GS Air - Filling a hole !!

Tom Cruises Left Nut

Howdy

My GS Air has 2 air holes and a middle hole where a screw goes to control the air flow

The problem is the screw fell out and is a gonner

Wondering what I could use to block that hole, am thinking glue is a bad idea due to me inhaling it !!!

Inquitus

Tom Cruises Left Nut wrote: »

Howdy

My GS Air has 2 air holes and a middle hole where a screw goes to control the air flow

The problem is the screw fell out and is a gonner

Wondering what I could use to block that hole, am thinking glue is a bad idea due to me inhaling it !!!

I would have thought epoxy resin would do the job.

Tom Cruises Left Nut

Inquitus wrote: »

I would have thought epoxy resin would do the job.

Ah cheers !

Tickityboo

Tom Cruises Left Nut wrote: »

Howdy

My GS Air has 2 air holes and a middle hole where a screw goes to control the air flow

The problem is the screw fell out and is a gonner

Wondering what I could use to block that hole, am thinking glue is a bad idea due to me inhaling it !!!

A little bit of sellotape over it would do the job

Tom Cruises Left Nut

Tickityboo wrote: »

A little bit of sellotape over it would do the job

It falls off though

Tickityboo

Tom Cruises Left Nut wrote: »

It falls off though

That's a pain in the butt!!

Tom Cruises Left Nut

Tickityboo wrote: »

That's a pain in the butt!!

It sure is !!!!

Too cheap to pay 12.50 for a whole new unit ! Ha

dohouch

BluTak.

Trond

Tom Cruises Left Nut wrote: »

It sure is !!!!

Too cheap to pay 12.50 for a whole new unit ! Ha

Tenner on bestshop!

I'm sure you could get a replacement in a decent hardwear shop? Maybe even try a jewellers?

youdipstick

Shove a match stick in & then break it off or a slither of wood if match stick is too small.

Tom Cruises Left Nut

Cheers lads, ended up unclogging a drain last night but will try some of these suggestions !

Appreciate it !

RIchieNouveau

Tom Cruises Left Nut wrote: »

Cheers lads, ended up unclogging a drain last night but will try some of these suggestions !

Appreciate it !

So, the complete opposite of what you wanted to do here...

Tom Cruises Left Nut

RIchieNouveau wrote: »

So, the complete opposite of what you wanted to do here...

Story of my life......

:pac:

Lu Tze

Tom Cruises Left Nut wrote: »

Story of my life......

:pac:

Some sugru should do the job

28srf0c

youdipstick wrote: »

Shove a match stick in & then break it off or a slither of wood if match stick is too small.

That would look hideous.

youdipstick

28srf0c wrote: »

That would look hideous.

This clearo is for vaping & not for a fashion show,no vanity here buddy,if it works...what the fcuk:D:D

28srf0c

Well I'd prefer not to be walking around a pub with a match stick and duct tape hanging off my e-cig.

youdipstick

28srf0c wrote: »

Well I'd prefer not to be walking around a pub with a match stick and duct tape hanging off my e-cig.

:D:D:D Ok,I get your point alright,I specifically bought wooden Croatia needles 1mm to 5mm thick from China for 40c & they have fixed a lot of holes for me on different devices over the past 6 years of vaping.
The amount of work we had to do to devices to improve them would be insane in today's market,always drilling out air holes & stuffing them,even today I watched a YT video & the reviewer used insulation tape on a regulated box mod to stop the battery door from rattling,always remember to keep your duct tape safe,you never know when you might need it:D:D:D (sorry for going off topic) I actually used it on my Mercedes A Class last year,I managed to break the plastic sill & the cost for a new one was over €700,lucky for me the car is black & the €3 duct tape fixed it good,it can't be seen from a distance & the car has been through many washes.
Anyway,back to the GS Air,the screw disappears into the hole,so the match or cocktail stick wouldn't be seen.
I screwed one of mine in good & tight & it gave a very tight draw but still able to do mouth to lung with it.
So this might fix Tom Cruiser Left Nut :D:D:D:D:D great username:D:D

Hellrazer

Ive a spare gs air with the threads stripped off the 501 connection.Youre welcome to the screw out of it.
Pm me and Ill pop them in the post for you.