once in every 12". This equates to, when the bullet leaves the muzzel and travels 12" it has rotated once.
A 1in 8 has rotated once in 8" therefore it has more spin, it has more giroscopic effect and more stability

Mellor · 01-06-2020 1:16pm

clivej wrote: »

Nothing to do with barrel length. 1in12 means the bullet rotates once in every 12". This equates to, when the bullet leaves the muzzel and travels 12" it has rotated once.
A 1in 8 has rotated once in 8" therefore it has more spin, it has more giroscopic effect and more stability

I think I didn't explain what I meant very well.
I understand that the twist is the rate of rotation of the rifling. 1:10 is same rate regardless of length, therefore the torque is constant being a product of the rate.
Referring to length I meant the bullet is under the influence of the torque for longer. I've always understood that to mean more spin in RPM.

Eg, Take a 22 rifle and a 22 pistol (in the same twist rate). During flight the rifle round will spin faster in terms of RPM. Although come to think of it, that would be mainly a product of increase muzzle velocity I suppose.

yubabill · 02-06-2020 7:42am

Cass wrote: »

Because the most commonly used ammo seems to be in the 40 to 55gr mark which is ideally suited to a 1:12 twist rate.

1:8 twist rate is only suitable for ammo in the 69gr plus range.

For a long time I was recommending 55gr and above for 1:8 twist barrels and was following that myself.

Then Tack and a few others here were saying they were getting accuracy with 40gr BT's and for a while I was sceptical.

Then I got 3 or 4 45gr Remy JHP's and tried them for pig iron - they were all touching at 50yds.

I bought some 50gr Fiocchi HP's and they're giving me an inch or less at 100yds consistently and I do note that other people have had different experiences with them, but the two boxes I bought have been trouble-free.

I don't know exactly why manufacturers offer a choice between 1:12 and 1:8, maybe the slower twist gives better accuracy with loads of 55gr and less? never got the chance to try that out.

The AR15 was first issued with 1:12 twist for the US 55grFMJ, but were retrofitted with 1:8 when NATO standardised to the 62gr (SS109? can't remember exactly the designation). Maybe that has something to do with it, a kind of tradition thing, but I suspect the reason has more to do with precision.

Maybe some range shooters have compared like-with-like? Say 2 T3's?

Feisar · 02-06-2020 9:40am

alanmc wrote: »

I've kinda wondered this myself. Mainly when I'm trying to figure out why my .308 barrel is a 12" and not a 10" twist. If you google enough, you'll find holy wars about "over stabilisation". There are "stories" and myths about bullets flying apart due to being over spun. Many refute this and yet many swear it's true. I remain unconvinced.
There are so many variables in play here, not just twist rate (velocity - a function of barrel length, charge weight and powder burn rate, bullet shape - as Cass has explained above, barrel construction and rifling type - button vs cut vs polygonal).

All of these variables contribute to the revolutions per second on the bullet when it leaves the barrel. IMO, there is no substitute to trying bullets in your rifle. The weight vs twist is a good guide, but not always the truth. For instance, my 12" twist .308 barrel on paper shouldn't stabilise a 175g TMK bullet .... but it does.

I read about bullets ripping themselves apart as well from to much rpm. I don't recall exactly however it was in reference to fast .22s and light jacketed varminting bullets.

clivej · 02-06-2020 10:25am

I got the best ever groups with Hornady 40gr VMax from my CZ varmint 223 1in8 twist. 1 x 28mm 3 shot group and 2 x 40mm 3 shot groups at 300m

yubabill · 02-06-2020 11:20am

Just for the record, to date the best grouping I get from my T3 1:8 is with hornady 55gr Steel Match FMJ - around 0.5inch at 100 yds.

Never tried the 40gr BT's - too rich for my blood - but the 55gr BT's give me around 1 inch at 100 yds (still have some I bought years ago at 25.00 per box).

I just shoot whatever is cheap and reliable and keep the good stuff as ornaments.

badshot · 03-06-2020 3:10pm

any harm asking which model tikka
and where did you order it
can't decide myself between varmint supervarmint or tactical

zeissman · 03-06-2020 5:44pm

badshot wrote: »

any harm asking which model tikka
and where did you order it
can't decide myself between varmint supervarmint or tactical

My choice would be the supervarmint.
It costs a bit more than the varmint but I think it's worth it for the adjustable stock and picatinny rail.
The tactical is also a nice rifle but is more expensive.
I would prefer a stainless rifle

Uinseann_16 · 04-06-2020 4:47pm

yubabill wrote: »

For a long time I was recommending 55gr and above for 1:8 twist barrels and was following that myself.

Then Tack and a few others here were saying they were getting accuracy with 40gr BT's and for a while I was sceptical.

Then I got 3 or 4 45gr Remy JHP's and tried them for pig iron - they were all touching at 50yds.

I bought some 50gr Fiocchi HP's and they're giving me an inch or less at 100yds consistently and I do note that other people have had different experiences with them, but the two boxes I bought have been trouble-free.

I don't know exactly why manufacturers offer a choice between 1:12 and 1:8, maybe the slower twist gives better accuracy with loads of 55gr and less? never got the chance to try that out.

The AR15 was first issued with 1:12 twist for the US 55grFMJ, but were retrofitted with 1:8 when NATO standardised to the 62gr (SS109? can't remember exactly the designation). Maybe that has something to do with it, a kind of tradition thing, but I suspect the reason has more to do with precision.

Maybe some range shooters have compared like-with-like? Say 2 T3's?

Just a tiny thing there the AR-15 was never issued as a main service weapon the M16 was adopted as a service weapon
The AR-15 is a semi auto only civillian rifle
The colt 601, M16, M4 are select fire which are versions of the AR-15 but they are not AR-15s
Basically AR-15s are civvi rifles with no happy switch

But more to your point the original M16a1 was issued with a 1 in 12 twist rate some of the really early rifles had a 1 in 14 twist (the .222 twist rate from which the .223 was developed) they standard round at the time was the 55gr
When NATOs SS109 62gr came out there were issues with the 1 in 12 twist so they changed over to a 1 in 7 twist as theyre were apparently key-holing issues along with accuracy problems etc with the old 1 in 12 barrels

Shooting Forum - Firearms licencing information

twist rates

Comments

Forum Charter - Useful Information - Photo thread: Hardware - Ranges by County - Hunting Laws/Important threads - Upcoming Events - RFDs by County

Forum Charter - Useful Information - Photo thread: Hardware - Ranges by County - Hunting Laws/Important threads - Upcoming Events - RFDs by County

Forum Charter - Useful Information - Photo thread: Hardware - Ranges by County - Hunting Laws/Important threads - Upcoming Events - RFDs by County