Solar Panel Project For School

bungaro79 · 01-04-2022 11:21pm #1

Hi

I am after getting a few solar panel kits (https://irishelectronics.ie/epages/950018241.sf/en_IE/?ObjectPath=/Shops/950018241/Products/EDU02) to teach the basics of circuits and renewable energy with my 5th class students. We also usually do a robotics competition every year and we use a 7.2v battery (https://www.sgeducation.ie/product/vex-iq-robot-battery) in this and I'm thinking about linking the two by setting up a solar panel to charge it. I thought getting a cheap wind turbine might be an option but after reading a few threads on here have put me off. I'm going to try and get some sponsorship locally and get set up using a basic solar panel system.

So, I need to go from the solar panels to something I can plug the battery charger (https://www.vexrobotics.com/chargers.html) into to power the robot. I've read a lot of the threads on here and I'm hoping that this might be a bit simpler than what you'd need in a house so if anyone can advise me on what I'd need to get or any place to get these basics it would be much appreciated.

the_amazing_raisin · 01-04-2022 11:47pm

First thing, I love this idea, you could have the solar panels recharging the batteries when the robots aren't being used

A little solar robot carport would be awesome 😁

This interesting thing is that the battery charger you showed is that it takes an AC input from the looks of it. There's no spec sheet on the site so it's hard to tell, but looking at the power cords they're including I would expect a brick to convert the AC from the socket to DC if the charger accepted a DC input

This is the root of the issue, to use that charger you'll need to convert the DC from the solar panel to 230V AC and then the charger will convert this back to DC to charge the battery

As you can imagine, this is a bit overly complex, and also dangerous as you don't want to be messing around with 230V AC

Ideally, you could find a small solar panel outputting a bit over 7.2V and connect this to a charge controller for your 7.2V battery. It would be a much simpler setup overall

bungaro79 · 04-04-2022 9:26am

Great stuff, thanks for that reply! I just googled "charge controller" there. So am I right in thinking the wire from the solar panel goes into that and then its a case of finding one with the output port I'd need to connect it to my battery?

10-10-20 · 04-04-2022 10:08am

I like the idea of a solar car-port idea... but keeping away from AC voltages... What about a solar car-port with "power-wall" concept where the solar charges a static battery pack ("power-wall") in the car-port and the vex robot has to detect when it's battery is low and return to the car-port to take a charge?

So you would effectively go:

Solar panel (~18v) -> solar charge-controller -> 11.1v (3x 3.7v Li-ion battery-pack).

The reason I selected 3x 3.7v is that it will give you a working voltage of around 12v which is much easier to obtain charging parts for - such as 12v USB adaptors. Between 6v to 7v v tends to be around the cut-off voltage for many 12v adaptors giving you very little working range.

Then the charger for the robot (also located in the car-port) could use a buck-converter (DC to DC converter) to step the ~12v down to a level appropriate for the robot's battery (that is assuming that the robot has a charge-controller onboard). I've used this adjustable buck converter from a guy in Ennis as it's got great efficiency: MP1584EN

Otherwise if you need a charge-controller you can go from 12v (power-wall) to a 5v USB connector and into a charge-controller such as this: https://makershop.ie/Electronics/Power/TP4056-type-C

Anyway this all depends on the charging methods and voltages available. Don't forget that Li-ion isn't your common-or-garden AA or eve C or D cell, the battery resistance of a Li-ion is much smaller and they don't appreciate being shorted!

the_amazing_raisin · 04-04-2022 10:15am

Well you could have 2 batteries for each robot and the solar panel charges one while the other is in use. Might be the simplest solution

the_amazing_raisin · 04-04-2022 10:20am

https://www.boards.ie/discussion/comment/118877360#Comment_118877360

Yeah the charge controller converts whatever voltage and current from the panel to the required voltage for the battery. Ideally you'd have something you can just connect directly to the battery cradle to charge the battery. Not sure how easy that will be to find, that Vex battery looks kinda specialised, like a digital camera battery

Ubbquittious · 04-04-2022 10:51am

you could 3d print a holder for that battery & charge using programmable charge controller. would save a lot of messing with ac/dc converters.

10-10-20 · 04-04-2022 12:50pm

I'll also add that this site is a fantastic resource and you (as a teacher) can use it as a source for lots of the learning. Even just graphing how batteries discharge along a curve makes understanding easier.

https://batteryuniversity.com/article/bu-409-charging-lithium-ion

bungaro79 · 04-04-2022 5:23pm

Really appreciate the comments on here. 10-10-20, I think that what you mentioned above regarding the power wall is a great idea. The plan is to look at all the suggestions above and try and teach myself (with a bit of help from another teacher who used to be an electrician!) how to best set this up. We have a 3d printer in the class too so I can use that to make whatever casing is needed.

Its good to learn about the batteries from the above link too as I'd love to get the lads to make something like a phone charger that they could use in class but I'll start with the robot battery first!

10-10-20 · 04-04-2022 8:37pm

I can't take the credit - lots of good ideas and people with input on here.

bungaro79 · 07-04-2022 8:35pm

So, I'm after buying a few solar panels and plan to experiment around with them over the Easter break. I saw this inverter (https://www.amazon.co.uk/KRI%C3%8BGER-Inverter-Refrigerators-Microwaves-Chainsaws/dp/B07S37S1ZM/ref=sr_1_32?keywords=solar%2Binverter&qid=1649359429&sprefix=solar%2Bin%2Caps%2C136&sr=8-32&th=1) on Amazon. I still plan to try and play around with above suggestions but for now could I do something as basic as hook up the solar panels to this to charge it up and then plug in my battery charger to it?

Update:

I'm after watching a few videos on Youtube there (namely this one https://www.youtube.com/watch?v=HOka91PxFlA) and its saying I need a solar charge controller so I can't just hook the inverter up to the panel, right? Can someone explain why the charge controller charges the battery but then it loops back and goes to the inverter?? You can't just hook the inverter to the battery?

bungaro79 · 27-04-2022 7:08pm

So, I've been doing a lot of research and am slightly more clued in to what I'm hoping to do! I found a really good book on Amazon (https://www.amazon.co.uk/gp/product/1546567119/ref=ppx_yo_dt_b_asin_title_o05_s00?ie=UTF8&psc=1) by a guy who has loads of videos online.

The set up I hope to use is a 100W solar panel which will be fed into a solar charge controller (an MPPT 75/10, very kindly donated by an Irish company offgridkit.ie) and this will charge a deep cycle battery I bought locally (12V 34 Ah). I have a 500W inverter (and I'm hoping to get a 1000W pure sine one) which I will use to charge my robot battery.

There's one bit though that I'm still unsure of after reading the book. It seems to be pretty straight forward with most of the connections but he does mention that the wire between the battery and the inverter will take the most amps and therefore needs to be really big. For a 500W inverter he said to use a 10 gauge wire and if you're using a 1000W one then you'd need a 4 gauge wire. A neighbour, who is an electrician, came over to look at my plans but when we converted the wire sizes (https://www.lapptannehill.com/resources/technical-information/metric-to-awg-conversion-chart) he couldn't believe the size that would be needed! He did say that he doesn't really deal in DC connections so I'm hoping someone on here might point out if something above is wrong!

10-10-20 · 28-04-2022 9:23am

Not being negative and not wanting to pull you up on this as I'm sure you have the safety of the students in mind, but is mixing mains voltage and secondary level student projects safe? I'm in two minds about whether it is or not, but you're the best judge. Bear in mind that these inverters have poor or no safety devices and aren't inherently safe just by virtue of their dual 110v sources. They don't have RCD's and absolutely cannot be earthed (unless specifically designed to be).

4-gauge is 5.2mm diameter or 21.1mm^2 and 1000W at 12v DC = 83A. That's hefty stuff alright, but if you're really aiming to pull anything near the rated power of the inverter, then you need to go for it to reduce the losses in the wire alone. You should be able to source that spec of wire in a motor-factors, or else they'll tell you where to get it. Don't buy it off ebay or other similar vendors, it tends to be sold as copper but can be aluminium instead (AL burns over a lighter flame, CU doesn't).

Anyway, back to basics: why do you want an inverter? Bear in mind that if you're charging a battery off a battery, the worst plan is to convert that lovely stable 12v DC into 220v AC mains through an inverter just to convert it back into DC at some other low voltage. The efficiency losses for each step are approx 20% and all of the lost power just goes off as heat. Maybe that's actually a good equation for the students to measure and calculate and understand, but otherwise it can be avoided by just converting the 12v into the required battery voltage by using a DC-DC charger. Can you source a suitable 12v or 24v charger instead?

Come back with questions and ideas, happy to help.

bungaro79 · 28-04-2022 9:42am

Thanks 10-10-20. Really great advice on there. You're absolutely right about the safety issue. This will be worked on at home and I've 3 electricans who I'll be showing the finished system before it comes into school. If there's any issue from any of them then I won't be risking it. The inverter won't be pulling any hectic amp numbers but I'll look into this more but good tip about the motor factors for these.

Your last point is what I was hoping to work on after this. I am pretty much going off the book I bought and it is more about running off an inverter but I had seen the DC-DC charger and had planned to work on this after. The only issue with the robot battery I'm planning to charge is that it isn't a standard size and it has to be slid into a charger to work. If there are any DC-DC chargers or places with info on them I'd love to hear it!

10-10-20 · 28-04-2022 11:06am

So what type is the robot battery? Do you have a part-number and link? Maybe they have their own DC-input charger.

bungaro79 · 28-04-2022 12:38pm

Not sure to be honest. You'll see yourself from the links below that its a connection point rather than a port. It would be great if there was something there I could use directly!

Battery

https://www.vexrobotics.com/228-2604.html

Charger

https://www.vexrobotics.com/chargers.html

10-10-20 · 28-04-2022 2:20pm

Ah VEX. You linked to that above, but I didn't realise that you were using it.

So that's a 7.2v 2AH battery made up of 6x 1.2v (NiMH - link to battery university) cells in series, with a positive and negative pads and what is probably a charge status (??) connection in the middle. Can you put a multimeter across the terminals and measure the voltage from (-) to the middle connector of the battery? I'm guessing that the battery might have a charge controller within it and potentially that middle pad is the status output for the LED on the charger and there may be no voltage present on it when you read it.

Li-ION batteries often have a middle pin/connector, but that's used for balancing individual or pairs of cells during charge - but with 6 cells in series in an NiMH pack like that - maybe I'm wrong but I'd hardly think that there would be much point in using balancing at the middle point.

If you have a dead pack, open the casing slightly and see whether there is a small circuit in the battery pack (I'm talking about opening the plastic casing, not touching the battery cells).

Anyway, please check what voltage is read between (-) and the small middle pad and if it's coming back as 0v then you could try get a NiMH 7.2v portable/vehicle charger and try a test-charge on a empty battery to see if it takes it (come back to us here before you take that step though).

bungaro79 · 28-04-2022 7:04pm

I'll check that tomorrow as all the stuff is in school. Pretty sure there is one battery pack which is totally dead so I could take that apart and post a photo on here. I just had a quick search for the charger you mentioned above (https://www.amazon.co.uk/7-2v-battery-charger/s?k=7.2v+battery+charger). Which type of those chargers were you thinking? And is this so I could possibly use a DC-DC charger to go directly and not have to use the inverter?

Thanks again for all the replies

bungaro79 · 29-04-2022 2:59pm

bungaro79 · 29-04-2022 2:59pm

Just took these, hope it's what you were looking for!

10-10-20 · 29-04-2022 4:42pm

Yeah, so I was doing a bit of digging... ;)

Turns out that the middle pin is used by the charger to identify the battery, and that's why you see no voltage from it. But - from what I can understand - the battery isn't locked to the charger, and that means that our plan to use a DC charger still holds some water.

The theory behind it is that a completely flat battery which is too flat for the charger to recognise will just give a red LED on the charger. But these flat batteries can be recovered using a manual process and these IQ brain systems. To recover the flat battery you connect it up to an IQ brain and connect a motor to one of the ports of the brain and use the motor to generate a small amount of power which is fed back into the battery. After about a min of twisting the motor to charge the battery like this on the IQ, if you then move the battery over to the charger, it should hopefully see the battery and start charging it.

Anyway, the point is that if you can do that with with a simple motor, there should be little stopping you from charging the battery from a standard 7.2v NiMH DC-input charger... that is if you can find one!

I'll search out a charger over the coming days, but they appeared elusive during my first search.

randomname2005 · 29-04-2022 4:54pm

Great idea and super feedback from others. Mostly replying to keep track of this!

bungaro79 · 29-04-2022 5:05pm

https://www.boards.ie/discussion/comment/118994117#Comment_118994117

I actually found a video on how to jump the battery a few years back! It saved me a lot of cash as I didn't have to replace them when we returned in September to find them all dead!

Thanks a million for looking out for the charger for me. To be honest I still am kinda wondering what it will actually look like!

10-10-20 · 29-04-2022 6:18pm

This is one type:

https://www.rccontrolfreak.co.uk/72V_USB_Charger_Tamiya_Connector_Plug_NiMH_NiCD_RC_Model_Battery/p23800_18709054.aspx

Looking for one which converts from 12v (or 12/24v) to 7.2v...

bungaro79 · 06-05-2022 10:02am

Just waiting on my 100w solar panel (these ones are only 10w) to get started!

The Continental Op · 06-05-2022 10:07am

Why not use some of the power once you have your 100W panel to power a Raspberry Pi web server and host the notes for the solar project?

Doesn't need to be on the web just a class WiFi access although that might disadvantage any child without a smartphone.

bungaro79 · 20-05-2022 8:44pm

Still waiting on the 100w solar panels 😬

The direct sun is gone here in Cork but I'm hoping to test this out properly tomorrow. I got a DC-DC converter 12v to 5v today so does this set up look ok? The panel is a 12v 10w. Hoping to try out a phone charger or power bank on it in the sunshine tomorrow 🤞

The Continental Op · 20-05-2022 10:53pm

That one is on my Amazon wish list https://www.amazon.co.uk/Power-Module-DC-DC-Supply-Converter/dp/B071ZRXKJY/ along with a hundred other bits for ideas for projects.

I looked up doing something similar on a much larger scale recently and the answer was to use a buck converter so technically that should work. I think it just depends on getting more that 7.8 Volts from the solar panel which is the minimum for that unit to work.

10-10-20 · 21-05-2022 11:30am

That 12v to 5v board looks like this one here:

https://www.amazon.de/-/en/Buck-Converter-Module-Voltage-Regulator/dp/B09NVZ6Y6J/ref%3Dsr_1_15

That's a buck converter alright and it has a pretty good input range of DC 9V--36V. So yeah, ideal for your needs as long as the 100w panel sits around 15v or so.

Just in terms of wiring - don't skimp on good quality wire when you're working with higher loads later on. Consider using mains cable if you don't have 2.5mm^2 red and black (but label it up very well).

The other think that you can do is get one of these USB testers - it will allow you to watch the cumulative energy put into a device/battery. Very educational!

https://www.amazon.de/USB-3-0-Tester-Multimeter-3-7/dp/B07THZFDGH/ref%3Dsr_1_3_sspa

Finally, if you get yourself a variable USB load tester (or just a selection of big resistors), you can test the performance of the power converter.

https://www.amazon.de/-/en/Resistor-Adjustable-Constant-Electronic-Capacity/dp/B07WP1FP82/ref%3Dsr_1_9

Here are some 12v to 5v supplies which I was messing with. The worst obviously was a "Benq" branded board which was so bad that the output voltage dropped to 4.2v at 1A (it was rated for 3.5A, so clearly a failure).

The Anker PowerDrive was a common USB car-charger, quite impressive.

Anyhow, all food for thought!

bungaro79 · 21-05-2022 10:42pm

Thanks for the replies. Unfortunately the above set up didn't work today. I had the 1 10W 12V in direct sunshine and then used the same wire set up (crocodile clips onto the wires from the panel and onto small wires which fit into the buck converter). I plugged in my phone and then my power bank but it didn't seem to work for some reason.

Those links are great. I had actually seen the USB tester on Amazon already and thought it might be useful so I'm glad to see the recommendation!!

10-10-20 · 23-05-2022 2:52pm

https://www.boards.ie/discussion/comment/119095514#Comment_119095514

That might have been the phone if the power quality wasn't good enough. You'll need to measure some of the voltages/currents while it's setup to see if it's working properly.

Measure the panel voltage when open-circuit (no devices) and in full sun (preferably not behind glass).
Connect up the converter module and re-measure the voltage (should be roughly the same).
Put a load on the output of the converter - something between 33 and 80-ohm resistor (for a load of between 63mA and 150mA.
Measure the voltage on the panel as well as on the output of the converter module. It should be 5v (+/- 5%) on the converter module and the solar panel should have dropped from the open-circuit voltage too (but still needs to be above 9v).
Measure the current on the same ^
Then attach a USB device, such as a partially charged portable battery pack, and re-measure all voltages while the pack hopefully pulls up to 500mA.

We might find the reason for a lack of charge then!

Solar Panel Project For School

Comments