Advertisement
If you have a new account but are having problems posting or verifying your account, please email us on hello@boards.ie for help. Thanks :)
Hello all! Please ensure that you are posting a new thread or question in the appropriate forum. The Feedback forum is overwhelmed with questions that are having to be moved elsewhere. If you need help to verify your account contact hello@boards.ie
Please note that it is not permitted to have referral links posted in your signature. Keep these links contained in the appropriate forum. Thank you.

https://www.boards.ie/discussion/2055940817/signature-rules
Hi there,
There is an issue with role permissions that is being worked on at the moment.
If you are having trouble with access or permissions on regional forums please post here to get access: https://www.boards.ie/discussion/2058365403/you-do-not-have-permission-for-that#latest

2000 Landcruiser front drive shaft nut torque

  • 10-09-2021 5:52pm
    #1
    FintanMcluskey
    Registered Users, Registered Users 2 Posts: 8,526 ✭✭✭


    Hi all

    On the above unit, a 2000 landcruiser, the front LH drive shaft to hub nut was removed and needs to be re-torqued.

    Does anyone know the torque or does it need to be torqued?

    Also does this nut tension the hub bearings when it tightens the drive shaft to the hub, I don't think it does but I'm not at the jeep and I cant picture it in my head?

    Thanks



Comments

  • #2
    [Deleted User]
    Posts: 468 ✭✭ [Deleted User]


    May be it helps


    SUSPENSION AND AXLE


    FRONT AXLE HUB


    INSTALLATION

    1.INSTALL AXLE HUB TO STEERING KNUCKLE

    (a) Place the axle hub with disc to the steering knuckle.

    NOTICE:

    Be careful not to damage the ABS speed sensor rotor and

    oil seal.

    (b) Install the outer bearing.

    (c) Install the claw washer.


    2.ADJUST PRELOAD

    (a) Install the adjusting nut and using SST, tighten it.

    SST 09607-60020

    (b)Torque: 59 N·m (600 kgf·cm, 43 ft·lbf)

    Turn the axle hub several times to settle down the bear-

    ing.

    (c)Using SST, loosen the adjusting nut until it can rotate by

    hand.

    SST 09607-60020

    (d) Using SST, retighten the adjusting nut.

    SST 09607-60020

    Torque: 4.3 - 6.5 N·m (44 - 66 kgf·cm, 38 - 57 in.·lbf)

    HINT:

    Check that there is no looseness on the bearing.

    (e) Using a spring tension gauge, measure the preload.

    Preload (at starting):

    42 - 67 N (4.3 - 6.8 kgf, 9.5 - 15.0 lbf)


    3. INSTALL LOCK WASHER AND LOCK NUT

    (a) Install a new lock washer and the lock nut.

    (b) Using SST, torque the lock nut.

    SST 09607-60020

    Torque: 64 N·m (650 kgf·cm, 47 ft·lbf)

    (c) Check that the axle hub rotates smoothly and there is no

    looseness on the bearing.


    (d) Using a spring tension gauge, check the preload.

    Preload (at starting):

    42 - 67 N (4.3 - 6.8 kgf, 9.5 - 15.0 lbf)


    HINT:

    Make sure to check preload in the direction of rotation.

    If the preload is not within the specified value, adjust it again

    with the adjusting nut.

    (e) Secure the lock nut by bending one of the lock washer

    teeth inward and the other lock washer teeth outward.


    4.INSTALL FLANGE

    (a) Place a new gasket in position on the axle hub.

    (b) Install the flange to the axle hub.

    (c) Install the 6 cone washers, washers and new nuts.

    Torque: 33 N·m (335 kgf·cm, 24 ft·lbf)

    (d) Pull out the drive shaft to the outside of the vehicle and

    select the snap ring which ensures the clearance be-

    tween the tip of the flange and the snap ring is less than

    0.2 mm (0.008 in.).

    Snap ring thickness:

    1.8 mm (0.0709 in.) 2.4 mm (0.0945 in.)

    2.0 mm (0.0787 in.) 2.6 mm (0.1024 in.)

    2.2 mm (0.0866 in.) 2.8 mm (0.1102 in.)

    (e)Using a snap ring expander, install a new snap ring to the

    drive shaft.

    (f) Install a new grease cap to the flange.


    5. INSTALL BRAKE CALIPER

    (a)Install the brake caliper, washers and 2 bolts.

    Torque: 123 N·m (1,250 kgf·cm, 91 ft·lbf)

    (b) Install the flexible hose and bolt to the steering knuckle.

    Torque: 28 N·m (290 kgf·cm, 21 ft·lbf)


    6.INSTALL FRONT WHEEL

    Torque: 131 N·m (1,340 kgf·cm, 97 ft·lbf)


    7.CHECK ABS SPEED SENSOR SIGNAL



Advertisement