Aerial Direction for Saorview

fuse

Thurston? wrote: »

The connector should come with a reducer for the centre core: just a pin that fits on the end of the wire, & in turn will fit into a female f-connector.

That's perfect so.
After a bit of playing around and a retune I managed to get more channels including the BBC ones. Although the quality is not good, they break up constantly.
Will have to improve the connector on the main cable and hope for the best...

fuse

The Cush wrote: »

Look at the video on that page I linked to for the connector, it'll show you how to make the connector. Ensure the core wire and braid don't make contact, but the braid must make contact with the outer threaded portion of the connector.

You'll see there is a plastic collar and central contact pin or reducer as they call it in the video, which would work in your situation. But the text on the page says the plastic collar isn't available but not sure about the contact pin/reducer is also missing. The plastic collar is used to hold the central pin in place. Perhaps you could give them a call.

Looks like there is a standard F connection on the other end as he connects it to an F connector joiner. Might get in touch just to be sure alright

The Cush

fuse wrote: »

Looks like there is a standard F connection on the other end as he connects it to an F connector joiner. Might get in touch just to be sure alright

It is a standard F connection but for a heavy duty 10mm co ax cable, the question is the reducer pin and plastic retainer included with the connector for you to use with the power supply. It may be possible for the core wire to go into the power supply without the reducer using a little bit of gentle persuasion.

The Cush

This connector is for 10mm RG11 co ax cable, same external diameter as CT165 cable but is a crimp version with pin and plastic insert. Assembly drawing link to the right of the page

http://uk.rs-online.com/web/p/f-connectors/7123380/

fuse

The Cush wrote: »

This connector is for 10mm RG11 co ax cable, same external diameter as CT165 cable but is a crimp version with pin and plastic insert. Assembly drawing link to the right of the page

http://uk.rs-online.com/web/p/f-connectors/7123380/

Thanks I see what you mean by the reducer pin. I'll check with freetv first, as I don't have a crimping tool.

Thurston?

fuse wrote: »

Looks like there is a standard F connection on the other end as he connects it to an F connector joiner.

Even if it doesn't come with the pin, the little jaws inside the female f should accept the heavier wire, it's just that they won't return to their original width once they're forced far enough apart, so the PSU probably won't work again with thinner wire.

If you wanted to avoid this, you could always use an f-joiner, & connect the heavy cable to a short length of something lighter.

fuse

Just to update and conclude my troubleshooting..

I got the CT165 adapter with step-down pin for the main cable coming from the masthead and it fit really well into the power adapter. Also got a new male-male coax for the wall to tv connection as I was using female-male adapter that was a bit loose.

Now all the Freeview channels are almost perfect quality, the odd flicker now and again. Saorview are crystal clear.
Delighted to be able to get 20+ decent channels and radio aswell. Well worth spending the few bob on power supply to give me bill free viewing from now on!

Thanks again for all the detailed help and advice Cush & Thurston. Also FreeTV.ie guys were really helpful and my orders arrived next day.

fuse

I'm reviving this thread I started as I'm back trying to figure things out...

I can no longer receive the freeview stations and not sure why.

I took a better picture of the aerial and can see there is 1 single cable running from it down to the attic. I still can't see if there is working power on the masthead.
Aerials are pointing Due North in Dun Laoghaire area




The single cable was originally running into a diplexer or splitter. From what I could see, it was just splitting the signal coming from the masthead to two cables running to separate TV points.

I removed it from this splitter and ran it into a proception 12v power supply and a cable for the output to TV.


I now have an Edision DVB-T2 box and can see an almost 100% strength signal coming from Clermont Carn (52 56) which is the strongest signal and gives clear Saorview channels - this is only when it runs through the 12v power, otherwise Three Rock is stronger.

I expect to be able to pick up freeview from Divis or Limavady? But not receiving anything at those Muxes. The box is searching DVB-T and DVB-T2.

I'm confused why a diplexer was there in the first place... this is usually to split UHF and VHF signals? Is it necessary here?
Hoping to get some professional advice to look at it if I can't figure it out. Would appreciate any recommendations via PM if that's allowed...

Thurston?

fuse wrote: »

... The single cable was originally running into a diplexer or splitter. From what I could see, it was just splitting the signal coming from the masthead to two cables running to separate TV points.

I removed it from this splitter and ran it into a proception 12v power supply and a cable for the output to TV.



I expect to be able to pick up freeview from Divis or Limavady? But not receiving anything at those Muxes. The box is searching DVB-T and DVB-T2.

I'm confused why a diplexer was there in the first place... this is usually to split UHF and VHF signals? Is it necessary here?

Was that the red box pictured in an earlier post? Wasn't it just an ordinary splitter? (No reason for it to be anything else.)

Those aerials are set up to receive Freeview from Kilkeel. (2 x group B at the top of the mast, & then the single group C/D for Clermont Carn.) If it was me at your location, I'd just forget about Freeview as any kind of reliable service, & frequency changes later this year in NI won't do it any more favours.

fuse

Thurston? wrote: »

Was that the red box pictured in an earlier post? Wasn't it just an ordinary splitter? (No reason for it to be anything else.)

Those aerials are set up to receive Freeview from Kilkeel. (2 x group B at the top of the mast, & then the single group C/D for Clermont Carn.) If it was me at your location, I'd just forget about Freeview as any kind of reliable service, & frequency changes later this year in NI won't do it any more favours.

Yes the red box from earlier pic - it must have been an ordinary splitter alright. I'm only using one of the TV points at the moment.

How can you tell the 2 x group B and group C/D, all three look exactly the same?

Ahh so it sounds like I'm really barking up the wrong tree with freeview!
The edision box also has DVB-S2 - I'll need to install a dish so if I want the UK channels.
Thanks for the info

Thurston?

fuse wrote: »

... How can you tell the 2 x group B and group C/D, all three look exactly the same?

The top 2 have slightly longer elements, & are a bit longer overall, due to the longer wavelengths (lower frequencies) they're intended for.